Reactivation of the Engine Anti-Ice Valve from the OPEN Position

TASK 30-21-00-440-002-A
Reactivation of the Engine Anti-Ice Valve from the OPEN Position

1. Reason for the Job
MMEL 30-21-01B
ENGINE ANTI-ICE VALVE
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-42-00-861-001-A	Energize the Ground Service Network from the External Power
TASK 24-42-00-862-001-A	De-energize the Ground Service Network Supplied from the External Power
TASK 30-21-51-000-041-A	Removal of the Engine Air-Intake Anti-ice Valve
TASK 30-21-51-400-042-A	Installation of the Engine Air-Intake Anti-ice Valve
TASK 71-13-00-010-040-A	Opening of the Fan Cowl Doors
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors
TASK 71-13-00-410-040-A	Closing of the Fan Cowl Doors
TASK 71-13-00-410-040-B	Closing of the Fan Cowl Doors
Anti-Ice Valve of the Engine Air Intake

3. Job Set-up
Subtask 30-21-00-861-061-A ** ON A/C NOT FOR ALL

A. Energize the ground service network
(Ref. AMM TASK 24-42-00-861-001).

Subtask 30-21-00-860-055-A ** ON A/C NOT FOR ALL

B. Safety Precautions
(1) On the center pedestal, on ENG panel 115VU:
(a) Make sure that the ENG/MODE selector switch is in the NORM position.
(b) Make sure that the ENG/MASTER 1(2) control switch was in the OFF position not less than five minutes before you do this procedure.
(c) Make sure that the WARNING NOTICE(S) are in position to tell persons not to operate:

The ENG/MODE selector switch, and
The ENG/MASTER 1(2) control switch.

(2) On the ENG section of maintenance panel 50VU:
(a) Make sure that the ON legend of the FADEC GND PWR/1(2) pushbutton switch is off.
(b) Make sure that the WARNING NOTICE(S) is in position to tell persons not to energize FADEC 1(2).
(3) On the ANTI ICE section of the panel 25VU:
(a) Release the ANTI ICE/ENG 1(2) pushbutton switch (the ON legend goes off).

Subtask 30-21-00-865-054-A ** ON A/C NOT FOR ALL

C. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
FOR FIN: 1000EM1 (ENGINE1)
122VU	ANTI ICE/ENG/1	1DN1	X10
FOR FIN: 1000EM2 (ENGINE2)
122VU	ANTI ICE/ENG/2	1DN2	W10

Subtask 30-21-00-010-055-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL, 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL, 448AR

4. Procedure
Subtask 30-21-00-440-051-A ** ON A/C NOT FOR ALL

A. Reactivation of the Anti-Ice Valve
(1) Removal of the lockwire:

WARNING: USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

(a) Cut and remove the lockwire from the locking pin.
(2) On the anti-ice valve, remove the pin that locks the manual override control.
(3) Install the locking pin in the transportation hole which is in the valve.

Subtask 30-21-00-440-051-D ** ON A/C NOT FOR ALL

A. Reactivation of the Anti-Ice Valve

CAUTION: IF THE ANTI-ICE VALVE IS LOCKED IN THE OPEN POSITION, AND THERE WILL BE A TAKE-OFF WITH AN OAT MORE THAN ISA FOR MORE THAN TWO MINUTES, YOU MUST REPLACE THE ANTI-ICE VALVE. IF YOU DO NOT REPLACE THE ANTI-ICE VALVE, YOU CAN CAUSE DAMAGE TO THE VALVE AND ADJACENT AREA.

(1) Replace the anti-ice valve (Ref. AMM TASK 30-21-51-000-041) and (Ref. AMM TASK 30-21-51-400-042) in the following conditions:
(a) If there is one take-off for more than two minutes with an OAT more than ISA during the time of deactivation of the anti-ice valve.
(b) If you have no information about take-off and OAT conditions.
(2) Removal of the lockwire:

(a) Cut and remove the lockwire from the locking pin.
(3) On the anti-ice valve, remove the pin that locks the manual override control.
(4) Install the locking pin in the transportation hole which is in the valve.

5. Close-up
Subtask 30-21-00-865-061-A ** ON A/C NOT FOR ALL

A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
FOR FIN: 1000EM1 (ENGINE1)
122VU	ANTI ICE/ENG/1	1DN1	X10
FOR FIN: 1000EM2 (ENGINE2)
122VU	ANTI ICE/ENG/2	1DN2	W10

Subtask 30-21-00-410-055-A ** ON A/C NOT FOR ALL

B. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL, 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL, 448AR
(3) Remove the WARNING NOTICE(S).

Subtask 30-21-00-862-061-A ** ON A/C NOT FOR ALL

C. De-energize the ground service network
(Ref. AMM TASK 24-42-00-862-001).

[Rev.10 from 2021] 2026.04.01 00:28:40 UTC