W DOC AIRBUS | AMM A320F

Removal of the Hydraulic Box


TASK 38-12-41-000-004-A
Removal of the Hydraulic Box


ZONE: 200
1. Reason for the Job
Self explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
CAP - BLANKING
No specific
1
CONTAINER 5 L (1.32 USGAL)
No specific
AR
PLUG - BLANKING
No specific
AR
SAFETY CLIP - CIRCUIT BREAKER
No specific
1
WARNING NOTICE(S)
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
200
UPPER HALF FUSELAGE
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 24-42-00-861-001-A
Energize the Ground Service Network from the External Power
TASK 25-45-26-000-001-A
Removal of the Lining
TASK 38-10-00-614-002-A
Depressurization of the Potable Water System
TASK 38-12-41-000-007-A
Removal of the Inline Filters
3. Job Set-up
Subtask 38-12-41-861-052-A ** ON A/C NOT FOR ALL
A. Energize the ground service network
(Ref. AMM TASK 24-42-00-861-001).
Subtask 38-12-41-010-056-A ** ON A/C NOT FOR ALL
B. Get Access
F Electronic Hydraulic Box ** ON A/C NOT FOR ALL
   (1) Get access to the hydraulic box (10) (Ref. AMM TASK 25-45-26-000-001).
Subtask 38-12-41-865-052-A ** ON A/C NOT FOR ALL
C. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
2001VUVACU TOIL SYS-LAV PWR-M34MGA04
2001VUVACU TOIL SYS-LAV PWR-D39MGA03
2001VUVACU TOIL SYS-LAV PWR-L45MGA02
2001VUVACU TOIL SYS-LAV PWR-A32MGA01
Subtask 38-12-41-860-055-A ** ON A/C NOT FOR ALL
D. Aircraft Maintenance Configuration
F Electronic Hydraulic Box ** ON A/C NOT FOR ALL
   (1) Depressurize the potable water system (Ref. AMM TASK 38-10-00-614-002).
   (2) Close the potable water-shutoff valve in the lavatory.
   (3) Put the WARNING NOTICE(S) in position to tell persons not to open the potable-water shutoff valve in the lavatory.
   (4) Put a CONTAINER 5 L (1.32 USGAL) under the hydraulic box (10) to collect unwanted material.
4. Procedure
Subtask 38-12-41-020-053-A ** ON A/C NOT FOR ALL
A. Removal of the Hydraulic Box
CAUTION: MAKE SURE THAT THE ELECTRICAL CONNECTORS ARE CLEAN BEFORE YOU DISCONNECT OR CONNECT THEM. CONTAMINATION ON THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO EQUIPMENT.
   (1) Disconnect the electrical connector (2).
   (2) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
   (3) Remove the screws (6) and the cover (5).
   (4) Remove the inline filters (Ref. AMM TASK 38-12-41-000-007).
   (5) Disconnect the connection (1).
   (6) Put the PLUG-BLANKING in each disconnected line end.
   (7) Remove the screw (7), the washer (8) and disconnect the bonding strap (9).
   (8) Remove the screws (4), the washers (3) and the hydraulic box (10).
[Rev.10 from 2021] 2026.04.02 06:25:40 UTC