Removal of the Engine-Pump Heat-Shield Assembly

TASK 29-13-51-000-807-A
Removal of the Engine-Pump Heat-Shield Assembly

WARNING: WEAR APPLICABLE PERSONAL PROTECTIVE EQUIPMENT (PPE) WHEN YOU DO THIS TASK. BEFORE YOU USE PPE, READ, UNDERSTAND AND OBEY ALL INSTRUCTIONS FOR ITS USE. THESE INSTRUCTIONS INCLUDE INSTRUCTIONS FROM THE MANUFACTURER, YOUR EMPLOYER AND GOVERNMENT REGULATIONS. YOU CAN GET INJURED IF YOU DO NOT USE PPE. GET INSTRUCTIONS FROM YOUR EMPLOYER ON WHICH PPE IS NECESSARY.

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AND THE ADJACENT COMPONENTS AFTER ENGINE SHUTDOWN. THE ENGINE, THE ENGINE OIL AND THE ADJACENT COMPONENTS CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

ZONE: 445

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	COVER - PROTECTION
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
445	FAN AND ACCESSORY GEARBOX
195BB, 198CB
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 29-10-00-864-002-A	Depressurize the Yellow Hydraulic System
TASK 29-13-51-000-806-A	Removal of the Yellow Engine Driven Pump
TASK 29-14-00-614-001-A	Depressurization of the Hydraulic Reservoirs
TASK 71-00-00-860-833-A	Procedure to Prevent Engine Motoring
TASK 71-13-00-010-802-A	Opening of the Fan Cowl Doors
TASK 78-30-00-040-805-A	Deactivation of the Thrust Reverser System for Ground Maintenance
TASK 78-36-00-010-802-A	Opening of the Thrust Reverser Cowl-Doors
Engine-Pump Heat-Shield Assembly

3. Job Set-up
Subtask 29-13-51-860-081-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Make sure that the Yellow hydraulic system is depressurized.
(Ref. AMM TASK 29-10-00-864-002)
(2) Depressurize the reservoir of the Yellow hydraulic system.
(Ref. AMM TASK 29-14-00-614-001)

Subtask 29-13-51-941-070-A ** ON A/C NOT FOR ALL

B. Safety Precautions
(1) On AIR COND panel 30VU:

Make sure that the APU BLEED pushbutton switch is released (the ON legend is off).
Put a WARNING NOTICE(S) in position to tell persons not to operate this pushbutton switch.

(2) Open access door 198CB.
(a) Put WARNING NOTICE(S) in position to tell persons not to pressurize the Yellow hydraulic system on the ground service panel.
(3) On the HYD section of panel 40VU:

Put WARNING NOTICE(S) in position to tell persons not to pressurize the Yellow hydraulic system.

(4) Put a WARNING NOTICE(S) in position on access door 195BB to tell persons not to pressurize the reservoir of the Yellow hydraulic system.
(5) Do the procedure to prevent engine motoring
(Ref. AMM TASK 71-00-00-860-833).

Subtask 29-13-51-010-062-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL 448AR

Subtask 29-13-51-040-051-A ** ON A/C NOT FOR ALL

D. Deactivation of the Thrust Reverser for Maintenance

WARNING: YOU MUST DEACTIVATE THE THRUST REVERSER BEFORE YOU DO WORK ON OR AROUND IT. IF YOU DO NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE AN INJURY AND/OR DAMAGE.

(1) Do the deactivation of the thrust reverser system for maintenance (Ref. AMM TASK 78-30-00-040-805).

Subtask 29-13-51-010-063-A ** ON A/C NOT FOR ALL

E. Get Access
(1) Open the right thrust-reverser cowl-door (Ref. AMM TASK 78-36-00-010-802):
(a) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
462AR

Subtask 29-13-51-020-061-A ** ON A/C NOT FOR ALL

F. Remove the Engine Driven Hydraulic-Pump (EDP) (Ref. AMM TASK 29-13-51-000-806).

4. Procedure
Subtask 29-13-51-020-060-A ** ON A/C NOT FOR ALL

A. Removal of the Engine Driven Hydraulic-Pump (EDP) Heat Shield Assembly
(1) Remove the hydraulic EDP heat shield (1).
(a) Remove the four bolts (3) and the four washers (2) that attach the forward bracket (4) and the aft bracket (5) to the accessory gearbox.
(b) Remove the forward bracket (4), the aft bracket (5) and the hydraulic EDP heat shield (1) from the engine.
(c) Remove the two bolts (7) and the two washers (6) that attach the forward bracket (4) to the hydraulic EDP heat shield (1).
(d) Remove the forward bracket (4) from the hydraulic EDP heat shield (1).
(e) Remove the two bolts (7) and two washers (6) that attach the aft bracket (5) to the hydraulic EDP heat shield (1).
(f) Remove the aft bracket (5) from the hydraulic EDP heat shield (1).
(2) Installation of the protection covers

CAUTION: INSTALL PROTECTION COVERS ON ALL THE OPENINGS IMMEDIATELY TO PREVENT DAMAGE TO THE ENGINE.

(a) Make sure that you install COVER - PROTECTION as necessary to prevent damage to the engine.

[Rev.10 from 2021] 2026.04.01 00:23:41 UTC