Download of the Configuration Report to the USB flash drive

TASK 46-41-00-720-820-A
Download of the Configuration Report to the USB flash drive

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	USB FLASH DRIVE, MIN. 2GB CAPACITY

B. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 46-41-00-610-811-A	Get access to the ALNA Graphical User Interface (GUI) - Maintenance Access - with Multi-Purpose Flight-Attendant Panel (MP-FAP)

3. Job Set-up
Subtask 46-41-00-861-143-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Access the ALNA Graphical User Interface (GUI) - Maintenance Access - via Multi-Purpose Flight-Attendant Panel (MP-FAP) (Ref. AMM TASK 46-41-00-610-811).

Subtask 46-41-00-865-154-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
2000VU	WAP	27MH	D07
2000VU	CINS-HESU	21RF	E02

4. Procedure
Subtask 46-41-00-720-070-A ** ON A/C NOT FOR ALL

A. Download the Configuration Report to the USB flash drive

NOTE: You can do this procedure at the Multi-Purpose Flight-Attendant Panel (MP-FAP) or on the LAPTOP - FOR GSM ALNA MAINTENANCE. The procedures at the MP-FAP and on the maintenance laptop are the same. The table that follows gives the procedure for the MP-FAP.

NOTE: It is recommended to use a high speed USB flash drive 2.0 with a minimum capacity of 2GB.

ACTION	RESULT
In the cabin, at the MP-FAP:	In the cabin, on the MP-FAP display:
1.Put the USB FLASH DRIVE, MIN. 2GB CAPACITY into the USB port of the MP-FAP.
2.Touch the "SYSTEM IDENTIFICATION" icon.	The "SYSTEM IDENTIFICATION" page shows. All the FINs, the related components, the part numbers and the serial numbers show.
3.Touch the "EXPORT" icon.	The "EXPORT PROGRESS" pop-up window shows.
4.Wait until the export is completed.	The "EXPORT COMPLETED SUCCESFULLY" pop-up window shows.
5.Touch the "OK" icon.	The "EXPORT COMPLETED SUCCESSFULLY" pop-up window closes.
6.Remove the USB flash drive.

5. Close-up
Subtask 46-41-00-862-142-A ** ON A/C NOT FOR ALL

A. Put the aircraft back to its initial configuration.
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2) Touch the "LOGOFF" icon.

NOTE: It is not necessary to log off, if you continue with a different test procedure.

(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.02 06:26:14 UTC