DOC AIRBUS | AMM A320FADIRS - Check of all Flight Control Accelerometers for Correct Operation
TASK 34-10-00-040-002-A
ADIRS - Check of all Flight Control Accelerometers for Correct Operation
1. Reason for the Job
MMEL 34-10-01 ADIRS (FAA only).
2. Job Set-up Information
A. Work Zones and Access Panels
B. Referenced Information
3. Job Set-up
Subtask 34-10-00-860-077-A
Subtask 34-10-00-040-050-A
Subtask 34-10-00-860-078-A
[Rev.10 from 2021]
2026.04.02 06:23:00 UTC
ADIRS - Check of all Flight Control Accelerometers for Correct Operation
1. Reason for the Job
MMEL 34-10-01 ADIRS (FAA only).
2. Job Set-up Information
A. Work Zones and Access Panels
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 210 | CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-41-00-861-002-A | Energize the Aircraft Electrical Circuits from the External Power |
| TASK 24-41-00-861-002-A-01 | Energize the Aircraft Electrical Circuits from the APU |
| TASK 24-41-00-861-002-A-02 | Energize the Aircraft Electrical Circuits from Engine 1(2) |
| TASK 24-41-00-862-002-A | De-energize the Aircraft Electrical Circuits Supplied from the External Power |
| TASK 24-41-00-862-002-A-01 | De-energize the Aircraft Electrical Circuits Supplied from the APU |
| TASK 24-41-00-862-002-A-02 | De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2) |
| TASK 27-96-00-740-001-A | BITE Test of the EFCS (Ground Scanning) |
| TASK 31-60-00-860-001-A | EIS Start Procedure |
| TASK 31-60-00-860-002-A | EIS Stop Procedure |
Subtask 34-10-00-860-077-A
A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Do the EIS start procedure (upper ECAM DU and lower ECAM DU only)
(Ref. AMM TASK 31-60-00-860-001).
(3) On the center pedestal, on the ECAM control panel, push the STS key (on the lower ECAM DU, the STATUS page comes into view).
4. Procedure(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Do the EIS start procedure (upper ECAM DU and lower ECAM DU only)
(Ref. AMM TASK 31-60-00-860-001).
(3) On the center pedestal, on the ECAM control panel, push the STS key (on the lower ECAM DU, the STATUS page comes into view).
Subtask 34-10-00-040-050-A
A. If there is the F/CTL maintenance status:
(1) Do the BITE test of the EFCS (Ground Scanning) (Ref. AMM TASK 27-96-00-740-001).
(2) Make sure that there are no maintenance messages related to the flight control accelerometers 12CE1, 12CE2, 12CE3 and 12CE4.
5. Close-up(1) Do the BITE test of the EFCS (Ground Scanning) (Ref. AMM TASK 27-96-00-740-001).
(2) Make sure that there are no maintenance messages related to the flight control accelerometers 12CE1, 12CE2, 12CE3 and 12CE4.
Subtask 34-10-00-860-078-A
A. Put the aircraft back to its initial configuration.
(1) Do the EIS stop procedure
(Ref. AMM TASK 31-60-00-860-002).
(2) Make an entry in the logbook.
(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).
(1) Do the EIS stop procedure
(Ref. AMM TASK 31-60-00-860-002).
(2) Make an entry in the logbook.
(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).