Replacement of the Extruded Rubber Seal

TASK 52-13-18-960-801-A
Replacement of the Extruded Rubber Seal

WARNING: DO NOT OPEN OR GO NEAR PRESSURE-SEALED DOORS WHEN THE AIRCRAFT IS PRESSURIZED. A PRESSURE-SEALED DOOR THAT OPENS WHEN THE AIRCRAFT IS PRESSURIZED:

WILL CAUSE EXPLOSIVE DECOMPRESSION.
CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAUSE DAMAGE TO THE AIRCRAFT OR EQUIPMENT.

WARNING: DO NOT OPEN THE PASSENGER/CREW DOOR IF THE WIND SPEED IS MORE THAN 65 KNOTS.

WARNING: STOP THE OPENING PROCEDURE IF THE RED WARNING LIGHT FLASHES. IF THE RED WARNING LIGHT FLASHES, REMAINING PRESSURE CAN CAUSE THE DOOR TO OPEN SUDDENLY AND CAN:

KILL OR CAUSE SERIOUS INJURY TO PERSONS
CAUSE DAMAGE TO THE AIRCRAFT.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

WARNING: BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:

THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
THE PERCUSSION LEVER OF THE DOOR-DAMPER AND EMERGENCY-OPERATION CYLINDER IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.

IF YOU DO NOT OBEY THESE INSTRUCTIONS, THE DOOR CAN OPEN WITH FORCE OR THE ESCAPE SLIDE CAN DEPLOY SUDDENLY. THIS CAN CAUSE INJURY AND/OR DAMAGE.

ZONE: 832
ZONE: 842

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE
No specific	1	BRUSH - BRISTLED, STIFF
No specific	1	SCRAPER - NON METALLIC

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.05RAB9)	Adhesive Film Tape-- Aluminium Foil -
(Material No.06CMD9)	Silicone Adhesive Sealant-General Purpose One part legacy
(Material No.08BAA9)	Non Aqueous Cleaner-General - -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
832	AFT PASSENGER/CREW DOOR
842	AFT PASSENGER/CREW DOOR
832, 842

D. Expendable Parts

FIG.ITEM	DESIGNATION	IPC-CSN
1	EXTRUDED RUBBER SEAL	AIPC 52-13-18-01-410
1	EXTRUDED RUBBER SEAL	AIPC 52-13-84-27-460

E. Referenced Information

REFERENCE	DESIGNATION
TASK 52-10-00-860-001-A	Special Precautions before Work on the Passenger/Crew Door
TASK 52-10-00-860-002-A	Special Precautions after Work on the Passenger/Crew Door
Replacement of the Extruded Rubber Seal

3. Job Set-up
Subtask 52-13-18-941-055-A

A. Get Access
(1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position at zone 832 or 842.
(2) Obey the special precautions before you start the work on the passenger/crew door (Ref. AMM TASK 52-10-00-860-001).

4. Procedure
Subtask 52-13-18-960-050-A

A. Replacement of the Extruded Rubber Seal
(1) If installed, remove the Adhesive Film Tape-- Aluminium Foil - (Material No.05RAB9) .
(2) Remove the defective extruded rubber seal (1).
(3) Remove the remaining adhesive tape with the SCRAPER - NON METALLIC and the BRUSH - BRISTLED, STIFF.
(4) Clean the surfaces with Non Aqueous Cleaner-General - - (Material No.08BAA9) .
(5) Install the new AIPC 52-13-18-01-410 EXTRUDED RUBBER SEAL (1) or the new AIPC 52-13-84-27-460 EXTRUDED RUBBER SEAL (1) with Silicone Adhesive Sealant-General Purpose One part legacy (Material No.06CMD9) .
(6) If necessary, install the new Adhesive Film Tape-- Aluminium Foil - (Material No.05RAB9) .
(7) Make sure that the extruded rubber seal (1) is in the correct position.
(8) Do an operational check of the applicable passenger/crew door to make sure that it continues to open and close correctly.

5. Close-up
Subtask 52-13-18-942-057-A

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Obey the special precautions after you did the work on the passenger/crew door (Ref. AMM TASK 52-10-00-860-002).
(3) Remove the access platform(s).

[Rev.10 from 2021] 2026.04.02 06:27:29 UTC