Replacement of the Cassette with the QAR not Energized

TASK 31-33-52-600-006-A
Replacement of the Cassette with the QAR not Energized

ZONE: 127
FIN: 3TU ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
127	REAR AVIONIC COMPARTMENT
824

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
QAR Cassette

3. Job Set-up

NOTE: If the sticker of the cassette is in incorrect position, the QAR does not operate. Thus we recommend the replacement of the cassette with the QAR energized.

Subtask 31-33-52-865-059-A ** ON A/C NOT FOR ALL

A. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	RCDR/ACCLRM	9TU	K18

Subtask 31-33-52-010-057-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position at the access door 824.
(2) Open the access door 824.

4. Procedure
Subtask 31-33-52-020-056-A ** ON A/C NOT FOR ALL

A. Removal of the Cassette
(1) Loosen the two wing nuts (5) and open the door (4) of the QAR.
(2) Lift and pull the cassette extraction/locking lever (3) to eject the cassette (2).
(3) Remove the cassette (2).
(4) Lower the extraction/locking lever (3).
(5) Close the door (4) and lock it with the two wing nuts (5).

Subtask 31-33-52-420-056-A ** ON A/C NOT FOR ALL

B. Installation of the Cassette
(1) Loosen the two wing nuts (5) and open the door (4) of the QAR.
(2) Lift the cassette extraction/locking lever (3).
(3) Make sure that the BOT (Beginning Of Tape) warning sticker is in front of the reflector of the cassette.
(4) Install the cassette (2) with the shutter protection on the extraction/locking lever side.
(5) Push the cassette (2) fully in until it engages correctly in its chamber.
(6) Lower the extraction/locking lever (3).
(7) Close the door (4) and lock it with the two wing nuts (5).

NOTE: At the energization of the QAR, the BOT sensing device automatically sets the track 1.

Subtask 31-33-52-861-055-A ** ON A/C NOT FOR ALL

C. Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).

Subtask 31-33-52-865-060-A ** ON A/C NOT FOR ALL

D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	RCDR/ACCLRM	9TU	K18

Subtask 31-33-52-210-052-A ** ON A/C NOT FOR ALL

E. Make sure that the FIRST TRACK light (2) on the QAR is on.

NOTE: If the FIRST TRACK light (2) is not on, do the procedure with the QAR energized.

5. Close-up
Subtask 31-33-52-410-058-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the access door 824.
(3) Remove the access platform(s).

Subtask 31-33-52-862-055-A ** ON A/C NOT FOR ALL

B. De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

[Rev.9 from 2019] 2026.04.01 00:35:00 UTC