DOC AIRBUS | AMM A320FRemoval of Sensor
TASK 30-71-19-000-001-A
Removal of Sensor
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 30-71-19-861-050-A ** ON A/C NOT FOR ALL Subtask 30-71-19-865-053-A ** ON A/C NOT FOR ALL
Subtask 30-71-19-020-050-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 00:31:54 UTC
Removal of Sensor
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ELEC CONTACTS INSERTION EXTRACTION TOOL M15570-20 |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 150 | AFT CARGO COMPARTMENT FWD PRESS BULKHEAD TO AFT BULKHEAD OF AFT CARGO COMPARTMENT |
| 170 | AFT CAB U/FLOOR COMPT AFT BHD OF BULK |
| 162DW |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 25-55-12-000-001-A | Removal of the Aft Cargo-Compartment Partition at FR65 |
| TASK 52-30-00-860-006-A | Open the Bulk Cargo-Compartment Door |
Temperature Sensor - Removal/InstallationSubtask 30-71-19-861-050-A ** ON A/C NOT FOR ALL Subtask 30-71-19-865-053-A ** ON A/C NOT FOR ALL
B. Open, safety and tag this(these) circuit breaker(s):
Subtask 30-71-19-010-050-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 2001VU | POT/WASTE WIP-HEATER-CTL | 32DW | D02 |
| 2001VU | WASTE WIP-HEATER-LINE | 31DU | E04 |
C. Get Access
(1) Open the bulk cargo-compartment door (Ref. AMM TASK 52-30-00-860-006).
(2) Set cargo-compartment light switch 18LU to on.
(3) Remove rear-wall partition-panel 162DW (Ref. AMM TASK 25-55-12-000-001).
4. Procedure(1) Open the bulk cargo-compartment door (Ref. AMM TASK 52-30-00-860-006).
(2) Set cargo-compartment light switch 18LU to on.
(3) Remove rear-wall partition-panel 162DW (Ref. AMM TASK 25-55-12-000-001).
Subtask 30-71-19-020-050-A ** ON A/C NOT FOR ALL
A. Removal of the Temperature Sensor
(1) Remove and discard the TIE WRAP(S) which attach the electrical wires of the sensor assemblies (3) and (4).
(2) Remove the insulation blanket (6) from the sensor assemblies (3) and (4).
(3) Identify all the electrical wires before you disconnect them.
(4) Disconnect the electrical connections:
(5) Remove the screws (1) and remove the sensor assemblies (3) and (4) from the tank connecting tube (5).
(1) Remove and discard the TIE WRAP(S) which attach the electrical wires of the sensor assemblies (3) and (4).
(2) Remove the insulation blanket (6) from the sensor assemblies (3) and (4).
(3) Identify all the electrical wires before you disconnect them.
(4) Disconnect the electrical connections:
CAUTION:
MAKE MATCH MARKS ON ALL THE ELECTRICAL WIRES BEFORE YOU DISCONNECT THEM. INCORRECT CONNECTION OF WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
CAUTION:
MAKE SURE THAT THE ELECTRICAL CONNECTORS ARE CLEAN BEFORE YOU DISCONNECT OR CONNECT THEM. CONTAMINATION ON THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO EQUIPMENT.
(a) Disconnect the electrical connections (2) with the ELEC CONTACTS INSERTION EXTRACTION TOOL M15570-20. (5) Remove the screws (1) and remove the sensor assemblies (3) and (4) from the tank connecting tube (5).