Installation of the Head-End Server Unit Media-Drive

TASK 46-41-39-400-802-A
Installation of the Head-End Server Unit Media-Drive

ZONE: 120
FIN: 1320RF ** ON A/C NOT FOR ALL
FIN: 1620RF ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
120	AVIONICS COMPARTMENT
824

B. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 46-41-00-610-806-A	Parameter loading procedure with the Maintenance Laptop
TASK 46-41-00-610-808-A	Parameter Loading with the USB Flash Drive
TASK 46-41-00-710-804-A	System Monitoring Condition Check
TASK 52-41-00-010-002-A	Open the Avionics Compartment Doors for Access
TASK 52-41-00-410-002-A	Close the Avionics Compartment Doors after Access
TASK 46-41-00-00	CABIN INFORMATION NETWORK SYSTEM - DESCRIPTION AND OPERATION
Head-End Server Unit Media-Drive

3. Job Set-up
Subtask 46-41-39-860-051-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Make sure that the aircraft electrical circuits are energized.
(Ref. AMM TASK 24-41-00-861-002).

Subtask 46-41-39-865-054-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
2000VU	WAP	27MH	D07
2000VU	CINS-RESET-RELAY	20RF	E01

Subtask 46-41-39-010-052-A ** ON A/C NOT FOR ALL

C. Get access to the avionics compartment
(1) For the location of this component, refer to Para. Component Location (Ref. AMM D/O 46-41-00-00).
(2) Make sure that the ACCESS PLATFORM 2M (6 FT) is in position at access door 824.
(3) Make sure that access door 824 is open (Ref. AMM TASK 52-41-00-010-002).

4. Procedure
Subtask 46-41-39-420-051-A ** ON A/C NOT FOR ALL

A. Installation of the Head-End Server-Unit (HESU) media-drive

Head-End Server Unit Media-Drive ** ON A/C NOT FOR ALL

(1) Do an inspection of the component interfaces and the adjacent area.
(2) Clean the component interfaces and the adjacent area.
(3) Make sure that the indicators on the HESU are off.
(4) Installation of the media drive (6): [1620RF]
(a) Make sure that the screw (5) points to the right.
(b) Put the media drive (6) in the upper slot of the HESU (1).
(c) Push the media drive (6) carefully until it is flush with the front plate.
(d) Hand tighten the screw (5).
(5) Installation of the media drive (3): [1320RF]
(a) Make sure that the screw (4) points to the right.
(b) Put the media drive (3) in the lower slot of the HESU (1).
(c) Push the media drive (3) carefully until it is flush with the front plate.
(d) Hand tighten the screw (4).
(6) Close the flap (2) and hand tighten the screw (7).

Subtask 46-41-39-865-055-A ** ON A/C NOT FOR ALL

B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
2000VU	WAP	27MH	D07
2000VU	CINS-RESET-RELAY	20RF	E01

Subtask 46-41-39-600-051-A ** ON A/C NOT FOR ALL

C. Software Loading
(1) Load the parameter after the HESU startup, use the maintenance laptop (Ref. AMM TASK 46-41-00-610-806) or the USB flash drive (Ref. AMM TASK 46-41-00-610-808).

Subtask 46-41-39-710-051-A ** ON A/C NOT FOR ALL

D. Test
(1) Do the system monitoring condition test (Ref. AMM TASK 46-41-00-710-804).

5. Close-up
Subtask 46-41-39-410-051-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2) Make sure that the work area is clean and clear of tools and other items.
(3) Close access door 824 (Ref. AMM TASK 52-41-00-410-002).
(4) Remove the access platform(s).

Subtask 46-41-39-862-051-A ** ON A/C NOT FOR ALL

B. Put the aircraft back to its initial configuration.
(1) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.02 06:26:16 UTC