W DOC AIRBUS | AMM A320F

Removal of the Refuel Light

TASK 28-25-48-000-001-A
Removal of the Refuel Light

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND THE RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
FIN: 30QU1 ** ON A/C NOT FOR ALL
FIN: 30QU2 ** ON A/C NOT FOR ALL
1. Reason for the Job
Self explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
1
ACCESS PLATFORM 4M (13 FT)
No specific
AR
CAP - BLANKING
No specific
AR
SAFETY BARRIER(S)
No specific
AR
SAFETY CLIP - CIRCUIT BREAKER
No specific
AR
WARNING NOTICE(S)
98D27803500001
1
LOCKING TOOL ZERO POS
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
522JB, 622JB
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 28-00-00-910-001-A
Fuel Safety Procedures
F Ready-to-Refuel Light Assembly
3. Job Set-up
Subtask 28-25-48-941-050-D ** ON A/C NOT FOR ALL
A. Safety Precautions
WARNING: OBEY THE FUEL SAFETY PROCEDURES.
   (1) You must obey the fuel safety procedures when you do work on the fuel system (Ref. AMM TASK 28-00-00-910-001).
   (2) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
   (3) Put a WARNING NOTICE(S) in the cockpit to tell persons not to operate the slats.
   (4) Install the 98D27803500001 LOCKING TOOL ZERO POS on the slat/flap control lever.
Subtask 28-25-48-865-053-A ** ON A/C NOT FOR ALL
B. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/SLT/CTL AND MONG/SYS15CVB06
121VUFUEL/FQI/CHANNEL/1 AND 28QTL26
121VUFUEL/RFL/DFL/SPLY2QUL24
121VUFUEL/RFL/DFL/XFR/DEFUEL/VALVE1QUL23
121VUFLIGHT CONTROLS/SLT/CTL/SYS27CVR21
Subtask 28-25-48-010-050-B ** ON A/C NOT FOR ALL
C. Get Access
   (1) Put the ACCESS PLATFORM 4M (13 FT) in position below the applicable zone 522, 622.
   (2) Remove the applicable access panel:
4. Procedure
Subtask 28-25-48-020-050-D ** ON A/C NOT FOR ALL
A. Removal of the Refuel Light
CAUTION: HOLD THE LENSES IN POSITION WHEN YOU REMOVE THE ATTACHMENT SCREWS, OR THE LENSES CAN FALL OUT.
   (1) Remove the nuts (6) and the bolts (7) from the clamps (5).
   (2) Remove the clamps (5) from the electrical cable (3).
CAUTION: MAKE SURE THAT THE ELECTRICAL CONNECTORS ARE CLEAN BEFORE YOU DISCONNECT OR CONNECT THEM. CONTAMINATION ON THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO EQUIPMENT.
   (3) Disconnect the electrical connector (4) from the receptacle.
   (4) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
   (5) Remove the screws (9), ready-to-refuel light (8), green lens (11) and the clear lens (10) from the panel (2).
[Rev.9 from 2019] 2026.04.02 06:17:41 UTC
"WTRUIB" 2025