Reactivation of the Center Tank
TASK 28-21-00-440-002-A
Reactivation of the Center Tank
A. Fixtures, Tools, Test and Support Equipment
B. Referenced Information
3. Job Set-up
Subtask 28-21-00-941-085-A ** ON A/C NOT FOR ALL
Subtask 28-21-00-440-050-A ** ON A/C NOT FOR ALL
Subtask 28-21-00-650-066-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.02 07:02:44 UTC
Reactivation of the Center Tank
WARNING:
MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING NOTICES ARE IN POSITION.
WARNING:
MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.
1. Reason for the JobNOTE: This reactivation task is not related to an AFM-CDL/MMEL item.
NOTE: This task is to be used to reactivate the center tank after deactivation (Ref. TASK 28-21-00-040-002).
2. Job Set-up InformationA. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | SAFETY BARRIER(S) |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 12-11-28-650-003-A | Pressure Refuel with Automatic Control |
| TASK 28-00-00-910-001-A | Fuel Safety Procedures |
| TASK 28-11-00-790-003-A | Leak Test of the Center Tank |
| TASK 28-21-51-400-002-A | Installation of the Fuel Pumps |
| TASK 28-25-00-650-001-A | Pressure Defuel |
| TASK 28-25-00-869-001-A | Fuel Transfer |
Subtask 28-21-00-941-085-A ** ON A/C NOT FOR ALL
A. Safety Precautions
(2) Make sure that the SAFETY BARRIER(S) are in position.
4. ProcedureWARNING:
OBEY THE FUEL SAFETY PROCEDURES.
(1) You must obey the fuel safety procedures when you do work on the fuel system (Ref. AMM TASK 28-00-00-910-001). (2) Make sure that the SAFETY BARRIER(S) are in position.
Subtask 28-21-00-440-050-A ** ON A/C NOT FOR ALL
A. Reactivation of the Center Tank
(1) Connect the electrical connector (1) to the center tank refuel valve 10QU.
(2) Connect the electrical connector (2) to the center tank pumps 37QA(38QA).
Subtask 28-21-00-865-076-A ** ON A/C NOT FOR ALL (1) Connect the electrical connector (1) to the center tank refuel valve 10QU.
(2) Connect the electrical connector (2) to the center tank pumps 37QA(38QA).
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
Subtask 28-21-00-710-076-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| FOR FIN: 37QA (PUMPFUEL NO 1, CTR TK) | |||
| 121VU | FUEL/CTR TK/PUMP1 SPLY | 29QA | P23 |
| FOR FIN: 38QA (PUMPFUEL NO 2, CTR TK) | |||
| 121VU | FUEL/CTR TK/PUMP2 SPLY | 30QA | P26 |
C. Test
(1) Do a test of the refuel valve 10QU as follows:
(a) Refuel or transfer fuel into the center tank as necessary (Ref. AMM TASK 12-11-28-650-003) or (Ref. AMM TASK 28-25-00-869-001).
(b) Make sure that:
(3) Do a leak test of the center tank (Ref. AMM TASK 28-11-00-790-003).
(4) Make an entry in the aircraft technical log that the center tank has been reactivated.
5. Close-up(1) Do a test of the refuel valve 10QU as follows:
(a) Refuel or transfer fuel into the center tank as necessary (Ref. AMM TASK 12-11-28-650-003) or (Ref. AMM TASK 28-25-00-869-001).
(b) Make sure that:
- the fuel quantity in the center tank increases correctly
- there are no leaks from the refuel valve.
(3) Do a leak test of the center tank (Ref. AMM TASK 28-11-00-790-003).
(4) Make an entry in the aircraft technical log that the center tank has been reactivated.
Subtask 28-21-00-650-066-A ** ON A/C NOT FOR ALL
A. Fuel Configuration
(1) Refuel, defuel or transfer fuel as necessary (Ref. AMM TASK 12-11-28-650-003), (Ref. AMM TASK 28-25-00-650-001) or (Ref. AMM TASK 28-25-00-869-001).
Subtask 28-21-00-942-091-A ** ON A/C NOT FOR ALL (1) Refuel, defuel or transfer fuel as necessary (Ref. AMM TASK 12-11-28-650-003), (Ref. AMM TASK 28-25-00-650-001) or (Ref. AMM TASK 28-25-00-869-001).
B. Removal of Equipment
(1) Remove the safety barrier.
(2) Remove the WARNING NOTICE(S).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(1) Remove the safety barrier.
(2) Remove the WARNING NOTICE(S).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
Refuel Valve 10QU - Electrical connector