DOC AIRBUS | AMM A320FInstallation of the Door-Damper and Emergency-Operation Cylinder
TASK 52-13-14-400-001-B
Installation of the Door-Damper and Emergency-Operation Cylinder
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Expendable Parts
E. Referenced Information
3. Job Set-up
Subtask 52-13-14-860-056-A
Subtask 52-13-14-820-054-A
Subtask 52-13-14-410-070-A
[Rev.10 from 2021]
2026.04.02 07:22:19 UTC
Installation of the Door-Damper and Emergency-Operation Cylinder
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | Torque wrench: range to between 0.7 and 0.35 m.daN (61.95 and 30.97 lbf.in )  | |
| No specific | Torque wrench: range to between 1.7 and 1 m.daN (150.44 and 88.50 lbf.in ) | |
| 98D52103003000 | 1 | ADJUSTING-CYLINDER LENGTH |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.14QFB1) | Wire-Locking Dia: 0.8 mm CRES Nickel Alloy - |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 832, 832FZ, 832GZ, 842, 842FZ, 842GZ |
| FIG.ITEM | DESIGNATION | IPC-CSN |
|---|---|---|
| 1 | COTTER PIN | AIPC 52-13-04-01-010 |
| 18 | COTTER PIN | AIPC 52-13-04-01-100 |
| 1 | COTTER PIN | AIPC 52-13-84-05-010 |
| 18 | COTTER PIN | AIPC 52-13-84-05-100 |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 23-73-00-740-005-B | Interface and Power-Up Test of the Cabin Intercommunication Data System (CIDS) through the CFDS |
| TASK 23-73-00-861-001-A | Energize the Cabin Intercommunication Data System (CIDS) |
| TASK 23-73-00-862-001-A | De-energize the Cabin Intercommunication Data System (CIDS) |
| TASK 25-23-46-400-002-A | Installation of the Door Linings on the Aft Passenger/Crew Doors |
| TASK 52-10-00-010-001-A | Opening of the Passenger/Crew Door |
| TASK 52-10-00-410-001-A | Closing of the Passenger/Crew Door |
| TASK 52-10-00-614-001-A | Discharging/Charging of the Door Damper and Emergency Operation Cylinder of the Passenger/Crew Doors |
| TASK 52-10-00-860-001-A | Special Precautions before Work on the Passenger/Crew Door |
| TASK 52-10-00-860-002-A | Special Precautions after Work on the Passenger/Crew Door |
| TASK 52-13-14-200-001-A | Inspection/Check of the Damper and Emergency Operation Cylinder of the Aft Passenger/Crew Door |
| TASK 52-13-14-220-001-A | Detailed Visual Inspection of the Mechanism of the Door-Damper and Emergency- Operation Cylinder |
| TASK 52-13-14-820-002-A | Adjustment of the Percussion Bellcrank Finger of the Door Damper and Emergency Operation Cylinder of the AFT Passenger/Crew Door |
Subtask 52-13-14-860-056-A
A. Aircraft Maintenance Configuration
(1) Make sure that the access platform is in position.
(2) Make sure that the aft passenger/crew door is open (Ref. AMM TASK 52-10-00-010-001).
(3) Make sure that the special precautions are obeyed (Ref. AMM TASK 52-10-00-860-001).
Subtask 52-13-14-865-068-A (1) Make sure that the access platform is in position.
(2) Make sure that the aft passenger/crew door is open (Ref. AMM TASK 52-10-00-010-001).
(3) Make sure that the special precautions are obeyed (Ref. AMM TASK 52-10-00-860-001).
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
Subtask 52-13-14-862-057-B ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C ALL | |||
| 121VU | EIS/SLIDES/ARM AND WARN/FLT | 15WN | P11 |
| 121VU | EIS/SLIDES/ARM AND WARN/GND | 13WN | P10 |
| 121VU | EIS/SDAC1 AND 2/DOOR/DET/PAX | 48WV | P05 |
C. Make sure that the Cabin Intercommunication Data System (CIDS) is de-energized (Ref. AMM TASK 23-73-00-862-001).
Subtask 52-13-14-220-053-A D. Preparation for Installation
(1) Clean the component interfaces and the adjacent area.
