W DOC AIRBUS | AMM A320F

Installation of the Floodlight

TASK 28-25-54-400-001-A
Installation of the Floodlight

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
WARNING: MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING NOTICES ARE IN POSITION.
WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.
FIN: 32QU
1. Reason for the Job
Self Explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
ACCESS PLATFORM 3M (10 FT)
No specific
AR
SAFETY BARRIER(S)
No specific
AR
TIE WRAP
No specific
AR
WARNING NOTICE(S)
98D27803500001
1
LOCKING TOOL ZERO POS
 B. Consumable Materials
REFERENCE
DESIGNATION
(Material No.08BAA9)
Non Aqueous Cleaner-General - -
(Material No.12ACC1)
Corrosion Preventive Compound-Heavy Duty Soft Film -
(Material No.14SBA1)
Textile-Lint free Cotton -
 C. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
622KB
192MB
 D. Referenced Information
REFERENCE
DESIGNATION
TASK 24-41-00-861-002-A
Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01
Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02
Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A
De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01
De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02
De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
F Floodlight 32QU ** ON A/C NOT FOR ALL
F Floodlight 32QU ** ON A/C NOT FOR ALL
3. Job Set-up
Subtask 28-25-54-941-053-A ** ON A/C NOT FOR ALL
A. Safety Precautions
   (1) Make sure that the SAFETY BARRIER(S) are in position.
Subtask 28-25-54-860-051-A ** ON A/C NOT FOR ALL
B. Aircraft Maintenance Configuration
   (1) Make sure that the access door 192MB is open.
NOTE: If operating in battery power, do not keep the door open longer than necessary because the battery can discharge.
Subtask 28-25-54-941-053-B ** ON A/C NOT FOR ALL
C. Safety Precautions
   (1) Make sure that the SAFETY BARRIER(S) are in position.
   (2) Make sure that the WARNING NOTICE(S) is in position to tell persons not to operate the slats for the doors 622KB.
Subtask 28-25-54-860-051-B ** ON A/C NOT FOR ALL
D. Aircraft Maintenance Configuration
   (1) Make sure that the ACCESS PLATFORM 3M (10 FT) is below zone 622.
   (2) Make sure that the access door 622KB is open.
NOTE: If operating in battery power, do not keep the door open longer than necessary because the battery can discharge.
   (3) Make sure that the 98D27803500001 LOCKING TOOL ZERO POS is on the slat/flap control lever.
Subtask 28-25-54-865-051-A
E. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
121VUFUEL/RFL/DFL/SPLY2QUL24
** ON A/C NOT FOR ALL
121VUFUEL/RFL/DFL/SPLY2QUL23
** ON A/C ALL
122VUELEC/REFLNG/NORM2PRS27
122VUELEC/REFLNG/ON/BAT1PRU28
4. Procedure
Subtask 28-25-54-420-051-A
A. Preparation for Installation
   (1) Clean the component interface and/or the adjacent area with a Textile-Lint free Cotton - (Material No.14SBA1) made moist with Non Aqueous Cleaner-General - - (Material No.08BAA9) .
   (2) Make sure that the parts retained from the removed component are clean and in the correct condition.
   (3) Do an inspection of the component interfaces and the adjacent area.
Subtask 28-25-54-420-050-A
B. Installation of the Floodlight 32QU
   (1) Install the lamp (6) in the lamp holder (3) and install the screws (5).
   (2) Put the lamp holder (3) in position on the bracket (2).
   (3) Install the screws (4).
   (4) Connect the electrical wires to the lamp (6).
   (5) Install the cap (1) on the lamp (6).
   (6) Safety the electrical cables and the cap (1) to the lamp (6) with a TIE WRAP.
   (7) Clean the lens of the lamp (6) with a Textile-Lint free Cotton - (Material No.14SBA1) .
Subtask 28-25-54-865-052-A
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
121VUFUEL/RFL/DFL/SPLY2QUL24
** ON A/C NOT FOR ALL
121VUFUEL/RFL/DFL/SPLY2QUL23
** ON A/C ALL
122VUELEC/REFLNG/NORM2PRS27
122VUELEC/REFLNG/ON/BAT1PRU28
Subtask 28-25-54-861-050-A
D. Energize the Electrical Circuits
   (1) Energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-861-002)
Subtask 28-25-54-710-050-A ** ON A/C NOT FOR ALL
E. Test
   (1) Close the access door 192MB.
   (2) Open the access door 192MB and make sure that the lamp (6) comes on.
Subtask 28-25-54-710-050-B ** ON A/C NOT FOR ALL
E. Test
   (1) Close the access panel 622KB.
   (2) Open the access panel 622KB and make sure that the lamp (6) comes on.
Subtask 28-25-54-916-050-A
F. Application of Special Materials
   (1) Apply a layer of Corrosion Preventive Compound-Heavy Duty Soft Film - (Material No.12ACC1) to the screws (4) and the screws (5).
5. Close-up
Subtask 28-25-54-410-050-A ** ON A/C NOT FOR ALL
A. Close Access
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Close the access door 192MB.
Subtask 28-25-54-410-050-B ** ON A/C NOT FOR ALL
A. Close Access
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Close the access door 622KB.
Subtask 28-25-54-862-050-A
B. De-energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-862-002).
Subtask 28-25-54-942-050-A ** ON A/C NOT FOR ALL
C. Removal of Equipment
   (1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
Subtask 28-25-54-942-050-B ** ON A/C NOT FOR ALL
C. Removal of Equipment
   (1) Remove the 98D27803500001 LOCKING TOOL ZERO POS from the slat/flap control lever.
   (2) Remove the WARNING NOTICE(S).
   (3) Remove the access platform(s).
   (4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
[Rev.10 from 2021] 2026.04.02 06:17:43 UTC
"WTRUIB" 2025