Removal of the Bellows
TASK 36-12-42-000-001-A
Removal of the Bellows
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Referenced Information
3. Job Set-up
Subtask 36-12-42-865-050-A ** ON A/C NOT FOR ALL
Subtask 36-12-42-020-050-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.02 06:25:17 UTC
Removal of the Bellows
WARNING:
PUT WARNING NOTICES IN THE COCKPIT BEFORE YOU DO WORK ON THE BLEED AIR SYSTEM TO TELL PERSONS:
- NOT TO OPERATE THE ENGINES
- NOT TO OPERATE THE SLATS
- NOT TO OPERATE THE APU SWITCH.
FIN: 7265HM ** ON A/C NOT FOR ALL
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 3M (10 FT) |
| No specific | AR | CAP - BLANKING |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| No specific | AR | WARNING NOTICE(S) |
| REFERENCE | DESIGNATION |
|---|---|
Subtask 36-12-42-865-050-A ** ON A/C NOT FOR ALL
A. Open, safety and tag this(these) circuit breaker(s):
Subtask 36-12-42-860-050-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR BLEED/X FEED/VALVE/BAT | 2HV | D13 |
| 49VU | AIR BLEED/ENG 1/CTL | 3HA1 | D12 |
| 49VU | AIR BLEED/ENG 1/MONG | 2HA1 | D11 |
| 122VU | AIR BLEED/ENG 2/CTL | 3HA2 | Z23 |
| 122VU | AIR BLEED/ENG 2/MONG | 2HA2 | Z22 |
| 122VU | AIR BLEED/X FEED VALVE/NORM | 1HV | Z20 |
B. Aircraft Maintenance Configuration
(1) Put the WARNING NOTICE(S) in position:
(3) Open the access door 312AR.
4. Procedure(1) Put the WARNING NOTICE(S) in position:
- in the cockpit on the Engine Control Panel 115VU to tell persons not to start the engine(s),
- in the cockpit on the AIR COND Overhead Control Panel 30VU to tell persons not to push in the APU BLEED pushbutton switch,
- on the HP ground connector to tell persons not to pressurize the pneumatic system.
(3) Open the access door 312AR.
Subtask 36-12-42-020-050-A ** ON A/C NOT FOR ALL
A. Removal of the Bellows (7265HM)
(2) Remove the clamp (3).
(3) Loosen the clamps (4) and (6).
(4) Carefully remove the bellows (5) from between the duct sections (1) and (7).
(5) Put a CAP - BLANKING on the open ends of the duct sections (1) and (7).
WARNING:
MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.
(1) Remove the sleeve (2), if installed. (2) Remove the clamp (3).
(3) Loosen the clamps (4) and (6).
(4) Carefully remove the bellows (5) from between the duct sections (1) and (7).
(5) Put a CAP - BLANKING on the open ends of the duct sections (1) and (7).
Bellows (7265HM)