Removal of the Reservoir Depressurization Valve of the Yellow Hydraulic System

TASK 29-14-16-000-003-A
Removal of the Reservoir Depressurization Valve of the Yellow Hydraulic System

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

FIN: 3087GM

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	CAP - BLANKING
No specific	1	PLUG - BLANKING
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	2	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
198CB, 198DB

C. Referenced Information

REFERENCE	DESIGNATION
TASK 29-00-00-864-001-A	Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action
TASK 29-00-00-910-002-A	Safety Procedures of the Hydraulic System
TASK 29-14-00-614-001-A	Depressurization of the Hydraulic Reservoirs
Depressurization Valve

3. Job Set-up
Subtask 29-14-16-865-053-A

A. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	HYDRAULIC/HYD POWER/Y	3803GX	N30
** ON A/C NOT FOR ALL
121VU	HYDRAULIC/HYD POWER/Y	3803GX	N31
** ON A/C ALL
123VU	Y HYD/ELEC/PUMP	3802GX	AB06
123VU	Y HYD/ELEC/ELEC PUMP/NORM	3801GX	AB03

Subtask 29-14-16-860-052-A

B. Aircraft Maintenance Configuration

WARNING: OBEY THE HYDRAULIC SAFETY PROCEDURES.

(1) Obey the hydraulic safety procedures (Ref. AMM TASK 29-00-00-910-002).
(2) Put the WARNING NOTICE(S) in position to tell persons not to pressurize the Yellow hydraulic system:

In the cockpit on the hydraulic panel 40VU of the overhead panel,
On the ground service panel of the Yellow hydraulic system.

(3) Make sure that the Yellow hydraulic system is depressurized and put it in the maintenance configuration.
(Ref. AMM TASK 29-00-00-864-001).
(4) Depressurize the reservoir of the Yellow hydraulic system (Ref. AMM TASK 29-14-00-614-001).

Subtask 29-14-16-010-052-A

C. Get Access
(1) Open the access panel 198CB.
(2) Remove the access panel 198DB.

4. Procedure
Subtask 29-14-16-020-052-A

A. Removal of the Reservoir Depressurization Valve

CAUTION: USE A SECOND WRENCH TO APPLY COUNTERTORQUE TO THE UNION WHEN YOU DISCONNECT/CONNECT HYDRAULIC LINES ON UNIONS. IF YOU DO NOT USE THE SECOND WRENCH, THERE IS A RISK THAT YOU WILL LOOSEN OR TIGHTEN THE UNION TOO MUCH.

(1) Hold the reducer (2) and disconnect the line end-fitting (1) from the reducer (2).
(2) Install the CAP - BLANKING on the disconnected line ends.

WARNING: USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

(3) Cut and remove the lockwire which safeties the cap assembly.
(4) Remove the parts which are attached to the removed depressurization valve as follows:
(a) Hold the depressurization valve (4) and remove the reducer (2).
(b) Remove and discard the O-ring (3).
(c) Put a PLUG - BLANKING on the reducer (2) and the depressurization valve (4).
(5) Remove the nuts (6) and the bolts (5).
(6) Remove the depressurization valve (4) from the ground service panel.

[Rev.10 from 2021] 2026.04.01 00:24:37 UTC