W DOC AIRBUS | AMM A320F

Removal of the Refuel Valve Canister

TASK 28-25-52-000-001-A
Removal of the Refuel Valve Canister

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND THE RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.
FIN: 19QM
FIN: 20QM
1. Reason for the Job
Self explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
ACCESS PLATFORM 4M (13 FT)
No specific
AR
PLUG - BLANKING
No specific
AR
SAFETY BARRIER(S)
No specific
AR
SAFETY CLIP - CIRCUIT BREAKER
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
FOR [19QM] (CANISTER-REFUEL VALVE, L WING TK)
540JB
FOR [20QM] (CANISTER-REFUEL VALVE, R WING TK)
640JB
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 28-10-00-910-001-A
Safety Procedures When You Do Work in a Fuel Tank
TASK 28-10-00-910-002-A
Access to the Fuel Tanks and the Work Areas
TASK 28-25-00-650-001-A
Pressure Defuel
TASK 28-25-00-650-003-A
To Drain Remaining Fuel from the Wing Tanks and the Center Tank
TASK 28-25-00-650-003-A-01
To Drain Remaining Fuel from the Wing Tanks and the Center Tank
TASK 28-25-51-000-001-A
Removal of the Refuel Valve
TASK 57-27-11-000-002-A
Removal of the Access Panel
F Refuel Valve Canister 19QM(20QM)
3. Job Set-up
Subtask 28-25-52-941-051-A
A. Safety Precautions
WARNING: BEFORE YOU DO WORK IN OR NEAR A FUEL TANK, MAKE SURE THAT YOU OBEY ALL THE SAFETY PROCEDURES. THIS WILL PREVENT INJURY TO PERSONS AND/OR DAMAGE TO THE AIRCRAFT.
   (1) You must obey the fuel safety procedures (Ref. AMM TASK 28-10-00-910-001) when you do work in a fuel tank.
   (2) Put the SAFETY BARRIER(S) in position.
Subtask 28-25-52-650-050-A
B. Fuel Configuration
   (1) Defuel the applicable fuel tank (Ref. AMM TASK 28-25-00-650-001).
   (2) Drain the remaining fuel from the applicable fuel tank (Ref. AMM TASK 28-25-00-650-003).
Subtask 28-25-52-865-050-A
C. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
121VUFUEL/RFL/DFL/SPLY2QUL24
121VUFUEL/RFL/DFL/XFR/DEFUEL/VALVE1QUL23
** ON A/C NOT FOR ALL
121VUFUEL/RFL/DFL/SPLY2QUL23
121VUFUEL/RFL/DFL/XFR/DEFUEL/VALVE1QUL22
Subtask 28-25-52-010-050-A
D. Get Access
   (1) Put the ACCESS PLATFORM 4M (13 FT) in position below the applicable access panel 540JB (640JB).
   (2) Remove the applicable wing access panel (Ref. AMM TASK 28-10-00-910-002), (Ref. AMM TASK 57-27-11-000-002):

     (a) FOR [19QM] (CANISTER-REFUEL VALVE, L WING TK)
remove 540JB

     (b) FOR [20QM] (CANISTER-REFUEL VALVE, R WING TK)
remove 640JB.
   (3) Remove the refuel valve (Ref. AMM TASK 28-25-51-000-001).
4. Procedure
Subtask 28-25-52-020-054-A
A. Removal of the Refuel Valve Canister 19QM (20QM)
   (1) Remove the nut (4), the screw (5) and disconnect the bonding straps (1) and (6).
   (2) Remove the bolts (2) and disconnect the adapter (14).
   (3) Remove and discard the O-ring (3).
   (4) Remove the bolts (9) and disconnect the elbow (8).
   (5) Remove and discard the O-ring (7).
   (6) Put the PLUG-BLANKING in each disconnected line end.
   (7) Remove the screws (12) and the spacer (13).
   (8) Remove the refuel valve canister (10).
   (9) Remove and discard the O-ring (11).
[Rev.10 from 2021] 2026.04.02 06:17:42 UTC
"WTRUIB" 2025