Functional Test of the Sense Line Connected between the Bleed Regulated Pressure-Transducer and the Duct Assy with the Bleed Test Set P/N 99127B03

TASK 36-11-00-720-011-A
Functional Test of the Sense Line Connected between the Bleed Regulated Pressure-Transducer and the Duct Assy with the Bleed Test Set P/N 99127B03

WARNING: MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE PARTS AFTER THE ENGINE SHUTDOWN. USE APPLICABLE THERMAL GLOVES. THE ENGINE PARTS CAN STAY HOT FOR ONE HOUR AFTER SHUTDOWN AND CAN BURN YOU.

FIN: 8HA1 ** ON A/C NOT FOR ALL
FIN: 8HA2 ** ON A/C NOT FOR ALL

1. Reason for the Job
To make sure that there are no leaks on the sense line Connected between the Bleed Regulated Pressure-Transducer and the Duct Assy.

NOTE: You can use bleed test set P/N 99127B04 as an alternative to bleed test set P/N 99127B03.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 1M(3 FT)
No specific	1	SUPPLY - 28 VDC, ELECTRICAL
No specific	AR	WARNING NOTICE(S)
No specific	Torque wrench: range to between 1.1 and 0.9 m.daN (97.35 and 79.65 lbf.in )
No specific	Torque wrench: range to between 1.76 and 1.44 m.daN (12.98 and 10.62 lbf.ft )
99127-231	1	TEST SET BLEED - KIT
99127B03	1	BLEED TEST SET

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
191MB
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 451AL
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 461AL

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 71-13-00-010-010-A	Opening of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 71-13-00-010-040-A	Opening of the Fan Cowl Doors
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors
TASK 71-13-00-410-010-A	Closing of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 71-13-00-410-040-A	Closing of the Fan Cowl Doors
TASK 71-13-00-410-040-B	Closing of the Fan Cowl Doors
TASK 78-30-00-040-012-A	Deactivation of the Thrust Reverser Hydraulic Control Unit (HCU) for Ground Maintenance
TASK 78-30-00-081-041-A	Make the Thrust Reverser Serviceable after Maintenance
TASK 78-30-00-081-041-B	Make the Thrust Reverser Serviceable after Maintenance
TASK 78-30-00-440-012-A	Re-activation of the Thrust Reverser Hydraulic Control Unit (HCU) after Ground Maintenance
TASK 78-30-00-481-041-A	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-30-00-481-041-B	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-32-00-010-010-A	Opening of the Thrust Reverser Halves
TASK 78-32-00-410-010-A	Closing of the Thrust Reverser Halves
TASK 78-36-00-010-040-A	Opening of the Thrust Reverser Doors
TASK 78-36-00-010-040-B	Opening of the Thrust Reverser Doors
TASK 78-36-00-410-040-A	Closing of the Thrust Reverser Doors
TASK 78-36-00-410-040-B	Closing of the Thrust Reverser Doors
Functional Test of the Sense Line Connected between the Bleed Regulated Pressure-Transducer and the Duct Assy with the Bleed Test Set P/N 99127B03

3. Job Set-up
Subtask 36-11-00-861-088-A ** ON A/C NOT FOR ALL

A. Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).

Subtask 36-11-00-941-101-A ** ON A/C NOT FOR ALL

B. Safety Precautions
(1) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(2) On the AIR COND panel 30VU:

Make sure that the ENG 1(2) BLEED pushbutton switch is released (the OFF legend is on).
Make sure that the APU BLEED pushbutton switch is released (the ON legend is off).
Put a WARNING NOTICE(S) in position to tell persons not to operate the pneumatic system.

(3) On the ENG panel 115VU:

Put a WARNING NOTICE(S) in position to tell persons not to start the engine 1(2).

(4) On the HP ground connector:

Put a WARNING NOTICE(S) in position to tell persons not to pressurize the pneumatic system.

(5) On the ENG section of the maintenance panel 50VU:

Make sure that the ON legend of the ENG/FADEC GND PWR 1(2) pushbutton switch is off.
Put a WARNING NOTICE(S) in position to tell persons not to energize the FADEC 1(2).

Subtask 36-11-00-010-095-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.
(2) Open the access door 191MB.
(3) Put the ACCESS PLATFORM 1M(3 FT) in position below the engine.

