W DOC AIRBUS | AMM A320F

Reactivation of the Passenger/Crew Doors - Load Adjustment


TASK 52-10-00-440-001-A
Reactivation of the Passenger/Crew Doors - Load Adjustment


1. Reason for the Job
MMEL 25-62-01B
CABIN DOOR SLIDE OR SLIDE RAFT
There is an alternative method for this procedure. This task gives one of the methods. For the other method, refer to the other task in this page block.
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
1
ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE
No specific
AR
SAFETY CLIP - CIRCUIT BREAKER
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
831, 831AZ, 832, 832AZ, 841, 841AZ, 842, 842AZ
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 25-23-46-400-001-A
Installation of the Door Linings on the Forward Passenger/Crew Doors
TASK 25-23-46-400-002-A
Installation of the Door Linings on the Aft Passenger/Crew Doors
TASK 25-62-44-400-006-A
Installation of the Left Escape-Slide Pack-Assembly
TASK 25-62-44-400-007-A
Installation of the Left-Hand Escape-Slide-Raft Pack-Assembly
TASK 25-62-44-400-802-A
Installation of the Right Escape-Slide Pack-Assembly
TASK 25-62-44-400-803-A
Installation of the Right-Hand Escape-Slide-Raft Pack-Assembly
TASK 52-10-00-010-001-A
Opening of the Passenger/Crew Door
TASK 52-10-00-410-001-A
Closing of the Passenger/Crew Door
TASK 52-10-00-860-001-A
Special Precautions before Work on the Passenger/Crew Door
TASK 52-10-00-860-002-A
Special Precautions after Work on the Passenger/Crew Door
TASK 52-11-00-820-002-A
Load Adjustment of the Control Handle of the FWD Passenger/Crew Door
TASK 52-11-00-820-002-A-01
Load Adjustment of the Control Handle of the FWD Passenger/Crew Door
TASK 52-13-00-820-002-A
Load Adjustment of the Control Handle of the AFT Passenger/Crew Door without the Emergency Escape Slide
TASK 52-13-00-820-002-A-01
Load Adjustment of the Control Handle of the AFT Passenger/Crew Door
3. Job Set-up
Subtask 52-10-00-010-070-A
A. Get Access
   (1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position at zone 831(841) or 832(842).
   (2) Open applicable doors 831 841 or 832 842 (Ref. AMM TASK 52-10-00-010-001).
   (3) Obey the special precautions before you start work on the door (Ref. AMM TASK 52-10-00-860-001).
Subtask 52-10-00-865-060-A
B. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C ALL
121VUEIS/SLIDES/ARM AND WARN/FLT15WNP11
121VUEIS/SLIDES/ARM AND WARN/GND13WNP10
121VUEIS/SDAC1 AND 2/DOOR/DET/PAX48WVP05
4. Procedure
Subtask 52-10-00-820-051-A
A. Load Adjustment of the Inner Control Handle
   (1) For the forward passenger/crew door (Ref. AMM TASK 52-11-00-820-002).
   (2) For the aft passenger/crew door (Ref. AMM TASK 52-13-00-820-002).
5. Close-up
Subtask 52-10-00-410-094-A ** ON A/C NOT FOR ALL
A. Installation of the Escape Slide
   (1) Install the escape slide:
     (a) For the left door:
     (b) For the right door:
   (2) Install the door lining panels:
     (a) For the forward passenger/crew doors:
(Ref. AMM TASK 25-23-46-400-001)
     (b) For the aft passenger/crew doors:
(Ref. AMM TASK 25-23-46-400-002)
Subtask 52-10-00-410-094-B ** ON A/C NOT FOR ALL
A. Installation of the Escape Slide Raft
   (1) Install the escape slide:
     (a) For the left door:
     (b) For the right door:
   (2) Install the door lining panels:
     (a) For the forward passenger/crew doors:
(Ref. AMM TASK 25-23-46-400-001).
     (b) For the aft passenger/crew doors:
(Ref. AMM TASK 25-23-46-400-002)
Subtask 52-10-00-865-061-A
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C ALL
121VUEIS/SLIDES/ARM AND WARN/FLT15WNP11
121VUEIS/SLIDES/ARM AND WARN/GND13WNP10
121VUEIS/SDAC1 AND 2/DOOR/DET/PAX48WVP05
Subtask 52-10-00-410-095-A
C. Close Access
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Obey the special precautions after work on the door (Ref. AMM TASK 52-10-00-860-002).
   (3) Close doors 831 841 or 832 842 (Ref. AMM TASK 52-10-00-410-001).
   (4) Remove the access platform(s).
[Rev.10 from 2021] 2026.04.02 06:27:17 UTC