(2) Do an inspection of the component interfaces and the adjacent area.
(3) Make sure that the parts retained from the removed component are clean and in the correct condition.
(Ref. AMM TASK 52-13-14-220-001)
4. Procedure(1) Clean the component interfaces and the adjacent area.
(2) Do an inspection of the component interfaces and the adjacent area.
(3) Make sure that the parts retained from the removed component are clean and in the correct condition.
(Ref. AMM TASK 52-13-14-220-001)
Subtask 52-13-14-820-054-A
A. Adjustment of the Length of the Damper and Emergency-Operation Cylinder
Door-Damper and Emergency-Operation Cylinder ** ON A/C NOT FOR ALL
Door-Damper and Emergency-Operation Cylinder ** ON A/C NOT FOR ALL
(1) Manually put the door damper and emergency-operation cylinder in the fully compressed position.
(2) Make sure that the protrusion length J2 of the piston rod:
(a) for the damper series P/N FE174 and FE196 is 16.8 -1.8 mm or +1.8 mm (0.6614 -0.0709 in. or +0.0709 in.).
(b) for the damper series P/N FE240 is 21.8 -1.8 mm or +1.8 mm (0.8583 -0.0709 in. or +0.0709 in.).
(3) If the protrusion length J2 is not in the tolerances, send the damper and emergency-operation cylinder to the manufacturer for overhaul.
(4) In this configuration, adjust the length J3 with the 98D52103003000 ADJUSTING-CYLINDER LENGTH:
(a) Remove the lockwire from the nut (20).
(b) Loosen the nut (20).
(c) Adjust the cylinder (19) to get the length J3.
1 for the damper and emergency-operation cylinder series P/N FE174 and FE196 358 mm (14.0945 in.).
2 for the damper and emergency-operation cylinder series P/N FE240 363 +0.0 mm or -2.0 mm (14.2913 +0.0000 in. or -0.0787 in.).
(d) Tighten the nut (20) and safety with14QFB1 Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -
Subtask 52-13-14-420-058-A ** ON A/C NOT FOR ALL Door-Damper and Emergency-Operation Cylinder ** ON A/C NOT FOR ALL Door-Damper and Emergency-Operation Cylinder ** ON A/C NOT FOR ALL (2) Make sure that the protrusion length J2 of the piston rod:
(a) for the damper series P/N FE174 and FE196 is 16.8 -1.8 mm or +1.8 mm (0.6614 -0.0709 in. or +0.0709 in.).
(b) for the damper series P/N FE240 is 21.8 -1.8 mm or +1.8 mm (0.8583 -0.0709 in. or +0.0709 in.).
(3) If the protrusion length J2 is not in the tolerances, send the damper and emergency-operation cylinder to the manufacturer for overhaul.
(4) In this configuration, adjust the length J3 with the 98D52103003000 ADJUSTING-CYLINDER LENGTH:
(a) Remove the lockwire from the nut (20).
(b) Loosen the nut (20).
(c) Adjust the cylinder (19) to get the length J3.
1 for the damper and emergency-operation cylinder series P/N FE174 and FE196 358 mm (14.0945 in.).
2 for the damper and emergency-operation cylinder series P/N FE240 363 +0.0 mm or -2.0 mm (14.2913 +0.0000 in. or -0.0787 in.).
(d) Tighten the nut (20) and safety with
B. Installation of the Door-Damper and Emergency-Operation Cylinder
(1) Put the yoke (6) in position and install the yoke pin (5) in the cylinder end fitting.
(2) Install the two circlips (4) at the two ends of the yoke pin (5).
(3) Put the cylinder end fitting on the support arm and hold it.
(4) Install the bush (7).
(5) Install the washer (8) and the bolt (9).
(6) Install the washer (3) and the nut (2). Do not tighten the nut (2).
(7) Install the bushes (23) and (24) on the fork (11).
