Removal of the Magnetic Level-Indicator Assembly

TASK 28-43-22-000-002-A
Removal of the Magnetic Level-Indicator Assembly

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

FIN: 64QM ** ON A/C NOT FOR ALL
FIN: 65QM ** ON A/C NOT FOR ALL

1. Reason for the Job
Self Explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific	1	SAFETY BARRIER(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [64QM] (HOUSING-MLI, L WING TK OUTR)
540RB
FOR [65QM] (HOUSING-MLI, R WING TK OUTR)
640RB

C. Referenced Information

REFERENCE	DESIGNATION
TASK 28-10-00-910-001-A	Safety Procedures When You Do Work in a Fuel Tank
TASK 28-10-00-910-002-A	Access to the Fuel Tanks and the Work Areas
TASK 28-25-00-650-001-A	Pressure Defuel
TASK 28-25-00-650-003-A	To Drain Remaining Fuel from the Wing Tanks and the Center Tank
TASK 28-25-00-650-003-A-01	To Drain Remaining Fuel from the Wing Tanks and the Center Tank
TASK 57-27-11-000-002-A	Removal of the Access Panel
CMM 284330	(for corrective action)
Magnetic-Level-Indicator Assembly

3. Job Set-up
Subtask 28-43-22-941-051-A ** ON A/C NOT FOR ALL

A. Safety Precautions

WARNING: BEFORE YOU DO WORK IN OR NEAR A FUEL TANK, MAKE SURE THAT YOU OBEY ALL THE SAFETY PROCEDURES. THIS WILL PREVENT INJURY TO PERSONS AND/OR DAMAGE TO THE AIRCRAFT.

(1) You must obey the fuel safety procedures when you do work in a fuel tank (Ref. AMM TASK 28-10-00-910-001).
(2) Put the SAFETY BARRIER(S) in position.

Subtask 28-43-22-650-050-A ** ON A/C NOT FOR ALL

B. Fuel Configuration
(1) Defuel the applicable fuel tank (Ref. AMM TASK 28-25-00-650-001).
(2) Drain the remaining fuel from the applicable fuel tank (Ref. AMM TASK 28-25-00-650-003).

Subtask 28-43-22-010-050-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position below the applicable access panel 540RB (640RB).
(2) Remove the access panel (Ref. AMM TASK 57-27-11-000-002) and (Ref. AMM TASK 28-10-00-910-002):
(a) FOR [64QM] (HOUSING-MLI, L WING TK OUTR)
remove 540RB
(b) FOR [65QM] (HOUSING-MLI, R WING TK OUTR)
remove 640RB.

4. Procedure
Subtask 28-43-22-020-051-B ** ON A/C NOT FOR ALL

A. Removal of the Magnetic Level-Indicator Assembly 64QM (65QM)
(1) Remove the nuts (3) from the bolts (6).
(2) Remove the bolts (6) from the magnetic level-indicator housing (2).
(3) Remove the magnetic level-indicator assembly (7) from the access panel.

NOTE: If the MLI is removed with a loose or damaged top-stop (8), refer to CMM 284330 for repair instructions.

(4) Remove and discard the O-ring seals (4) and (5).

[Rev.10 from 2021] 2026.04.02 06:18:13 UTC