DOC AIRBUS | AMM A320FRemoval of the Temperature Sensor
TASK 30-71-18-000-001-A
Removal of the Temperature Sensor
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 30-71-18-861-050-A ** ON A/C NOT FOR ALL Subtask 30-71-18-865-053-A ** ON A/C NOT FOR ALL
Subtask 30-71-18-020-050-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 00:31:52 UTC
Removal of the Temperature Sensor
WARNING:
DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:
1. Reason for the Job- FLUSH IT AWAY WITH CLEAN WATER
- GET MEDICAL AID.
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE |
| No specific | 1 | ELEC CONTACTS INSERTION EXTRACTION TOOL M15570-20 |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 150 | AFT CARGO COMPARTMENT FWD PRESS BULKHEAD TO AFT BULKHEAD OF AFT CARGO COMPARTMENT |
| 160 | BULK CARGO COMPARTMENT AFT BULKHEAD OF AFT CARGO COMPARTMENT TO AFT BULKHEAD OF BULK CARGO COMPARTMENT |
| 162DW |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 25-55-12-000-001-A | Removal of the Aft Cargo-Compartment Partition at FR65 |
| TASK 52-30-00-860-006-A | Open the Bulk Cargo-Compartment Door |
Temperature SensorSubtask 30-71-18-861-050-A ** ON A/C NOT FOR ALL Subtask 30-71-18-865-053-A ** ON A/C NOT FOR ALL
B. Open, safety and tag this(these) circuit breaker(s):
Subtask 30-71-18-010-050-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 2001VU | POT/WASTE WIP-HEATER-CTL | 32DW | D02 |
| 2001VU | WASTE WIP-HEATER-LINE | 31DU | E04 |
C. Get Access
(1) Open the bulk cargo-compartment door (Ref. AMM TASK 52-30-00-860-006).
(2) Put an ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position at the bulk cargo-compartment door.
(3) Set cargo-compartment light switch 18LU to on.
(4) Remove rear-wall partition panel 162DW (Ref. AMM TASK 25-55-12-000-001).
4. Procedure(1) Open the bulk cargo-compartment door (Ref. AMM TASK 52-30-00-860-006).
(2) Put an ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position at the bulk cargo-compartment door.
(3) Set cargo-compartment light switch 18LU to on.
(4) Remove rear-wall partition panel 162DW (Ref. AMM TASK 25-55-12-000-001).
Subtask 30-71-18-020-050-A ** ON A/C NOT FOR ALL
A. Removal of the Temperature Sensor
(1) Remove and discard the tie-wraps which attach the electrical wires of the clamp sensor assembly (4).
(2) Remove the insulation blanket (2) from the clamp sensor assembly (4).
(3) Identify all the electrical wires before you disconnect them.
(5) Loosen the spring clamp (5) and remove the clamp sensor assembly (4) from the tank connection tube (1).
(1) Remove and discard the tie-wraps which attach the electrical wires of the clamp sensor assembly (4).
(2) Remove the insulation blanket (2) from the clamp sensor assembly (4).
(3) Identify all the electrical wires before you disconnect them.
CAUTION:
MAKE SURE THAT THE ELECTRICAL CONNECTORS ARE CLEAN BEFORE YOU DISCONNECT OR CONNECT THEM. CONTAMINATION ON THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO EQUIPMENT.
(4) Disconnect the electrical connections (3) with a ELEC CONTACTS INSERTION EXTRACTION TOOL M15570-20. (5) Loosen the spring clamp (5) and remove the clamp sensor assembly (4) from the tank connection tube (1).