(8) Install the washer (13), the bushes (15), the end of the door-damper and emergency-operation cylinder (10), the washer (16), the fork (11), the bolt (12) and the nut (17).
, and the nut (17) to between 1.7 and 1 m.daN (150.44 and 88.50 lbf.in ) .
(10) Install the AIPC 52-13-04-01-010 COTTER PIN (1), and the AIPC 52-13-04-01-100 COTTER PIN (18).
Subtask 52-13-14-740-051-A ** ON A/C NOT FOR ALL (1) Put the yoke (6) in position and install the yoke pin (5) in the cylinder end fitting.
(2) Install the two circlips (4) at the two ends of the yoke pin (5).
(3) Put the cylinder end fitting on the support arm and hold it.
(4) Install the bush (7).
(5) Install the washer (8) and the bolt (9).
(6) Install the washer (3) and the nut (2). Do not tighten the nut (2).
(7) Install the bushes (23) and (24) on the fork (11).
(8) Install the washer (13), the bushes (15), the end of the door-damper and emergency-operation cylinder (10), the washer (16), the fork (11), the bolt (12) and the nut (17).
NOTE: If you install a new bolt (12) drill a hole of dia. 2 mm (0.0787 in.) for the cotter pin installation.
(9) TORQUE the nut (2) to between 0.7 and 0.35 m.daN (61.95 and 30.97 lbf.in ) , and the nut (17) to between 1.7 and 1 m.daN (150.44 and 88.50 lbf.in ) . (10) Install the AIPC 52-13-04-01-010 COTTER PIN (1), and the AIPC 52-13-04-01-100 COTTER PIN (18).
C. Not Applicable
Subtask 52-13-14-420-058-B ** ON A/C NOT FOR ALL D. Installation of the Door-Damper and Emergency-Operation Cylinder
(1) Put the yoke (6) in position and install the yoke pin (5) in the cylinder end fitting.
(2) Install the two circlips (4) at the two ends of the yoke pin (5).
(3) Put the cylinder end fitting on the support arm and hold it.
(4) Install the bush (7).
(5) Install the washer (8) and the bolt (9).
(6) Install the washer (3) and the nut (2). Do not tighten the nut (2).
(7) Install the bushes (23) and (24) on the fork (11).
(8) Install the washer (13), the bushes (15), the end of the door-damper and emergency-operation cylinder (10), the washer (16), the fork (11), the bolt (12) and the nut (17).
, and the nut (17) to between 1.7 and 1 m.daN (150.44 and 88.50 lbf.in ) .
(10) Install the AIPC 52-13-04-01-010 COTTER PIN (1) or AIPC 52-13-84-05-010 COTTER PIN (1), and the AIPC 52-13-04-01-100 COTTER PIN (18) or AIPC 52-13-84-05-100 COTTER PIN (18).
(11) Connect the connector (22) to the receptacle housing (21).
Subtask 52-13-14-740-051-B ** ON A/C NOT FOR ALL (1) Put the yoke (6) in position and install the yoke pin (5) in the cylinder end fitting.
(2) Install the two circlips (4) at the two ends of the yoke pin (5).
(3) Put the cylinder end fitting on the support arm and hold it.
(4) Install the bush (7).
(5) Install the washer (8) and the bolt (9).
(6) Install the washer (3) and the nut (2). Do not tighten the nut (2).
(7) Install the bushes (23) and (24) on the fork (11).
(8) Install the washer (13), the bushes (15), the end of the door-damper and emergency-operation cylinder (10), the washer (16), the fork (11), the bolt (12) and the nut (17).
NOTE: If you install a new bolt (12) drill a hole of dia. 2 mm (0.0787 in.) for the cotter pin installation.
(9) TORQUE the nut (2) to between 0.7 and 0.35 m.daN (61.95 and 30.97 lbf.in ) , and the nut (17) to between 1.7 and 1 m.daN (150.44 and 88.50 lbf.in ) . (10) Install the AIPC 52-13-04-01-010 COTTER PIN (1) or AIPC 52-13-84-05-010 COTTER PIN (1), and the AIPC 52-13-04-01-100 COTTER PIN (18) or AIPC 52-13-84-05-100 COTTER PIN (18).