Subtask 36-11-00-040-068-A ** ON A/C NOT FOR ALL

D. Deactivation of the Thrust Reverser

WARNING: MAKE SURE THAT THE THRUST REVERSER HYDRAULIC CONTROL UNIT (HCU) IS DEACTIVATED BEFORE YOU DO WORK ON OR AROUND THE THRUST REVERSER. IF THE HCU IS NOT DEACTIVATED, THERE IS A RISK OF UNWANTED THRUST REVERSER OPERATION WHICH CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

(1) Make the thrust reverser unserviceable for maintenance (Ref. AMM TASK 78-30-00-481-041).

Subtask 36-11-00-010-096-A ** ON A/C NOT FOR ALL

E. Open the left thrust-reverser door (Ref. AMM TASK 78-36-00-010-040):
(1) FOR [1000EM1] (ENGINE-1)
451AL
(2) FOR [1000EM2] (ENGINE-2)
461AL.

Subtask 36-11-00-010-095-B ** ON A/C NOT FOR ALL

F. Get Access
(1) Open the fan cowls (Ref. AMM TASK 71-13-00-010-010):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.
(2) Open the access door 191MB.
(3) Put the ACCESS PLATFORM 1M(3 FT) in position below the engine.

Subtask 36-11-00-040-068-B ** ON A/C NOT FOR ALL

G. Deactivation of the Thrust Reverser

(1) Do the deactivation of the Thrust-Reverser Hydraulic Control-Unit (HCU) (Ref. AMM TASK 78-30-00-040-012).

Subtask 36-11-00-010-096-B ** ON A/C NOT FOR ALL

H. Open the left thrust-reverser half (Ref. AMM TASK 78-32-00-010-010):
(1) FOR [1000EM1] (ENGINE-1)
451AL
(2) FOR [1000EM2] (ENGINE-2)
461AL.

Subtask 36-11-00-010-095-C ** ON A/C NOT FOR ALL

I. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.
(2) Open the access door 191MB.
(3) Put the ACCESS PLATFORM 1M(3 FT) in position below the engine.

Subtask 36-11-00-040-068-C ** ON A/C NOT FOR ALL

J. Deactivation of the Thrust Reverser

(1) Make the thrust reverser unserviceable for maintenance (Ref. AMM TASK 78-30-00-481-041).

Subtask 36-11-00-010-096-C ** ON A/C NOT FOR ALL

K. Open the left thrust-reverser door (Ref. AMM TASK 78-36-00-010-040):
(1) FOR [1000EM1] (ENGINE-1)
451AL
(2) FOR [1000EM2] (ENGINE-2)
461AL.

4. Procedure
Subtask 36-11-00-480-056-A ** ON A/C NOT FOR ALL

A. Installation of the Tool
(1) Connect the 99127B03 BLEED TEST SET (T01) to the sense line tester (T10) as shown in the figure.

Functional Test of the Sense Line Connected between the Bleed Regulated Pressure-Transducer and the Duct Assy with the Bleed Test Set P/N 99127B03 ** ON A/C NOT FOR ALL

NOTE: Use the 99127-231 TEST SET BLEED - KIT to do this test.

NOTE: Set the pressure gauge (5) to ON. The pressure value shown on the LCD screen must be equal to 0 psi (0 bar). If it is not equal to 0 psi (0 bar), push the ON button for 10 seconds.

(2) Connect the 28VDC electrical cord (T03) between the electrical inlet (11) of the 99127B03 BLEED TEST SET (T01) and an external SUPPLY - 28 VDC, ELECTRICAL:

Start the SUPPLY - 28 VDC, ELECTRICAL.

CAUTION: USE A SECOND WRENCH TO APPLY COUNTERTORQUE TO THE UNION WHEN YOU DISCONNECT/CONNECT THE PNEUMATIC LINES ON UNIONS.

(3) Disconnection of the sense line:

NOTE: Loosen the pneumatic union a quarter turn with a spanner. Then shake the sense line with your hand to prevent cross thread damage to the pneumatic union.
To prevent damage to the fitting end of the sense line, turn the union with your hand and not with a spanner.

(a) Disconnect the sense line from the union of the duct assy.
(4) Put the blanking plug (T16) on the duct assy.
(5) Connection of the sense line adaptor (T20):

CAUTION: MAKE SURE THE ADAPTOR T20 IS CORRECTLY TIGHTENED ON THE SENSE LINE.

(a) Connect the sense line adaptor (T20) to the sense line union and TORQUE to between 1.1 and 0.9 m.daN (97.35 and 79.65 lbf.in )

.
(6) Open the pressure-source shut-off valve slowly and pressurize the 99127B03 BLEED TEST SET (T01) to 30 psi (2.07 bar).

