Uploading of the Bleed Monitoring Computer (BMC) Data

TASK 36-11-00-610-801-A
Uploading of the Bleed Monitoring Computer (BMC) Data

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 31-38-00-610-804-A	Onboard Software Uploading Procedure
TASK 36-11-00-740-802-A	BITE Test of the Engine Bleed Air System (EBAS) (System Test)

3. Job Set-up
Subtask 36-11-00-861-135-A ** ON A/C NOT FOR ALL

A. Energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-861-002).

Subtask 36-11-00-865-122-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	AUTO FLT/MCDU/1	11CA1	B01
** ON A/C NOT FOR ALL
49VU	L/G/LGCIU/SYS1/NORM	1GA	C09
49VU	AIR BLEED/ENG 2/MONG	3HA2	D12
49VU	AIR BLEED/ENG 1/CTL	2HA1	D11
** ON A/C NOT FOR ALL
49VU	AUTO FLT/MCDU/1	11CA1	H07
** ON A/C NOT FOR ALL
121VU	AUTO FLT/MCDU/2	11CA2	N20
122VU	AIR BLEED/ENG 1/MONG	3HA1	Z23
122VU	AIR BLEED/ENG 2/CTL	2HA2	Z22

Subtask 36-11-00-860-107-A ** ON A/C NOT FOR ALL

C. Make sure that the aircraft is in the GROUND configuration:

ACTION	RESULT
1.On the ECAM control panel: Press the pushbutton to call the BLEED page.	ON the SD: The BLEED page is shown.
2.Make sure that the GND indication is displayed.	GND is displayed in white in the middle area of the page.

Subtask 36-11-00-740-051-A ** ON A/C NOT FOR ALL

D. Check the P/N updated
(1) Do the LRU identification check
(a) Get access to LRU ident page:
1 Select on MCDU the sequence that follows:

MCDU MENU->CFDS->SYSTEM REPORT/TEST->PAGE 2/2->AIR BLEED->BMC1(2)->LRU IDENT.

(2) Make sure that the installed BMC software P/N shown on the LRU IDENTIFICATION page is not the same as the BMC software P/N written on the front face of the new CD-ROM to load.

Subtask 36-11-00-740-051-B ** ON A/C NOT FOR ALL

D. Check of the Part Number (P/N) update
(1) On the MCDU, get access to Line Replaceable Unit (LRU) IDENT page as follows:
(a) MCDU MENU->CFDS->SYSTEM REPORT/TEST->PAGE 2/2->AIR BLEED->BMC1(2)->LRU IDENT.
(2) Make sure that the installed BMC software P/N shown on the LRU IDENTIFICATION page is not same as the P/N requested to be installed with the work order.

4. Procedure
Subtask 36-11-00-970-050-A ** ON A/C NOT FOR ALL

A. Uploading Procedure

NOTE: The two BMCs are uploaded at the same time, BMC1 is directly uploaded through the DLRB and BMC2 is uploaded through the X-TALK from BMC1.

(1) Upload the BMC software (Ref. AMM TASK 31-38-00-610-804).

Subtask 36-11-00-280-051-A ** ON A/C NOT FOR ALL

B. Check the P/N updated
(1) Do the LRU identification check
(a) Get access to LRU ident page:
1 Select on MCDU the sequence that follows:

MCDU MENU->CFDS->SYSTEM REPORT/TEST->PAGE 2/2->AIR BLEED->BMC1(2)->LRU IDENT.

(2) Make sure that the installed BMC software P/N shown on the LRU IDENTIFICATION page is the same as the BMC software P/N written on the front face of the new CD-ROM just loaded.

Subtask 36-11-00-970-050-B ** ON A/C NOT FOR ALL

C. Uploading Procedure
(1) Upload the BMC software (Ref. AMM TASK 31-38-00-610-804).

Subtask 36-11-00-280-051-B ** ON A/C NOT FOR ALL

D. Check of the P/N updated
(1) On the MCDU, get access to LRU IDENT page as follows:
(a) MCDU MENU->CFDS->SYSTEM REPORT/TEST->PAGE 2/2->AIR BLEED->BMC1(2)->LRU IDENT.
(2) Make sure that the installed BMC software P/N shown on the LRU IDENTIFICATION page is same as the P/N requested with the work order.

Subtask 36-11-00-740-058-A ** ON A/C NOT FOR ALL

E. BITE Test of the EBAS
(1) Do the BITE test of the EBAS (Ref. AMM TASK 36-11-00-740-802).

5. Close-up
Subtask 36-11-00-860-106-A ** ON A/C NOT FOR ALL

A. Put the aircraft back to its initial configuration.
(1) On the MCDU, push the MCDU MENU key to get the MCDU MENU page.
(2) Put the CD-ROM back into the cockpit storage-box.

Subtask 36-11-00-860-106-B ** ON A/C NOT FOR ALL

A. Put the aircraft back to its initial configuration.
(1) On the MCDU, push the MCDU MENU key to get the MCDU MENU page.

Subtask 36-11-00-862-120-A ** ON A/C NOT FOR ALL

B. De-energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.01 01:06:16 UTC