DOC AIRBUS | AMM A320FInstallation of the Floor Light
TASK 33-24-12-400-806-A
Installation of the Floor Light
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Referenced Information
3. Job Set-up
Subtask 33-24-12-860-064-A ** ON A/C NOT FOR ALL
Subtask 33-24-12-420-056-A ** ON A/C NOT FOR ALL
Subtask 33-24-12-860-065-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 00:53:47 UTC
Installation of the Floor Light
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | TIE WRAP |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.06CDD1) | Silicone Adhesive Sealant-Solvant Resistant One part - |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-41-00-861-002-A | Energize the Aircraft Electrical Circuits from the External Power |
| TASK 24-41-00-861-002-A-01 | Energize the Aircraft Electrical Circuits from the APU |
| TASK 24-41-00-861-002-A-02 | Energize the Aircraft Electrical Circuits from Engine 1(2) |
| TASK 24-41-00-862-002-A | De-energize the Aircraft Electrical Circuits Supplied from the External Power |
| TASK 24-41-00-862-002-A-01 | De-energize the Aircraft Electrical Circuits Supplied from the APU |
| TASK 24-41-00-862-002-A-02 | De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2) |
| TASK 33-24-00-710-001-A | Operational Test of the Lavatory Lighting LQ |
Floor LightSubtask 33-24-12-860-064-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Make sure that the aircraft electrical circuits are energized (Ref. AMM TASK 24-41-00-861-002).
(2) In the Spaceflex lavatory:
(a) FOR [53LQ13] (ACCENT LIGHT), [55LQ6] (ACCENT LIGHT)
1 Make sure that the cabinet door is open.
Subtask 33-24-12-865-071-A ** ON A/C NOT FOR ALL (1) Make sure that the aircraft electrical circuits are energized (Ref. AMM TASK 24-41-00-861-002).
(2) In the Spaceflex lavatory:
(a) FOR [53LQ13] (ACCENT LIGHT), [55LQ6] (ACCENT LIGHT)
1 Make sure that the cabinet door is open.
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
4. Procedure| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H07 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H05 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LAV FWD & MID-OCCUPIED | 1WJ | F01 |
| 2000VU | LIGHT-LAV | 1LQ | J01 |
| 2001VU | LAVATORY AFT-OCCUPIED | 11WJ | B04 |
Subtask 33-24-12-420-056-A ** ON A/C NOT FOR ALL
A. Install the Floor Light in the Spaceflex Lavatory
(1) Put the floor light (4) in position and push it until all the clamps (5) engage.
(2) Remove the CAP-BLANKING from each electrical connector and receptacle.
(4) Put the cable (1) in position and install the new TIE WRAP(S) (2).
(5) Hold the shroud (6) in the correct installation position and install the washers (7) and the screws (8).
(6) Fill the opening (9) with the Silicone Adhesive Sealant-Solvant Resistant One part - (Material No.06CDD1) .
Subtask 33-24-12-410-059-A ** ON A/C NOT FOR ALL (1) Put the floor light (4) in position and push it until all the clamps (5) engage.
(2) Remove the CAP-BLANKING from each electrical connector and receptacle.
CAUTION:
REFER TO THE MATCH MARKS MADE DURING THE REMOVAL WHEN YOU CONNECT THE ELECTRICAL WIRES.
INCORRECT CONNECTION OF THE WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
CAUTION:
MAKE SURE THAT THE ELECTRICAL CONNECTORS ARE CLEAN BEFORE YOU DISCONNECT OR CONNECT THEM. CONTAMINATION ON THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO EQUIPMENT.
(3) Connect the electrical connector (3). (4) Put the cable (1) in position and install the new TIE WRAP(S) (2).
(5) Hold the shroud (6) in the correct installation position and install the washers (7) and the screws (8).
(6) Fill the opening (9) with the Silicone Adhesive Sealant-Solvant Resistant One part - (Material No.06CDD1) .
B. Close Access
(1) Close Access to the Floor Light in the Spaceflex lavatory:
(a) FOR [53LQ13] (ACCENT LIGHT), [55LQ6] (ACCENT LIGHT)
1 Close the cabinet door.
Subtask 33-24-12-865-072-A ** ON A/C NOT FOR ALL (1) Close Access to the Floor Light in the Spaceflex lavatory:
(a) FOR [53LQ13] (ACCENT LIGHT), [55LQ6] (ACCENT LIGHT)
1 Close the cabinet door.
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
Subtask 33-24-12-710-056-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H07 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H05 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LAV FWD & MID-OCCUPIED | 1WJ | F01 |
| 2000VU | LIGHT-LAV | 1LQ | J01 |
| 2001VU | LAVATORY AFT-OCCUPIED | 11WJ | B04 |
D. Operational Test
(1) Do the operational test of the lavatory lighting (Ref. AMM TASK 33-24-00-710-001).
5. Close-up(1) Do the operational test of the lavatory lighting (Ref. AMM TASK 33-24-00-710-001).
Subtask 33-24-12-860-065-A ** ON A/C NOT FOR ALL
A. Put the aircraft back to its initial configuration.
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2) Make sure that the work area is clean and clear of tools and other items.
(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2) Make sure that the work area is clean and clear of tools and other items.
(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).