Removal of the Inner Line Heater
TASK 30-73-54-000-001-A
Removal of the Inner Line Heater
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 30-73-54-680-050-A ** ON A/C NOT FOR ALL
Subtask 30-73-54-020-050-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 00:32:54 UTC
Removal of the Inner Line Heater
FIN: 25DW ** ON A/C NOT FOR ALL
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | ACCESS PLATFORM 2M (6 FT) |
| No specific | AR | ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE |
| No specific | AR | CAP - BLANKING |
| No specific | 1 | CUTTER - THIN BLADE |
| No specific | 1 | PLIERS - END-CUTTING |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 131GW, 812, 825 |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 12-24-38-680-001-A | Draining of the Potable Water System (with Electrical Power) |
| TASK 12-24-38-680-002-A | Draining of the Potable Water System (without Electrical Power) |
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 52-30-00-860-001-A | Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
Subtask 30-73-54-680-050-A ** ON A/C NOT FOR ALL
A. Drain the potable water system (Ref. AMM TASK 12-24-38-680-001) or (Ref. AMM TASK 12-24-38-680-002).
Subtask 30-73-54-861-050-A ** ON A/C NOT FOR ALL Subtask 30-73-54-865-050-A ** ON A/C NOT FOR ALL C. Open, safety and tag this(these) circuit breaker(s):
Subtask 30-73-54-010-050-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 2000VU | POT/WASTE WIP-HEATER-LINE | 21DW | A03 |
| 2000VU | POT/WASTE WIP-HEATER-LINE | 1DW | A02 |
| 2000VU | POT/WASTE WIP-HEATER-CTL | 2DW | A01 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | POT WIP-HEATER-LINE | 21DW | A03 |
| 2000VU | POT WIP-HEATER-LINE | 1DW | A02 |
| 2000VU | POT WIP-HEATER-CTL | 2DW | A01 |
D. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position at the access door 812 of the avionics compartment.
(2) Open the access door 812.
(3) Put the ACCESS PLATFORM 2M (6 FT) in position at the FWD cargo-compartment door 825.
(4) Open the FWD cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-001).
(5) Set the CARGO COMPT LIGHT switch 6LU to the ON position.
(6) In the forward cargo compartment, remove the sidewall panel 131GW.
4. Procedure(1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position at the access door 812 of the avionics compartment.
(2) Open the access door 812.
(3) Put the ACCESS PLATFORM 2M (6 FT) in position at the FWD cargo-compartment door 825.
(4) Open the FWD cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-001).
(5) Set the CARGO COMPT LIGHT switch 6LU to the ON position.
(6) In the forward cargo compartment, remove the sidewall panel 131GW.
Subtask 30-73-54-020-050-A ** ON A/C NOT FOR ALL
A. Removal of the Inner Line Heater
(1) Disconnect the electrical connector (1).
(2) Put CAP - BLANKING on the electrical connector and the electrical receptacle.
(3) Remove the adhesive tape (4) that holds the sleeve (5).
(4) Remove the sleeve (5).
(5) Loosen the nut (3).
(6) Remove the clamps (7).
(7) Remove the box (8).
(8) Disconnect the tee (10) from the pipes (9), (11) and (12).
(9) Remove the inner line heater (2) from the pipe (11) and from the tee (10).
(10) Remove the tee (10).
(11) Remove the inner line heater (2) from the pipe (6).
Subtask 30-73-54-020-050-B ** ON A/C NOT FOR ALL (1) Disconnect the electrical connector (1).
(2) Put CAP - BLANKING on the electrical connector and the electrical receptacle.
(3) Remove the adhesive tape (4) that holds the sleeve (5).
(4) Remove the sleeve (5).
(5) Loosen the nut (3).
(6) Remove the clamps (7).
(7) Remove the box (8).
(8) Disconnect the tee (10) from the pipes (9), (11) and (12).
(9) Remove the inner line heater (2) from the pipe (11) and from the tee (10).
(10) Remove the tee (10).
(11) Remove the inner line heater (2) from the pipe (6).
A. Removal of the Inner Line Heater
(1) Disconnect the electrical connector (1).
(2) Put CAP - BLANKING on the electrical connector and the electrical receptacle.
(3) Remove the adhesive tape (4) that holds the sleeve (5).
(4) Remove the sleeve (5).
(5) Loosen the nut (3).
(6) Remove the clamps (11).
(7) Remove the half box (12) with a CUTTER - THIN BLADE and a PLIERS - END-CUTTING.
(8) Discard the half box (12).
(9) Disconnect the tee (8) from the pipes (7), (9) and (10).
(10) Remove the inner line heater (2) from the pipe (9) and from the tee (8).
(11) Remove the tee (8).
(12) Remove the inner line heater (2) from the pipe (6).
(1) Disconnect the electrical connector (1).
(2) Put CAP - BLANKING on the electrical connector and the electrical receptacle.
(3) Remove the adhesive tape (4) that holds the sleeve (5).
(4) Remove the sleeve (5).
(5) Loosen the nut (3).
(6) Remove the clamps (11).
(7) Remove the half box (12) with a CUTTER - THIN BLADE and a PLIERS - END-CUTTING.
(8) Discard the half box (12).
(9) Disconnect the tee (8) from the pipes (7), (9) and (10).
(10) Remove the inner line heater (2) from the pipe (9) and from the tee (8).
(11) Remove the tee (8).
(12) Remove the inner line heater (2) from the pipe (6).
Heater-Inner Line