Forced Load of the Cabin Information Network System (CINS) Platform Parameter

TASK 46-41-00-970-810-A
Forced Load of the Cabin Information Network System (CINS) Platform Parameter

ZONE: 200

1. Reason for the Job
To force a load of the Connectivity System configuration.
2. Job Set-up Information
A. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
200	UPPER HALF FUSELAGE

B. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 46-41-00-610-811-A	Get access to the ALNA Graphical User Interface (GUI) - Maintenance Access - with Multi-Purpose Flight-Attendant Panel (MP-FAP)

3. Job Set-up
Subtask 46-41-00-861-063-C ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Access the ALNA Graphical User Interface (GUI) - Maintenance Access - via Multi-Purpose Flight-Attendant Panel (MP-FAP) (Ref. AMM TASK 46-41-00-610-811).

Subtask 46-41-00-865-065-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
2000VU	WAP	27MH	D07
2000VU	CINS-HESU	21RF	E02

4. Procedure
Subtask 46-41-00-970-060-C ** ON A/C NOT FOR ALL

A. Forced Load of the CINS platform parameter

NOTE: You can do this procedure at the Multi-Purpose Flight-Attendant Panel (MP-FAP) or on the LAPTOP - FOR GSM ALNA MAINTENANCE. The procedures at the MP-FAP and on the maintenance laptop are the same.

NOTE: The table that follows gives the procedure for the MP-FAP.

ACTION	RESULT
In the cabin, at the MP-FAP:	In the cabin, on the MP-FAP display:
1.Touch the "DATA LOADING" icon.	An hourglass symbol shows adjacent to the mouse cursor until the data comes into view. The "DATA LOADING" page shows.
2.Select the "LRU Loading" tab.	The "LRU Loading" tab shows.
3.On the left upper corner touch on the arrow right to the hardware field.	A drop down menu shows with all LRUs.
4.Touch the "HESU" icon.	The "Software load for HESU" shows.
5.Touch the "CINS-PARAMETER" icon.	The load becomes marked in blue and the install button becomes active.
6.Touch the "INSTALL" icon.	A pop-up window shows the message "Start software installation".
7.Touch the "OK" icon to confirm.	The "Software Installation page" shows. The message "Software installation was successful" shows.
8.Touch the "OK" icon to confirm.

5. Close-up
Subtask 46-41-00-862-063-C ** ON A/C NOT FOR ALL

A. Put the aircraft back to its initial configuration.
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2) Touch the "LOGOFF" icon.

NOTE: It is not necessary to log off, if you continue with a different test procedure.

(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.02 06:26:12 UTC