Reactivation of the Passenger/Crew Doors - Load Adjustment

TASK 52-10-00-440-001-A-01
Reactivation of the Passenger/Crew Doors - Load Adjustment

1. Reason for the Job
MMEL 25-62-01B
CABIN DOOR SLIDE OR SLIDE RAFT
There is an alternative method for this procedure. This task gives one of the methods. For the other method refer to the other task in this page block.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.14QFB1)	Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
831, 831AZ, 832, 832AZ, 841, 841AZ, 842, 842AZ

D. Referenced Information

REFERENCE	DESIGNATION
TASK 25-23-46-000-002-A	Removal of the Door Linings from the Aft Passenger/Crew Doors
TASK 25-23-46-400-001-A	Installation of the Door Linings on the Forward Passenger/Crew Doors
TASK 25-23-46-400-002-A	Installation of the Door Linings on the Aft Passenger/Crew Doors
TASK 25-62-44-400-006-A	Installation of the Left Escape-Slide Pack-Assembly
TASK 25-62-44-400-007-A	Installation of the Left-Hand Escape-Slide-Raft Pack-Assembly
TASK 25-62-44-400-802-A	Installation of the Right Escape-Slide Pack-Assembly
TASK 25-62-44-400-803-A	Installation of the Right-Hand Escape-Slide-Raft Pack-Assembly
TASK 52-10-00-010-001-A	Opening of the Passenger/Crew Door
TASK 52-10-00-410-001-A	Closing of the Passenger/Crew Door
TASK 52-10-00-860-001-A	Special Precautions before Work on the Passenger/Crew Door
TASK 52-10-00-860-002-A	Special Precautions after Work on the Passenger/Crew Door
TASK 52-11-00-820-002-A	Load Adjustment of the Control Handle of the FWD Passenger/Crew Door
TASK 52-11-00-820-002-A-01	Load Adjustment of the Control Handle of the FWD Passenger/Crew Door
TASK 52-13-00-820-002-A	Load Adjustment of the Control Handle of the AFT Passenger/Crew Door without the Emergency Escape Slide
TASK 52-13-00-820-002-A-01	Load Adjustment of the Control Handle of the AFT Passenger/Crew Door
Load Adjustment of the Inner Control Handle ** ON A/C NOT FOR ALL
Load Adjustment of the Inner Control Handle ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 52-10-00-010-087-A

A. Get Access
(1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position in the zone 831 (841) or 832 (842).
(2) Open the door 831 841 or 832 842 (Ref. AMM TASK 52-10-00-010-001).
(3) Obey the special precautions before you start work on the door (Ref. AMM TASK 52-10-00-860-001).

Subtask 52-10-00-865-077-A

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
121VU	EIS/SLIDES/ARM AND WARN/FLT	15WN	P11
121VU	EIS/SLIDES/ARM AND WARN/GND	13WN	P10
121VU	EIS/SDAC1 AND 2/DOOR/DET/PAX	48WV	P05

4. Procedure
Subtask 52-10-00-820-053-A ** ON A/C NOT FOR ALL

A. Load Adjustment of the Inner Control Handle

Load Adjustment of the Inner Control Handle ** ON A/C NOT FOR ALL

(1) Remove the lockwire from the screw (2).
(2) Adjust the load (less than or equal to 18 daN (40.47 lbf)) on the inner control handle. To do this tighten the screw (2) by 9 turns to apply a load on the torsion bar (1).
(3) Do a check of the load adjustment of the inner control handle.

For the FWD passenger/crew door (Ref. AMM TASK 52-11-00-820-002).
For the Aft passenger/crew door (Ref. AMM TASK 52-13-00-820-002).

(4) Safety the screw (2) with 14QFB1Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -

Subtask 52-10-00-820-053-B ** ON A/C NOT FOR ALL

A. Load Adjustment of the Inner Control Handle

Load Adjustment of the Inner Control Handle ** ON A/C NOT FOR ALL

(1) Remove the lockwire from the screw (2).
(2) Adjust the load (less than or equal to 18 daN (40.47 lbf)) on the inner control handle. To do this tighten the screw (2) by 20 turns to apply a load on the torsion bar (1).
(3) Do a check of the load adjustment of the inner control handle.

For the FWD passenger/crew door (Ref. AMM TASK 52-11-00-820-002).
For the Aft passenger/crew door (Ref. AMM TASK 52-13-00-820-002).

(4) Safety the screw (2) with 14QFB1Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -

5. Close-up
Subtask 52-10-00-410-096-A ** ON A/C NOT FOR ALL

A. Installation of the Escape Slide
(1) Install the escape slide:
(a) For the left door:
If removed, install the left-hand escape slide pack assembly (Ref. AMM TASK 25-62-44-400-006).
(b) For the right door:
If removed, install the right-hand escape slide pack assembly (Ref. AMM TASK 25-62-44-400-802).
(2) Install the door lining panels:
(a) For the FWD passenger/crew doors:
(Ref. AMM TASK 25-23-46-400-001)

for the left door 831AZ
for the right door 841AZ

(b) For the Aft passenger/crew doors:
(Ref. AMM TASK 25-23-46-400-002)

for the left door 832AZ
for the right door 842AZ

Subtask 52-10-00-410-096-B ** ON A/C NOT FOR ALL

A. Installation of the Escape Slide/Raft
(1) Install the escape slide:
(a) For the left door:
Install the left-hand escape slide raft pack assembly (Ref. AMM TASK 25-62-44-400-007).
(b) For the right door:
Install the right-hand escape slide raft pack assembly (Ref. AMM TASK 25-62-44-400-803).
(2) Install the door lining panels:
(a) For the FWD passenger/crew doors:
(Ref. AMM TASK 25-23-46-400-001).

for the left door 831AZ
for the right door 841AZ

(b) For the Aft passenger/crew doors:
(Ref. AMM TASK 25-23-46-000-002)

for the left door 832AZ
for the right door 842AZ

Subtask 52-10-00-865-078-A

B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
121VU	EIS/SLIDES/ARM AND WARN/FLT	15WN	P11
121VU	EIS/SLIDES/ARM AND WARN/GND	13WN	P10
121VU	EIS/SDAC1 AND 2/DOOR/DET/PAX	48WV	P05

Subtask 52-10-00-410-097-A

C. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Obey the special precautions after the work on the door (Ref. AMM TASK 52-10-00-860-002).
(3) Close the door 831 841 or 832 842 (Ref. AMM TASK 52-10-00-410-001).
(4) Remove the access platform(s).

[Rev.10 from 2021] 2026.04.02 06:27:17 UTC