DOC AIRBUS | AMM A320FInstallation of the Aft Passenger/Crew-Doors Gust-Lock Control-Mechanism
TASK 52-13-12-400-802-A
Installation of the Aft Passenger/Crew-Doors Gust-Lock Control-Mechanism
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
B. Expendable Parts
C. Referenced Information
3. Job Set-up
Subtask 52-13-12-860-052-A
Subtask 52-13-12-420-060-A
Subtask 52-13-12-420-061-A
[Rev.10 from 2021]
2026.04.02 07:21:55 UTC
Installation of the Aft Passenger/Crew-Doors Gust-Lock Control-Mechanism
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 832 | AFT PASSENGER/CREW DOOR |
| 842 | AFT PASSENGER/CREW DOOR |
| 832FZ, 832GZ, 842FZ, 842GZ |
| FIG.ITEM | DESIGNATION | IPC-CSN |
|---|---|---|
| 7 | COTTER PIN | AIPC 52-13-04-08-050 |
| 16 | COTTER PIN | AIPC 52-13-04-08-183 |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 24-42-00-862-001-A | De-energize the Ground Service Network Supplied from the External Power |
| TASK 25-23-46-000-002-A | Removal of the Door Linings from the Aft Passenger/Crew Doors |
| TASK 25-23-46-400-002-A | Installation of the Door Linings on the Aft Passenger/Crew Doors |
Gust-Lock Control-MechanismSubtask 52-13-12-860-052-A
A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
(2) Make sure that the linings on the support arms at the aft passenger/crew doors are removed (Ref. AMM TASK 25-23-46-000-002):
Subtask 52-13-12-220-062-A (1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
(2) Make sure that the linings on the support arms at the aft passenger/crew doors are removed (Ref. AMM TASK 25-23-46-000-002):
B. Prepare for the Installation
(1) Clean the component interfaces and the adjacent area.
(2) Do an inspection of the component interfaces and the adjacent area.
(3) Make sure that the parts retained from the removed component are clean and in the correct condition.
4. Procedure(1) Clean the component interfaces and the adjacent area.
(2) Do an inspection of the component interfaces and the adjacent area.
(3) Make sure that the parts retained from the removed component are clean and in the correct condition.
Subtask 52-13-12-420-060-A
A. Installation of the Gust-Lock Control-Mechanism
(1) Install the nylon bushes (8) and (10) and guides (9).
(2) Install the pin (5).
(3) Install the arm (14) as follows:
(a) Put the arm (14) in position with the pin (5).
1 Install the pin (19) and washer (6).
2 Install the new AIPC 52-13-04-08-050 COTTER PIN (7).
(b) Put the arm (14) with the door support arm in position.
1 Install washers (11), (13) and the pin (17).
2 Install the bolt (12) and nut (15).
3 Tighten the nut (15).
4 Install the new AIPC 52-13-04-08-183 COTTER PIN (16).
(4) Install the pushbutton switch assembly (4).
(5) Install the handle (1).
(6) Install the bolts (2), washers (3) and nuts (18).
(7) Tighten the nuts (18).
5. Close-up(1) Install the nylon bushes (8) and (10) and guides (9).
(2) Install the pin (5).
(3) Install the arm (14) as follows:
(a) Put the arm (14) in position with the pin (5).
1 Install the pin (19) and washer (6).
2 Install the new AIPC 52-13-04-08-050 COTTER PIN (7).
(b) Put the arm (14) with the door support arm in position.
1 Install washers (11), (13) and the pin (17).
2 Install the bolt (12) and nut (15).
3 Tighten the nut (15).
4 Install the new AIPC 52-13-04-08-183 COTTER PIN (16).
(4) Install the pushbutton switch assembly (4).
(5) Install the handle (1).
(6) Install the bolts (2), washers (3) and nuts (18).
(7) Tighten the nuts (18).
Subtask 52-13-12-420-061-A
A. Install the linings on the support arms at the aft passenger/crew doors (Ref. AMM TASK 25-23-46-400-002):
Subtask 52-13-12-862-052-A