W DOC AIRBUS | AMM A320F

Installation of the Ice Detector

TASK 30-81-31-400-001-A
Installation of the Ice Detector

WARNING: MAKE SURE THAT THE CIRCUIT BREAKERS RELATED TO THE WEATHER RADAR ARE OPENED, SAFETIED AND TAGGED.
WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
FIN: 2DD1 ** ON A/C NOT FOR ALL
FIN: 2DD2 ** ON A/C NOT FOR ALL
1. Reason for the Job
Self explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
ACCESS PLATFORM 2M (6 FT)
No specific
Torque wrench: range to between 0.44 and 0.36 m.daN (38.94 and 31.86 lbf.in ) T
 B. Consumable Materials
REFERENCE
DESIGNATION
(Material No.06AAB1)
Polysulfide Sealant-General Purpose Fillet -
 C. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
811
 D. Expendable Parts
FIG.ITEM
DESIGNATION
IPC-CSN
2
SEAL
AIPC 30-81-01-01-020
2
JOINT
AIPC 30-81-81-01-020
 E. Referenced Information
REFERENCE
DESIGNATION
TASK 20-28-00-912-802-A
Electrical Bonding - General Maintenance Procedure
TASK 24-41-00-861-002-A
Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01
Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02
Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A
De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01
De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02
De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 30-81-00-710-001-A
Operational Test of the Ice Detection System
TASK 52-41-00-010-002-A
Open the Avionics Compartment Doors for Access
TASK 52-41-00-410-002-A
Close the Avionics Compartment Doors after Access
F Ice Detector ** ON A/C NOT FOR ALL
3. Job Set-up
Subtask 30-81-31-860-050-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
   (1) Make sure that the aircraft electrical circuits are energized (Ref. AMM TASK 24-41-00-861-002).
Subtask 30-81-31-010-051-A ** ON A/C NOT FOR ALL
B. Get access to the avionics compartment.
   (1) Make sure that an ACCESS PLATFORM 2M (6 FT) is in position at access door 811.
   (2) Make sure that access door 811 is open (Ref. AMM TASK 52-41-00-010-002).
Subtask 30-81-31-865-051-A ** ON A/C NOT FOR ALL
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
121VUCOM NAV/RADAR/15SQ1K13
** ON A/C NOT FOR ALL
FOR FIN: 2DD1 (DETICE, L)
122VUANTI ICE/ICE DET/L4DD1V12
FOR FIN: 2DD2 (DETICE, R)
122VUANTI ICE/ICE DET/R4DD2V13
4. Procedure
Subtask 30-81-31-420-050-A ** ON A/C NOT FOR ALL
A. Installation of the Ice Detector
F Ice Detector ** ON A/C NOT FOR ALL
   (1) Clean the component interfaces and the adjacent area.
   (2) Do an inspection of the component interfaces and the adjacent area.
   (3) Remove the CAP-BLANKING from each electrical connector and receptacle.
   (4) Put a new AIPC 30-81-01-01-020 SEAL (2) in position on the ice detector (4).
   (5) Put the ice detector (4) with the joint (2) in position on the structure (1).
   (6) Install the screws (5).
   (7) TORQUE the screws (5) to between 0.44 and 0.36 m.daN (38.94 and 31.86 lbf.in ) T.
   (8) Make a sealing bead with Polysulfide Sealant-General Purpose Fillet - (Material No.06AAB1) around the ice detector (4).
   (9) Complete the bonding procedure (Ref. AMM TASK 20-28-00-912-802):
     (a) FOR [2DD1] (DET-ICE, L)
The aft bolt and washer at the left side
     (b) FOR [2DD2] (DET-ICE, R)
The aft bolt and washer at the right side.
CAUTION: MAKE SURE THAT THE ELECTRICAL CONNECTORS ARE CLEAN BEFORE YOU DISCONNECT OR CONNECT THEM. CONTAMINATION ON THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO EQUIPMENT.
   (10) Connect the electrical connector (3).
Subtask 30-81-31-420-050-B ** ON A/C NOT FOR ALL
A. Installation of the Ice Detector
F Ice Detector ** ON A/C NOT FOR ALL
   (1) Clean the component interfaces and the adjacent area.
   (2) Do an inspection of the component interfaces and the adjacent area.
   (3) Remove the CAP-BLANKING from each electrical connector and receptacle.
   (4) Put a new AIPC 30-81-81-01-020 JOINT (2) in position on the ice detector (4).
   (5) Put the ice detector (4) with the joint (2) in position on the structure (1).
   (6) Install the screws (5).
   (7) TORQUE the screws (5) to between 0.44 and 0.36 m.daN (38.94 and 31.86 lbf.in ) T.
   (8) Make a sealing bead with Polysulfide Sealant-General Purpose Fillet - (Material No.06AAB1) around the ice detector (4).
   (9) Complete the bonding procedure (Ref. AMM TASK 20-28-00-912-802):
     (a) FOR [2DD1] (DET-ICE, L)
The aft bolt and washer at the left side
     (b) FOR [2DD2] (DET-ICE, R)
The aft bolt and washer at the right side.
CAUTION: MAKE SURE THAT THE ELECTRICAL CONNECTORS ARE CLEAN BEFORE YOU DISCONNECT OR CONNECT THEM. CONTAMINATION ON THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO EQUIPMENT.
   (10) Connect the electrical connector (3).
Subtask 30-81-31-865-052-A ** ON A/C NOT FOR ALL
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
121VUCOM NAV/RADAR/15SQ1K13
** ON A/C NOT FOR ALL
FOR FIN: 2DD1 (DETICE, L)
122VUANTI ICE/ICE DET/L4DD1V12
FOR FIN: 2DD2 (DETICE, R)
122VUANTI ICE/ICE DET/R4DD2V13
Subtask 30-81-31-710-050-A ** ON A/C NOT FOR ALL
C. Do an operational test of the ice detection system (Ref. AMM TASK 30-81-00-710-001).
5. Close-up
Subtask 30-81-31-410-050-A ** ON A/C NOT FOR ALL
A. Close Access
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Close access door 811 (Ref. AMM TASK 52-41-00-410-002).
   (3) Remove the access platform(s).
Subtask 30-81-31-862-051-A ** ON A/C NOT FOR ALL
B. De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).
[Rev.10 from 2021] 2026.04.01 00:33:10 UTC
"Aviabrain" 2025