Deactivation of the Passenger/Crew Doors - Load Adjustment

TASK 52-10-00-040-001-A-01
Deactivation of the Passenger/Crew Doors - Load Adjustment

1. Reason for the Job
MMEL 25-62-01B
CABIN DOOR SLIDE OR SLIDE RAFT
There is an alternative method for this procedure. This task gives one of the methods. For the other method refer to the other task in this page block.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.14QFB1)	Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
831, 831AZ, 832, 832AZ, 841, 841AZ, 842, 842AZ

D. Referenced Information

REFERENCE	DESIGNATION
TASK 25-23-46-000-001-A	Removal of the Door Linings from the Forward Passenger/Crew Doors
TASK 25-23-46-000-002-A	Removal of the Door Linings from the Aft Passenger/Crew Doors
TASK 25-62-44-000-002-A	Removal of the Left Escape-Slide Pack-Assembly
TASK 25-62-44-000-010-A	Removal of the Inflated Left Escape-Slide
TASK 25-62-44-000-011-A	Removal of the Inflated Left-Hand Escape-Slide-Raft
TASK 25-62-44-000-012-A	Removal of the Left-Hand Escape-Slide-Raft Pack-Assembly
TASK 25-62-44-000-802-A	Removal of the Right Escape-Slide Pack-Assembly
TASK 25-62-44-000-803-A	Removal of the Inflated Right Escape-Slide
TASK 25-62-44-000-804-A	Removal of the Right-Hand Escape-Slide-Raft Pack-Assembly
TASK 25-62-44-000-805-A	Removal of the Inflated Right-Hand Escape-Slide-Raft
TASK 52-10-00-010-001-A	Opening of the Passenger/Crew Door
TASK 52-10-00-410-001-A	Closing of the Passenger/Crew Door
TASK 52-10-00-860-001-A	Special Precautions before Work on the Passenger/Crew Door
TASK 52-10-00-860-002-A	Special Precautions after Work on the Passenger/Crew Door
Load Adjustment of the Inner Control Handle ** ON A/C NOT FOR ALL
Load Adjustment of the Inner Control Handle ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 52-10-00-010-085-A

A. Get Access
(1) Put the ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE in position in the zone 831 (841) or 832 (842).
(2) Open the applicable passenger/crew door 831 841 or 832 842 (Ref. AMM TASK 52-10-00-010-001).
(3) Obey the special precautions before you start work on the door (Ref. AMM TASK 52-10-00-860-001).

Subtask 52-10-00-865-075-A

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
121VU	EIS/SLIDES/ARM AND WARN/FLT	15WN	P11
121VU	EIS/SLIDES/ARM AND WARN/GND	13WN	P10
121VU	EIS/SDAC1 AND 2/DOOR/DET/PAX	48WV	P05

Subtask 52-10-00-010-086-A ** ON A/C NOT FOR ALL

C. Removal of the Escape Slide
(1) Remove the door lining panels:
(a) For the FWD passenger/crew doors:
(Ref. AMM TASK 25-23-46-000-001)

for the left door 831AZ
for the right door 841AZ

(b) For the Aft passenger/crew doors:
(Ref. AMM TASK 25-23-46-000-002)

for the left door 832AZ
for the right door 842AZ

(2) Remove the escape slide:
(a) For the left door:
If installed, remove the left-hand escape slide pack assembly (Ref. AMM TASK 25-62-44-000-002) or the inflated left-hand escape slide (Ref. AMM TASK 25-62-44-000-010).
(b) For the right door:
If installed, remove the right-hand escape slide pack assembly (Ref. AMM TASK 25-62-44-000-802) or the inflated right-hand escape slide (Ref. AMM TASK 25-62-44-000-803).

Subtask 52-10-00-010-086-B ** ON A/C NOT FOR ALL

C. Removal of the Escape Slide/Raft
(1) Remove the door lining panels:
(a) For the FWD passenger/crew doors:
(Ref. AMM TASK 25-23-46-000-001)

for the left door 831AZ
for the right door 841AZ

(b) For the Aft passenger/crew doors:
(Ref. AMM TASK 25-23-46-000-002)

for the left door 832AZ
for the right door 842AZ

(2) Remove the escape slide:
(a) For the left door:
If installed, remove the left-hand escape slide raft pack assembly (Ref. AMM TASK 25-62-44-000-012) or the inflated left-hand escape slide raft (Ref. AMM TASK 25-62-44-000-011).
(b) For the right door:
If installed, remove the right-hand escape slide raft pack assembly (Ref. AMM TASK 25-62-44-000-804) or the inflated right-hand escape slide raft (Ref. AMM TASK 25-62-44-000-805).

4. Procedure
Subtask 52-10-00-820-052-A ** ON A/C NOT FOR ALL

A. Load Adjustment of the Inner Control Handle

Load Adjustment of the Inner Control Handle ** ON A/C NOT FOR ALL

(1) Remove the lockwire from the screw (2).
(2) Adjust the load (less than or equal to 18 daN (40.47 lbf)) on the inner control handle. To do this loosen the screw (2) by 9 turns to apply a load on the torsion bar (1).

NOTE: If you replace an escape slide by an escape slide/raft you must adjust the load. To do this, tighten the screw (2) by 11 turns.

(3) Safety the screw (2) with 14QFB1Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -.

Subtask 52-10-00-820-052-B ** ON A/C NOT FOR ALL

A. Load Adjustment of the Inner Control Handle

Load Adjustment of the Inner Control Handle ** ON A/C NOT FOR ALL

(1) Remove the lockwire from the screw (2).
(2) Adjust the load (less than or equal to 18 daN (40.47 lbf)) on the inner control handle. To do this loosen the screw (2) by 20 turns to apply a load on the torsion bar (1).

NOTE: If you replace an escape slide/raft by an escape slide you must adjust the load. To do this, loosen the screw (2) by 11 turns.

(3) Safety the screw (2) with 14QFB1Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -

Subtask 52-10-00-220-080-A

B. Inspection

Load Adjustment of the Inner Control Handle ** ON A/C NOT FOR ALL

(1) Pull the inner control handle by 50 mm (1.9685 in.) to 70 mm (2.7559 in.) from the door.
(2) Release the inner control handle.
(3) Make sure that the inner control handle moves back to the door fully closed and locked position.
(4) If the handle does not come back to its initial position, turn the screw (2) by a few more turns until you get this position.

NOTE: It is important to do this final check as the operator does not know the initial adjustment (because of the mechanical wear and differences from one door to another).

5. Close-up
Subtask 52-10-00-865-076-A

A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
121VU	EIS/SLIDES/ARM AND WARN/FLT	15WN	P11
121VU	EIS/SLIDES/ARM AND WARN/GND	13WN	P10
121VU	EIS/SDAC1 AND 2/DOOR/DET/PAX	48WV	P05

Subtask 52-10-00-410-093-A

B. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Obey the special precautions after the work on the door (Ref. AMM TASK 52-10-00-860-002).
(3) Close the door 831 841 or 832 842 (Ref. AMM TASK 52-10-00-410-001).
(4) Remove the access platform(s).
(5) Make an entry in the logbook.

[Rev.10 from 2021] 2026.04.02 06:27:16 UTC