Removal of the Pressure Relief Valve
TASK 32-44-15-000-001-A
Removal of the Pressure Relief Valve
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Referenced Information
3. Job Set-up
Subtask 32-44-15-860-050-A ** ON A/C NOT FOR ALL
Subtask 32-44-15-020-050-D ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 00:49:36 UTC
Removal of the Pressure Relief Valve
WARNING:
MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT. UNWANTED ELECTRICAL POWER CAN BE DANGEROUS.
WARNING:
PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
WARNING:
OBEY THE HYDRAULIC SAFETY PROCEDURES.
FIN: 3067GM ** ON A/C NOT FOR ALL
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 2M (6 FT) |
| No specific | 1 | CONTAINER 5 L (1.32 USGAL) |
| No specific | AR | PLUG - BLANKING |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| No specific | AR | WARNING NOTICE(S) |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 20-23-21-911-001-A | Removal/Installation of the Bobbins from their Housings and Installation of O-rings, Square Seals, and Back-up Rings on the Bobbins |
| TASK 29-00-00-910-002-A | Safety Procedures of the Hydraulic System |
| TASK 29-10-00-864-002-A | Depressurize the Yellow Hydraulic System |
| TASK 29-14-00-614-001-A | Depressurization of the Hydraulic Reservoirs |
| TASK 29-23-00-860-001-A | Disconnection of the Isolation Coupling of the Power Transfer Unit (PTU) |
| TASK 32-12-00-010-001-A | Open the Main Gear Doors for Access |
| TASK 32-44-11-200-001-A | Functional Check of Parking/Emergency Brake Accumulator by Reading the Charge Pressure on the Accumulator Gauge |
Subtask 32-44-15-860-050-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Depressurize the Yellow hydraulic system (Ref. AMM TASK 29-10-00-864-002).
(2) Push the pressure release button on the pressure relief valve 3067GM to depressurize the alternate brake system.
(3) Make sure that the pressure on the gauge 2585GM decreases to the fill pressure of the accumulator 2582GM (Ref. AMM TASK 32-44-11-200-001).
Subtask 32-44-15-010-050-A ** ON A/C NOT FOR ALL Subtask 32-44-15-869-051-A ** ON A/C NOT FOR ALL (1) Depressurize the Yellow hydraulic system (Ref. AMM TASK 29-10-00-864-002).
(2) Push the pressure release button on the pressure relief valve 3067GM to depressurize the alternate brake system.
(3) Make sure that the pressure on the gauge 2585GM decreases to the fill pressure of the accumulator 2582GM (Ref. AMM TASK 32-44-11-200-001).
C. Disconnection of the PTU Isolating Coupling
(1) Depressurize the reservoir of the Yellow hydraulic system (Ref. AMM TASK 29-14-00-614-001).
(2) Disconnect the PTU isolation coupling (Ref. AMM TASK 29-23-00-860-001).
(3) Put the ACCESS PLATFORM 2M (6 FT) in position.
(4) Put the CONTAINER 5 L (1.32 USGAL) below the pressure relief valve 3067GM to collect the hydraulic fluid leakage.
Subtask 32-44-15-865-050-A ** ON A/C NOT FOR ALL (1) Depressurize the reservoir of the Yellow hydraulic system (Ref. AMM TASK 29-14-00-614-001).
(2) Disconnect the PTU isolation coupling (Ref. AMM TASK 29-23-00-860-001).
(3) Put the ACCESS PLATFORM 2M (6 FT) in position.
(4) Put the CONTAINER 5 L (1.32 USGAL) below the pressure relief valve 3067GM to collect the hydraulic fluid leakage.
D. Open, safety and tag this(these) circuit breaker(s):
Subtask 32-44-15-941-050-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | L/G/Y BRK/PRESS/IND | 61GG | C10 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | ABCU &/Y BRK/PRESS IND | 61GG | C10 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | HYDRAULIC/HYD POWER/Y | 3803GX | N30 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY | 4GG | M36 |
| 121VU | HYDRAULIC/BRAKING AND STEERING/SYS2/CTL | 3GG | M35 |
| 121VU | HYDRAULIC/BRAKING AND STEERING/SYS1/CTL | 1GG | M34 |
| 121VU | HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY | 2GG | M33 |
| 121VU | HYDRAULIC/PARK BRK/CTL/STBY | 71GG | N37 |
| 121VU | HYDRAULIC/PARK BRK/CTL/NORM | 70GG | N36 |
| 121VU | HYDRAULIC/Y HYD/PUMP ENG2/MONG | 3700GD | Q37 |
| 121VU | HYDRAULIC/Y HYD/PUMP ENG2/CTL | 3701GD | Q36 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | HYDRAULIC/HYD POWER/Y | 3803GX | N31 |
| ** ON A/C NOT FOR ALL | |||
| 123VU | Y HYD/ELEC/PUMP | 3802GX | AB06 |
| 123VU | Y HYD/ELEC/ELEC PUMP/NORM | 3801GX | AB03 |
E. Safety Precautions
(1) Put the WARNING NOTICE(S) in position to tell persons not to pressurize the Yellow hydraulic system:
4. Procedure(1) Put the WARNING NOTICE(S) in position to tell persons not to pressurize the Yellow hydraulic system:
- On panel 40VU in the cockpit,
- On the ground service panel of the Yellow hydraulic system.
Subtask 32-44-15-020-050-D ** ON A/C NOT FOR ALL
A. Removal of the Pressure Relief Valve 3067GM
(1) Obey the hydraulic safety procedures (Ref. AMM TASK 29-00-00-910-002).
(2) Remove the bolts (8), the washers (9) and the bonding strap (10).
(3) Remove the pressure relief valve (7) from the manifold (1).
(4) Remove and discard the packings (2) and the back-up rings (3) from the bobbins (4).
(5) If necessary, remove the bobbins (4) from the pressure relief valve (7) (Ref. AMM TASK 20-23-21-911-001). Remove and discard the square seals (6) and the back-up rings (5) from the bobbins (4).
(6) Put the PLUG-BLANKING in each disconnected line end.
(1) Obey the hydraulic safety procedures (Ref. AMM TASK 29-00-00-910-002).
(2) Remove the bolts (8), the washers (9) and the bonding strap (10).
(3) Remove the pressure relief valve (7) from the manifold (1).
(4) Remove and discard the packings (2) and the back-up rings (3) from the bobbins (4).
(5) If necessary, remove the bobbins (4) from the pressure relief valve (7) (Ref. AMM TASK 20-23-21-911-001). Remove and discard the square seals (6) and the back-up rings (5) from the bobbins (4).
(6) Put the PLUG-BLANKING in each disconnected line end.
Pressure Release Knob of the Alternate Brake System