Airport Clearance Table (ACT) Loading Procedure

TASK 46-41-00-610-816-A
Airport Clearance Table (ACT) Loading Procedure

ZONE: 220

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	LAPTOP - FOR GSM ALNA MAINTENANCE
No specific	1	USB FLASH DRIVE

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
220	FWD CAB UTILITY AREAS

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 46-41-00-610-811-A	Get access to the ALNA Graphical User Interface (GUI) - Maintenance Access - with Multi-Purpose Flight-Attendant Panel (MP-FAP)

3. Job Set-up
Subtask 46-41-00-860-103-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Access the ALNA Graphical User Interface - Maintenance Access - via Multi-Purpose Flight-Attendant Panel (MP-FAP) (Ref. AMM TASK 46-41-00-610-811).

Subtask 46-41-00-865-173-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
2000VU	CINS-HESU	21RF	E02
2000VU	CINS-RESET-RELAY	20RF	E01

4. Procedure
Subtask 46-41-00-616-053-A ** ON A/C NOT FOR ALL

A. ACT Loading Procedure

NOTE: You can do this procedure at the MP-FAP or on the LAPTOP - FOR GSM ALNA MAINTENANCE. The procedures at the MP-FAP and on the maintenance laptop are the same.

NOTE: The table that follows gives the procedure for the MP-FAP.

ACTION	RESULT
In the cabin, at the MP-FAP:	In the cabin, on the MP-FAP display:
1.Put the USB FLASH DRIVE into the USB port of the MP-FAP and wait for 1 minute. NOTE: The USB FLASH DRIVE must contain a folder with "act_" prefix. This folder must contain the data file and the .xml format file.
2.Touch the "DATA LOADING" icon.	An hourglass symbol shows until the data shows. The "SW LOADING" page comes into view.
3.Select the "ACT LOADING" tab.	A pop-up window to enter the password shows.
4.Enter the password and touch the "OK" icon. NOTE: The default password is "1234".	The "ACT LOADING" page shows.
5.Touch the arrow down icon adjacent to the "Settings to Install" field.	A pop-up window "Setting to Install from" shows.
6.Select one of the available packages.	The "ACT LOADING" page shows with all packages available for installation in the selected package.
7.Touch on the package(s) you will install. NOTE: "ACT LOADING" page shows all ADI and/or CGL, and/or WLM (if equipped) packages available for installation. NOTE: By default all new package(s) is (are) selected (highlighted) for installation.	Selected package(s) is (are) highlighted.
8.Make sure that the columns "Version to Install", "State" and "Current Version" are correct for the selected package(s).
9.Touch the "INSTALL" icon.	A pop-up window to confirm the content load shows.
10.Touch the "OK" icon to start the installation.	A pop-up windows with the installation progress bar comes into view. The estimated installation time shows at the bottom of the screen. A pop-up window with the message "ALL PACKAGES INSTALLED" comes into view. NOTE: It is possible that the estimated time for content loading does not match with the necessary time because of different used technologies for example USB version, CD speed, MP-FAP connection or other.
11.Touch the "OK" icon.	The "ACT LOADING" page shows.
12.Make sure that the columns "Version to Install" and "Current Version" shows the same value and that the state shows as "INSTALLED" with green icon for the installed package.
13.Repeat steps 5 thru 12 for all packages available for installation in the "Setting to Install from" pop-up window.
14.Remove the USB FLASH DRIVE from the MP-FAP.

5. Close-up
Subtask 46-41-00-860-104-A ** ON A/C NOT FOR ALL

A. Put the aircraft back to its initial configuration.
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2) Touch the "LOGOFF" icon.

NOTE: It is not necessary to log off, if you continue with a different test procedure.

(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.02 06:26:11 UTC