DOC AIRBUS | AMM A320FInstallation of the Accent Mirror Light
TASK 33-24-12-400-804-A
Installation of the Accent Mirror Light
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Referenced Information
3. Job Set-up
Subtask 33-24-12-860-058-A ** ON A/C NOT FOR ALL
Subtask 33-24-12-420-054-A ** ON A/C NOT FOR ALL
Subtask 33-24-12-860-059-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 00:53:42 UTC
Installation of the Accent Mirror Light
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ELEC CONTACTS INSERTION EXTRACTION TOOL M15570-20 |
| No specific | AR | TIE WRAP |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-41-00-861-002-A | Energize the Aircraft Electrical Circuits from the External Power |
| TASK 24-41-00-861-002-A-01 | Energize the Aircraft Electrical Circuits from the APU |
| TASK 24-41-00-861-002-A-02 | Energize the Aircraft Electrical Circuits from Engine 1(2) |
| TASK 24-41-00-862-002-A | De-energize the Aircraft Electrical Circuits Supplied from the External Power |
| TASK 24-41-00-862-002-A-01 | De-energize the Aircraft Electrical Circuits Supplied from the APU |
| TASK 24-41-00-862-002-A-02 | De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2) |
| TASK 33-24-00-710-001-A | Operational Test of the Lavatory Lighting LQ |
| TASK 33-24-12-000-803-A | Removal of the Accent Ceiling Light |
| TASK 33-24-12-000-805-A | Removal of the Accent Washtable Light |
| TASK 33-24-12-400-803-A | Installation of the Accent Ceiling Light |
| TASK 33-24-12-400-805-A | Installation of the Accent Washtable Light |
Accent Mirror LightSubtask 33-24-12-860-058-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Make sure that the aircraft electrical circuits are energized
(Ref. AMM TASK 24-41-00-861-002).
(2) In the SMART lavatory:
(a) FOR 62LQ*
1 Make sure that the upper service panel (7) is open.
2 Make sure that the service cabinet above the baby nursing table is open.
3 Make sure that the cover of the ceiling light and the cover of the washtable light are removed (Ref. AMM TASK 33-24-12-000-803) (Ref. AMM TASK 33-24-12-000-805).
Subtask 33-24-12-865-065-A ** ON A/C NOT FOR ALL (1) Make sure that the aircraft electrical circuits are energized
(Ref. AMM TASK 24-41-00-861-002).
(2) In the SMART lavatory:
(a) FOR 62LQ*
1 Make sure that the upper service panel (7) is open.
2 Make sure that the service cabinet above the baby nursing table is open.
3 Make sure that the cover of the ceiling light and the cover of the washtable light are removed (Ref. AMM TASK 33-24-12-000-803) (Ref. AMM TASK 33-24-12-000-805).
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
4. Procedure| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H07 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H05 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LAV FWD-OCCUPIED | 1WJ | F01 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LIGHT-LAV | 1LQ | J01 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LAV FWD & MID-OCCUPIED | 1WJ | F01 |
| ** ON A/C NOT FOR ALL | |||
| 2001VU | LAVATORY AFT-OCCUPIED | 11WJ | B04 |
Subtask 33-24-12-420-054-A ** ON A/C NOT FOR ALL
A. Install the Accent Mirror Light
(1) Put the accent mirror light (2) in position and push it until all clamps (4) engage.
(3) Install the brackets (12) with the washers (10) and the screws (9) and install the terminal block (6) on the lavatory wall.
(4) Put the cable (11) in position and install the new TIE WRAP(S) (5).
(5) Install the light cover (3).
Subtask 33-24-12-410-052-A ** ON A/C NOT FOR ALL (1) Put the accent mirror light (2) in position and push it until all clamps (4) engage.
CAUTION:
MAKE SURE THAT THE ELECTRICAL CONNECTORS ARE CLEAN BEFORE YOU DISCONNECT OR CONNECT THEM. CONTAMINATION ON THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO EQUIPMENT.
CAUTION:
REFER TO THE MATCH MARKS MADE DURING THE REMOVAL WHEN YOU CONNECT THE ELECTRICAL WIRES.
INCORRECT CONNECTION OF THE WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
(2) Connect the electrical contacts (1) to the terminal block (6), use the ELEC CONTACTS INSERTION EXTRACTION TOOL M15570-20. (3) Install the brackets (12) with the washers (10) and the screws (9) and install the terminal block (6) on the lavatory wall.
(4) Put the cable (11) in position and install the new TIE WRAP(S) (5).
(5) Install the light cover (3).
B. Close Access
(1) Close Access to the Accent Mirror Light in the SMART lavatory:
(a) FOR 62LQ*
1 Install the cover of the ceiling light and the cover of the washtable light (Ref. AMM TASK 33-24-12-400-803) (Ref. AMM TASK 33-24-12-400-805).
2 Close the upper service panel (7) and tighten the two studs (8).
3 Close the service cabinet above the baby nursing table.
Subtask 33-24-12-865-066-A ** ON A/C NOT FOR ALL (1) Close Access to the Accent Mirror Light in the SMART lavatory:
(a) FOR 62LQ*
1 Install the cover of the ceiling light and the cover of the washtable light (Ref. AMM TASK 33-24-12-400-803) (Ref. AMM TASK 33-24-12-400-805).
2 Close the upper service panel (7) and tighten the two studs (8).
3 Close the service cabinet above the baby nursing table.
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
Subtask 33-24-12-710-054-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H07 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H05 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LAV FWD-OCCUPIED | 1WJ | F01 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LIGHT-LAV | 1LQ | J01 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LAV FWD & MID-OCCUPIED | 1WJ | F01 |
| ** ON A/C NOT FOR ALL | |||
| 2001VU | LAVATORY AFT-OCCUPIED | 11WJ | B04 |
D. Operational Test
(1) Do the operational test of the lavatory lighting (Ref. AMM TASK 33-24-00-710-001).
5. Close-up(1) Do the operational test of the lavatory lighting (Ref. AMM TASK 33-24-00-710-001).
Subtask 33-24-12-860-059-A ** ON A/C NOT FOR ALL
A. Put the aircraft back to its initial configuration.
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2) Make sure that the work area is clean and clear of tools and other items.
(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2) Make sure that the work area is clean and clear of tools and other items.
(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).