Functional End-to-End Test for Internet

TASK 46-41-00-720-810-A
Functional End-to-End Test for Internet

ZONE: 200

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	LAPTOP - FOR GSM ALNA MAINTENANCE

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
200	UPPER HALF FUSELAGE

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 31-21-00-750-002-A	Procedure to Set the Clock
TASK 34-10-00-860-004-A	Inertial Reference (IR) Alignment-Procedure
TASK 34-10-00-860-004-A-01	Automatic Inertial Reference (IR) Alignment-Procedure
TASK 34-10-00-860-004-A-02	Inertial Reference (IR) Alignment-Procedure to do a Check of the Links between each Flight Management and Guidance Computer (FMGC) and the three Air Data/Inertial Reference Units (ADIRUs)
TASK 46-41-00-610-811-A	Get access to the ALNA Graphical User Interface (GUI) - Maintenance Access - with Multi-Purpose Flight-Attendant Panel (MP-FAP)
TASK 46-41-00-710-804-A	System Monitoring Condition Check

3. Job Set-up
Subtask 46-41-00-861-103-C ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Access the ALNA Graphical User Interface - Maintenance Access - via Multi-Purpose Flight-Attendant Panel (MP-FAP) (Ref. AMM TASK 46-41-00-610-811).
(3) Make sure that:

The Air Data/Inertial Reference-Units (ADIRUs) are ON and aligned (Ref. AMM TASK 34-10-00-860-004).
The "Time and Date" are set (Ref. AMM TASK 31-21-00-750-002).
The "City Pair" is set.
The "Flight Number" is set.
The A/C is outside the hangar, with line-of-sight to the satellite.
The ALNA system operates correctly (Ref. AMM TASK 46-41-00-710-804).

Subtask 46-41-00-865-110-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
2000VU	WAP	27MH	D07
2000VU	CINS-HESU	21RF	E02

4. Procedure
Subtask 46-41-00-720-061-C ** ON A/C NOT FOR ALL

WARNING: DURING THE END-TO-END TEST OF THE ALNA SYSTEM, MAKE SURE THAT THERE ARE NO PERSONS IN A RADIUS OF 29.2 METERS AROUND THE ANTENNA BORESIGHT. THE ANTENNA USES HIGH POWER WHEN IT TRANSMITS AND CAN CAUSE INJURY TO PERSONS.

A. Functional End-to-End Test for Internet

NOTE: You can do this test at the Multi-Purpose Flight-Attendant Panel or on the LAPTOP - FOR GSM ALNA MAINTENANCE. The procedures at the MP-FAP and on the maintenance laptop are the same.

NOTE: To do this procedure a client device with Wi-Fi adapter and web browser is needed, it could be a laptop, tablet or smartphone.

NOTE: The table that follows gives the procedure for the MP-FAP.

ACTION	RESULT
In the cabin, at the MP-FAP:	In the cabin, on the MP-FAP display:
1.Touch the "SYSTEM TEST" icon.	The "SYSTEM TEST" pages comes into view.
2.Select the "CALIBRATION AND FUNCTION TEST" tab.	The "CALIBRATION AND FUNCTION TEST" tab shows.
3.Touch the line "FUNCTIONAL END-TO-END TEST".	The "FUNCTIONAL END-TO-END TEST" is marked in blue.
4.Touch the "START TEST" icon.	The "FUNCTIONAL END-TO-END TEST" page shows.
5.Touch the "ARROW DOWN" icon.	The drop-down menu shows.
6.Touch the "INTERNET" icon.	The "INTERNET TEST" page shows.
7.Touch the "START" icon.	After 3 minutes the start-up is completed. The "TEST" icon becomes active.
8.Touch the "TEST" icon.	The message "THE INTENET SERVICE IS NOW AVAILABLE" shows.
In the cabin, at the passenger seat:	In the cabin, on the maintenance laptop:
9.Start the client device.	The client device boots.
10.Connect the client device to the Wi-Fi network.
11.Open the web browser.	The web browser window shows.
12.Enter the URL "www.google.com".	The Start-Up page shows (http:// portal.inflight.onair.aero).
In the cabin, at the MP-FAP:	In the cabin, on the MP-FAP display:
13.Touch the "NEXT" icon.	A pop-up window with the message "SHOULD THE TEST REALLY BE STOPPED" shows.
14.Touch the "YES" icon to confirm.	The message "SHUTDOWN COMPONENTS IN PROGRESS" shows. The message "SHUTDOWN COMPLETE" shows and the "SHOW RESULTS" icon becomes active.
15.Touch the "SHOW RESULTS" icon.	The "RESULT" page shows.
16.Use the "ARROW" icons to scroll in the results list.	Make sure that the results of all tests are satisfactory.
17.Touch the "NEXT" icon.	The "POST CONDITION" page shows.
18.Touch the "CLOSE" icon.	The "CALIBRATION AND FUNCTION TEST" tab shows.

5. Close-up
Subtask 46-41-00-862-103-C ** ON A/C NOT FOR ALL

A. Put the aircraft back to its initial configuration.
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2) Touch the "LOGOFF" icon.

NOTE: It is not necessary to log off, if you continue with a different test procedure.

(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.02 06:26:14 UTC