Functional Check of MLG Torque Link Damper Fluid Level

TASK 32-11-11-200-001-A
Functional Check of MLG Torque Link Damper Fluid Level

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 731
ZONE: 741

1. Reason for the Job
Refer to the MPD TASK: 321111-03
FUNCTIONAL CHECK OF MLG TORQUE LINK DAMPER FLUID LEVEL
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	SAFETY BARRIER(S)
No specific	AR	WARNING NOTICE(S)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
731	L.H MAIN GEAR
741	R.H MAIN GEAR

D. Referenced Information

REFERENCE	DESIGNATION
TASK 32-00-00-481-001-A	Installation of the Safety Devices on the Landing Gears
TASK 12-12-32-611-006-A	Replenishment of the MLG Torque Link Damper (for corrective action)
Torque Link Damper ** ON A/C NOT FOR ALL
Torque Link Damper ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 32-11-11-941-054-A

A. Safety Precautions
(1) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
(2) Make sure that the safety devices are installed on each MLG (Ref. AMM TASK 32-00-00-481-001).
(3) On panel 400VU:

Make sure that the landing-gear control lever is in the DOWN position
Put the WARNING NOTICE(S) in position to tell persons not to operate the landing gears.

Subtask 32-11-11-110-051-A

B. Cleaning
(1) If necessary, clean the level indicator lines of the torque link damper with a clean Textile-Lint free Cotton - (Material No.14SBA1) made moist with Non Aqueous Cleaner-General - - (Material No.08BAA9) .

4. Procedure
Subtask 32-11-11-210-057-A

A. Functional Check of the MLG Torque-Link Damper Fluid-Level
(1) Make sure that the level indicator shows the hydraulic fluid level above the REFILL range (above the satisfactory level).
(a) If the level indicator shows the hydraulic fluid level in the REFILL range (at or below the satisfactory level), do the steps that follow:
1 Make sure that the safety devices are installed on each MLG (Ref. AMM TASK 32-00-00-481-001).
2 Do the replenishment of the MLG torque-link damper (Ref. AMM TASK 12-12-32-611-006).

5. Close-up
Subtask 32-11-11-942-069-A

A. Removal of Equipment
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the WARNING NOTICE(S).
(3) Remove the SAFETY BARRIERS.
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.04.01 00:40:00 UTC