DOC AIRBUS | AMM A320FReset of the SATCOM Global Xpress Aviation (GXA) from ALNA Graphical User Interface (GUI)
TASK 46-41-00-600-808-A
Reset of the SATCOM Global Xpress Aviation (GXA) from ALNA Graphical User Interface (GUI)
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
B. Referenced Information
3. Job Set-up
Subtask 46-41-00-861-147-A ** ON A/C NOT FOR ALL
Subtask 46-41-00-600-055-A ** ON A/C NOT FOR ALL
Subtask 46-41-00-862-146-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.02 06:26:11 UTC
Reset of the SATCOM Global Xpress Aviation (GXA) from ALNA Graphical User Interface (GUI)
ZONE: 200
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 200 | UPPER HALF FUSELAGE |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-41-00-861-002-A | Energize the Aircraft Electrical Circuits from the External Power |
| TASK 24-41-00-861-002-A-01 | Energize the Aircraft Electrical Circuits from the APU |
| TASK 24-41-00-861-002-A-02 | Energize the Aircraft Electrical Circuits from Engine 1(2) |
| TASK 24-41-00-862-002-A | De-energize the Aircraft Electrical Circuits Supplied from the External Power |
| TASK 24-41-00-862-002-A-01 | De-energize the Aircraft Electrical Circuits Supplied from the APU |
| TASK 24-41-00-862-002-A-02 | De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2) |
| TASK 46-41-00-610-811-A | Get access to the ALNA Graphical User Interface (GUI) - Maintenance Access - with Multi-Purpose Flight-Attendant Panel (MP-FAP) |
| TASK 46-41-00-860-801-A | Connection of the Maintenance Laptop to the Cabin Plug |
Subtask 46-41-00-861-147-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Access the ALNA Graphical User Interface (GUI) - Maintenance Access - via Multi-Purpose Flight-Attendant Panel (MP-FAP) (Ref. AMM TASK 46-41-00-610-811).
(3) Connect the maintenance laptop to the cabin plug (Ref. AMM TASK 46-41-00-860-801).
Subtask 46-41-00-865-158-A ** ON A/C NOT FOR ALL (1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Access the ALNA Graphical User Interface (GUI) - Maintenance Access - via Multi-Purpose Flight-Attendant Panel (MP-FAP) (Ref. AMM TASK 46-41-00-610-811).
(3) Connect the maintenance laptop to the cabin plug (Ref. AMM TASK 46-41-00-860-801).
B. Make sure that this(these) circuit breaker(s) is(are) closed:
4. Procedure| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 2000VU | WAP | 27MH | D07 |
| 2000VU | CINS-HESU | 21RF | E02 |
Subtask 46-41-00-600-055-A ** ON A/C NOT FOR ALL
A. Reset of the SATCOM (GXA) from GUI
5. Close-upNOTE: You can do this procedure at the Multi-Purpose Flight-Attendant Panel (MP-FAP) or on the LAPTOP - FOR ALNA MAINTENANCE. The procedures are the same.
NOTE: The table that follows gives the procedure for the MP-FAP.
| ACTION | RESULT |
|---|---|
| In the cabin, at the MP-FAP: | In the cabin, on the MP-FAP display: |
| 1.Touch the "SYSTEM MONITORING" icon. |
|
| 2.Touch the "RESET" icon in the line GXA. |
|
| 3.Touch the "OK" icon to confirm the reset. |
|
Subtask 46-41-00-862-146-A ** ON A/C NOT FOR ALL
A. Put the aircraft back to its initial configuration.
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2) Touch the "LOGOFF" icon.
(Ref. AMM TASK 24-41-00-862-002).
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2) Touch the "LOGOFF" icon.
NOTE: It is not necessary to log off, if you continue with a different test procedure.
(3) De-energize the aircraft electrical circuits(Ref. AMM TASK 24-41-00-862-002).