Removal of the Service Area Light
TASK 33-31-11-000-002-A
Removal of the Service Area Light
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 33-31-11-865-068-A
Subtask 33-31-11-020-051-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 00:54:14 UTC
Removal of the Service Area Light
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE |
| No specific | AR | CAP - BLANKING |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 312AR |
| REFERENCE | DESIGNATION |
|---|---|
Subtask 33-31-11-865-068-A
A. Open, safety and tag this(these) circuit breaker(s):
Subtask 33-31-11-010-051-A | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 2001VU | LIGHT-SEC19 | 1LJ | E07 |
| ** ON A/C NOT FOR ALL | |||
| 2001VU | LIGHT/SEC19 | 1LJ | E07 |
B. Get Access
(1) Put a warning notice in the cockpit to tell persons not to operate the flight controls.
(2) Put the ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE in position in the Zone 312.
(3) Open the access door 312AR.
(4) Set the switch 3LJ at Zone 312 to the OFF position.
4. Procedure(1) Put a warning notice in the cockpit to tell persons not to operate the flight controls.
(2) Put the ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE in position in the Zone 312.
(3) Open the access door 312AR.
(4) Set the switch 3LJ at Zone 312 to the OFF position.
Subtask 33-31-11-020-051-A ** ON A/C NOT FOR ALL
A. Removal of the Service Area Light and the Lamp
(1) Remove the lamp:
(a) Remove the screws (12), the grid-screen (7), the lens (8) and the seal (9) from the housing (11).
(b) Remove the lamp (10).
(2) Remove the service area light:
(a) Remove the screws (6), the washers (5) and hold the service area light (4) to get access to the electrical connections (1).
(b) Remove the nuts (3), the washers (2) and the electrical connections (1).
(c) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(d) Remove the service area light (4).
Subtask 33-31-11-020-051-B ** ON A/C NOT FOR ALL (1) Remove the lamp:
(a) Remove the screws (12), the grid-screen (7), the lens (8) and the seal (9) from the housing (11).
(b) Remove the lamp (10).
(2) Remove the service area light:
(a) Remove the screws (6), the washers (5) and hold the service area light (4) to get access to the electrical connections (1).
(b) Remove the nuts (3), the washers (2) and the electrical connections (1).
(c) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(d) Remove the service area light (4).
A. Removal of the Service Area Light
(1) Remove the screws (1) with the washers (2) and hold the service area light (3) to get access to the electrical connectors (5) an (6).
(2) Disconnect the electrical connectors (5) and (6).
(3) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(4) Remove the service area light (3).
(1) Remove the screws (1) with the washers (2) and hold the service area light (3) to get access to the electrical connectors (5) an (6).
(2) Disconnect the electrical connectors (5) and (6).
(3) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(4) Remove the service area light (3).
Service Area Light