(11) Connect the connector (22) to the receptacle housing (21).
E. BITE Test
(1) Do a BITE test of the Cabin Intercommunication Data System (CIDS) (Ref. AMM TASK 23-73-00-740-005).
Subtask 52-13-14-220-056-A (1) Do a BITE test of the Cabin Intercommunication Data System (CIDS) (Ref. AMM TASK 23-73-00-740-005).
F. Check of the Door Opening/Closing
Door-Damper and Emergency-Operation Cylinder ** ON A/C NOT FOR ALL
Door-Damper and Emergency-Operation Cylinder ** ON A/C NOT FOR ALL
(1) When you lock/unlock the door, make sure that the clearance J4 between the telescopic rod and the door attach fitting (23) is 1.5 mm (0.0591 in.) minimum.
Subtask 52-13-14-614-055-A Door-Damper and Emergency-Operation Cylinder ** ON A/C NOT FOR ALL Door-Damper and Emergency-Operation Cylinder ** ON A/C NOT FOR ALL G. Charging after Storage
(1) If you discharged the door damper and emergency operation cylinder for the repair in shop, charge the cylinder (Ref. AMM TASK 52-10-00-614-001).
Subtask 52-13-14-210-061-A (1) If you discharged the door damper and emergency operation cylinder for the repair in shop, charge the cylinder (Ref. AMM TASK 52-10-00-614-001).
H. Check of the Pressure
(1) Do a check of the pressure of the door damper and emergency operation cylinder (Ref. AMM TASK 52-13-14-200-001).
Subtask 52-13-14-820-055-A (1) Do a check of the pressure of the door damper and emergency operation cylinder (Ref. AMM TASK 52-13-14-200-001).
I. Adjustment of the Percussion Bellcrank Finger
(1) Adjust the percussion bellcrank finger (Ref. AMM TASK 52-13-14-820-002).
5. Close-up(1) Adjust the percussion bellcrank finger (Ref. AMM TASK 52-13-14-820-002).
Subtask 52-13-14-410-070-A
A. Installation of the Support Arm Lining
(1) Install the door support arm lining panels (Ref. AMM TASK 25-23-46-400-002).
(a) For the left passenger/crew door: 832FZ 832GZ.
(b) For the right passenger/crew door: 842FZ 842GZ.
Subtask 52-13-14-861-055-A ** ON A/C NOT FOR ALL (1) Install the door support arm lining panels (Ref. AMM TASK 25-23-46-400-002).
(a) For the left passenger/crew door: 832FZ 832GZ.
(b) For the right passenger/crew door: 842FZ 842GZ.
B. Not Applicable
Subtask 52-13-14-861-055-B ** ON A/C NOT FOR ALL Subtask 52-13-14-865-069-A C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
Subtask 52-13-14-410-071-A | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C ALL | |||
| 121VU | EIS/SLIDES/ARM AND WARN/FLT | 15WN | P11 |
| 121VU | EIS/SLIDES/ARM AND WARN/GND | 13WN | P10 |
| 121VU | EIS/SDAC1 AND 2/DOOR/DET/PAX | 48WV | P05 |
D. Close Access
(1) Arm the percussion mechanism of the door damper and emergency operation cylinder. To do this, obey the special precautions after the work on the door (Ref. AMM TASK 52-10-00-860-002).
(2) Make sure that the work area is clean and clear of tools and other items.
(3) Close the passenger/crew door (Ref. AMM TASK 52-10-00-410-001), 832 842.
(4) Remove the access platform(s).
(1) Arm the percussion mechanism of the door damper and emergency operation cylinder. To do this, obey the special precautions after the work on the door (Ref. AMM TASK 52-10-00-860-002).
(2) Make sure that the work area is clean and clear of tools and other items.
(3) Close the passenger/crew door (Ref. AMM TASK 52-10-00-410-001), 832 842.
(4) Remove the access platform(s).