Installation of the Captain or F/O Main Instrument-Panel-Light
TASK 33-12-13-400-001-A
Installation of the Captain or F/O Main Instrument-Panel-Light
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 33-12-13-865-051-A
Subtask 33-12-13-560-052-A
Subtask 33-12-13-942-050-A
[Rev.10 from 2021]
2026.04.01 00:52:30 UTC
Installation of the Captain or F/O Main Instrument-Panel-Light
CAUTION:
DO NOT TOUCH THE LAMP GLASS WITH YOUR FINGERS.
THE OILS FROM YOUR SKIN WILL QUICKLY CAUSE DETERIORATION OF THE LAMP.
IF YOU ACCIDENTALLY TOUCH THE LAMP GLASS, CLEAN IT WITH A LINT-FREE CLOTH.
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | CAP - BLANKING |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 211 | COCKPIT |
| 212 | COCKPIT |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 33-12-00-710-001-A | Operational Test of the General Illumination |
Subtask 33-12-13-865-051-A
A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
4. Procedure| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CKPT/DOME | 1LE | H08 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CKPT/DOME | 1LE | H06 |
| ** ON A/C ALL | |||
| 122VU | LIGHTING/FLOOD/CTR INST/PNL | 2LE | Z04 |
Subtask 33-12-13-560-052-A
A. Preparation for Installation
(1) Clean the component interfaces and the adjacent area.
(2) Do an inspection of the component interfaces and the adjacent area.
Subtask 33-12-13-420-050-A (1) Clean the component interfaces and the adjacent area.
(2) Do an inspection of the component interfaces and the adjacent area.
B. Installation of the Captain or F/O Main Instrument-Panel-Light
(1) Remove the CAP - BLANKING and connect the electrical connector (1) to the connector (4) of the light (2).
(2) Install the light (2) in the housing and hold it.
(3) Tighten the four fasteners (3).
Subtask 33-12-13-865-052-A (1) Remove the CAP - BLANKING and connect the electrical connector (1) to the connector (4) of the light (2).
(2) Install the light (2) in the housing and hold it.
(3) Tighten the four fasteners (3).
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
Subtask 33-12-13-710-050-A | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CKPT/DOME | 1LE | H08 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CKPT/DOME | 1LE | H06 |
| ** ON A/C ALL | |||
| 122VU | LIGHTING/FLOOD/CTR INST/PNL | 2LE | Z04 |
D. Do the operational test of Captain or F/O main instrument-panel-light (Ref. AMM TASK 33-12-00-710-001).
5. Close-upSubtask 33-12-13-942-050-A
A. Make sure that the work area is clean and clear of tools and other items.
Main Instrument-Panel Light