Subtask 36-11-00-720-061-A ** ON A/C NOT FOR ALL

B. Test

ACTION	RESULT
1.On the sense line tester: Open the valves 1 and 2.	On the sense line tester: The two valves are aligned with the pneumatic ducts.
2.On the test set: Set the Blue valve (7) to ON.
3.On the test set: With the pressure gauge A (3), increase the pressure to between 21 and 22 psi (1.45 and 1.52 bar).	On the test set: The pressure value shows on the LCD (5).
4.On the sense line tester: Close the valve 1.	On the sense line tester: The valve 1 is not aligned with the pneumatic duct.
	On the test set: The pressure value on the LCD (5) must be equal to the input pressure value (with a tolerance of +/- 0.2 psi (+/- 0.01 bar).

Subtask 36-11-00-080-054-A ** ON A/C NOT FOR ALL

C. Removal of the Tool
(1) With the pressure gauge A (3), decrease the pressure to 0 psi (0 bar).
(2) Stop the SUPPLY - 28 VDC, ELECTRICAL.
(3) Disconnect the 28VDC electrical cord (T03) from the electrical inlet (11) of the 99127B03 BLEED TEST SET (T01) and the external SUPPLY - 28 VDC, ELECTRICAL.
(4) Disconnect and remove the 99127B03 BLEED TEST SET (T01), the sense line tester (T10) and the sense line adaptor (T20) from the sense line union.
(5) Remove the blanking plug (T16) from the duct assy.

CAUTION: USE A SECOND WRENCH TO APPLY COUNTERTORQUE TO THE UNION WHEN YOU DISCONNECT/CONNECT THE PNEUMATIC LINES ON UNIONS.

(6) Connection of the sense line:

NOTE: There must be no grease or oil on the pneumatic and sense line unions.

(a) Connect the sense line to the union of the duct assy.

NOTE: To prevent damage to the fitting end of the sense line, turn the union with your hand and not with a spanner.

(b) Do the double torque method on the union of the sense line to between 1.76 and 1.44 m.daN (12.98 and 10.62 lbf.ft )

NOTE: Double torque method: Torque a first time the union of the sense line to the given value. Loosen the union of the sense line a quarter of a turn. Then torque a second time the union to the given value.

5. Close-up
Subtask 36-11-00-410-095-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the left thrust-reverser door (Ref. AMM TASK 78-36-00-410-040):
(a) FOR [1000EM1] (ENGINE-1)
451AL
(b) FOR [1000EM2] (ENGINE-2)
461AL.

Subtask 36-11-00-440-068-A ** ON A/C NOT FOR ALL

B. Make the thrust reverser serviceable after maintenance (Ref. AMM TASK 78-30-00-081-041).

Subtask 36-11-00-410-096-A ** ON A/C NOT FOR ALL

C. Close Access
(1) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.
(2) Close the access door 191MB.
(3) Remove the access platform(s).
(4) Remove the WARNING NOTICE(S).

Subtask 36-11-00-410-095-B ** ON A/C NOT FOR ALL

D. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the left thrust-reverser half (Ref. AMM TASK 78-32-00-410-010):
(a) FOR [1000EM1] (ENGINE-1)
451AL
(b) FOR [1000EM2] (ENGINE-2)
461AL.

Subtask 36-11-00-440-068-B ** ON A/C NOT FOR ALL

E. Do the re-activation of the thrust reverser HCU (Ref. AMM TASK 78-30-00-440-012).

Subtask 36-11-00-410-096-B ** ON A/C NOT FOR ALL

F. Close Access
(1) Close the fan cowls (Ref. AMM TASK 71-13-00-410-010):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.
(2) Close the access door 191MB.
(3) Remove the WARNING NOTICE(S).
(4) Remove the access platform(s).

Subtask 36-11-00-410-095-C ** ON A/C NOT FOR ALL

G. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the left thrust-reverser door (Ref. AMM TASK 78-36-00-410-040):
(a) FOR [1000EM1] (ENGINE-1)
451AL
(b) FOR [1000EM2] (ENGINE-2)
461AL.

Subtask 36-11-00-440-068-C ** ON A/C NOT FOR ALL

H. Make the thrust reverser serviceable after maintenance (Ref. AMM TASK 78-30-00-081-041).

Subtask 36-11-00-410-096-C ** ON A/C NOT FOR ALL

I. Close Access
(1) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.
(2) Close the access door 191MB.
(3) Remove the access platform(s).
(4) Remove the WARNING NOTICE(S).

Subtask 36-11-00-862-083-A ** ON A/C NOT FOR ALL

J. De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.01 01:07:03 UTC