Reset of the Radio Altimeter (RA)
TASK 34-42-00-860-801-A
Reset of the Radio Altimeter (RA)
1. Reason for the Job
To do a reset of the RA.
2. Job Set-up Information
A. Referenced Information
3. Job Set-up
Subtask 34-42-00-860-058-A
Subtask 34-42-00-860-059-A
Subtask 34-42-00-860-060-A
[Rev.10 from 2021]
2026.04.02 06:23:23 UTC
Reset of the Radio Altimeter (RA)
1. Reason for the Job
To do a reset of the RA.
2. Job Set-up Information
A. Referenced Information
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-41-00-862-002-A | De-energize the Aircraft Electrical Circuits Supplied from the External Power |
| TASK 24-41-00-862-002-A-01 | De-energize the Aircraft Electrical Circuits Supplied from the APU |
| TASK 24-41-00-862-002-A-02 | De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2) |
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 31-60-00-860-001-A | EIS Start Procedure |
| TASK 31-60-00-860-002-A | EIS Stop Procedure |
Subtask 34-42-00-860-058-A
A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-42-00-861-001).
(2) Do the EIS start procedure (upper ECAM DU and lower ECAM DU only)
(Ref. AMM TASK 31-60-00-860-001).
Subtask 34-42-00-865-062-A (1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-42-00-861-001).
(2) Do the EIS start procedure (upper ECAM DU and lower ECAM DU only)
(Ref. AMM TASK 31-60-00-860-001).
B. Make sure that this(these) circuit breaker(s) is(are) closed:
4. Procedure| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C ALL | |||
| FOR FIN: 2SA1 (XCVRRA, 1) | |||
| 121VU | COM NAV/RAD ALTM/1 | 1SA1 | K11 |
| FOR FIN: 2SA2 (XCVRRA, 2) | |||
| 121VU | COM NAV/RAD ALTM/2 | 1SA2 | K12 |
Subtask 34-42-00-860-059-A
A. Reset of the RA
5. Close-upNOTE: This test is for RA1. For RA2, you can use the indications given in parentheses.
| ACTION | RESULT |
|---|---|
| 1.On rear C/B panel 121VU: | On the upper ECAM DU: |
|
|
| 2.On rear C/B panel 121VU: | On the upper ECAM DU: |
|
|
Subtask 34-42-00-860-060-A
A. Put the aircraft back to its initial configuration.
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Do the EIS stop procedure
(Ref. AMM TASK 31-60-00-860-002).
(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Do the EIS stop procedure
(Ref. AMM TASK 31-60-00-860-002).
(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).