W DOC AIRBUS | AMM A320F

Installation of the Actuator

TASK 28-15-51-400-002-A
Installation of the Actuator

WARNING: MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING NOTICES ARE IN POSITION.
WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.
WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
  • DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
  • DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
  • MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
FIN: 11QP ** ON A/C NOT FOR ALL
FIN: 12QP ** ON A/C NOT FOR ALL
1. Reason for the Job
Self Explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
SAFETY BARRIER(S)
No specific
AR
WARNING NOTICE(S)
No specific
Torque wrench: range to between .113 and .102 m.daN (10.00 and 9.03 lbf.in ) T
 B. Consumable Materials
REFERENCE
DESIGNATION
(Material No.03GEE1)
Synthetic Oil base Grease-Fuel and Oxidized Environment Fluorinated -
(Material No.08BAA9)
Non Aqueous Cleaner-General - -
(Material No.14SBA1)
Textile-Lint free Cotton -
 C. Expendable Parts
FIG.ITEM
DESIGNATION
IPC-CSN
6
O-RING
AIPC 28-15-42-01-010
 D. Referenced Information
REFERENCE
DESIGNATION
TASK 27-50-00-866-008-A
Extension of the Flaps on the Ground
TASK 27-50-00-866-008-A-01
Extension of the Flaps/Slats on the Ground
TASK 27-50-00-866-009-A
Retraction of the Flaps on the Ground
TASK 27-50-00-866-009-A-01
Retraction of the Flaps/Slats on the Ground
TASK 27-60-00-866-002-A
Extension-Retraction of the Spoilers for Maintenance
TASK 28-15-00-740-002-A
Functional (BITE) Test of the Intercell Transfer Valves
F Transfer Valve Actuators
3. Job Set-up
Subtask 28-15-51-941-057-A ** ON A/C NOT FOR ALL
A. Safety Precautions
   (1) Make sure that the SAFETY BARRIER(S) are in position.
   (2) Make sure that the WARNING NOTICE(S) is in position to tell persons not to operate the flight controls.
Subtask 28-15-51-865-055-A ** ON A/C NOT FOR ALL
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUFUEL/XFR VALVE1/WING/R2QPA11
49VUFUEL/XFR VALVE1/WING/L1QPA10
121VUFUEL/XFR VALVE2/WING/R4QPM23
121VUFUEL/XFR VALVE2/WING/L3QPM22
Subtask 28-15-51-860-054-A ** ON A/C NOT FOR ALL
C. Aircraft Maintenance Configuration
   (1) Make sure that the flaps are fully extended (Ref. AMM TASK 27-50-00-866-008).
   (2) Make sure that the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION is on the flap/slat control lever.
   (3) Make sure that the No. 3 spoiler is extended (Ref. AMM TASK 27-60-00-866-002).
   (4) Make sure that the 98D27604000000 COLLAR-SAFETY, SPOILER or 98D27604004000 COLLAR SAFETY SPOILER is on the applicable spoiler servo-control.
   (5) Make sure the access platform is below zone 575(675).
4. Procedure
CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
  • DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
  • DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
  • MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 28-15-51-420-054-A ** ON A/C NOT FOR ALL
A. Preparation for Installation
   (1) Clean the component interfaces and the adjacent areas with a Textile-Lint free Cotton - (Material No.14SBA1) made moist with Non Aqueous Cleaner-General - - (Material No.08BAA9) .
   (2) Make sure that the parts retained from the removed component are clean and in the correct condition.
   (3) Do an inspection of the component interfaces and the adjacent area.
   (4) Apply Synthetic Oil base Grease-Fuel and Oxidized Environment Fluorinated - (Material No.03GEE1) to the new AIPC 28-15-42-01-010 O-RING (6).
Subtask 28-15-51-420-051-A ** ON A/C NOT FOR ALL
B. Installation of Actuator 11QP(12QP)
CAUTION: MAKE SURE THAT YOU CORRECTLY ALIGN THE POSITIONS OF THE ROLL PIN ON THE DRIVE SPINDLE AND THE PIN HOLE IN THE ACTUATOR. IF NOT, THE ACTUATOR WILL NOT OPERATE THE VALVE CORRECTLY AND CAN CAUSE FUEL LEAKAGE.
   (1) Make sure the transfer-valve drive slot moves freely.
   (2) Align the transfer-valve drive slot with the transfer valve actuator (5).
   (3) Install the new O-ring (6) on the transfer valve drive (1).
   (4) Carefully engage the transfer valve actuator (5) on the transfer-valve drive (1).
     (a) Make sure that the mating surfaces of the actuator (5) and the transfer valve drive (1) engage correctly.
     (b) Make sure that there is zero clearance (around all of the circumference) between the flange of the:
  • actuator (5)
  • transfer valve drive (1).
NOTE: There will always be no clearance when the pins and the grooves are all correctly aligned.
   (5) Put the clamp (3) and install the bolt (2).
CAUTION: DO NOT TORQUE THE V-CLAMP(S) TO MORE THAN THE SPECIFIED VALUE. THIS PREVENTS DAMAGE TO THE FLANGE SURFACES.
   (6) TORQUE the bolt (2) to between .113 and .102 m.daN (10.00 and 9.03 lbf.in ) T.
   (7) Make sure that the clamp (3) is fully engaged.
NOTE: The clamp (3) is fully engaged if no part of the flange shows for the:
  • actuator (5)
  • transfer valve drive (1).
   (8) Remove the blanking caps and install the electrical connector (4).
Subtask 28-15-51-865-056-A ** ON A/C NOT FOR ALL
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUFUEL/XFR VALVE1/WING/R2QPA11
49VUFUEL/XFR VALVE1/WING/L1QPA10
121VUFUEL/XFR VALVE2/WING/R4QPM23
121VUFUEL/XFR VALVE2/WING/L3QPM22
Subtask 28-15-51-710-051-A ** ON A/C NOT FOR ALL
D. Operational Test
   (1) Do a BITE of the intercell transfer valves (Ref. AMM TASK 28-15-00-740-002).
5. Close-up
Subtask 28-15-51-860-053-A ** ON A/C NOT FOR ALL
A. Aircraft Configuration
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Retract the Spoiler No. 3 (Ref. AMM TASK 27-60-00-866-002).
   (3) On the spoiler servo-control, make sure that the pointer on the hex. head is opposite the letter 'O' on the housing.
   (4) Retract the flaps fully (Ref. AMM TASK 27-50-00-866-009).
Subtask 28-15-51-942-053-A ** ON A/C NOT FOR ALL
B. Removal of Equipment
   (1) Remove the safety barriers.
   (2) Remove the WARNING NOTICE(S).
   (3) Remove the access platform(s).
   (4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
[Rev.10 from 2021] 2026.04.02 06:17:15 UTC
"WTRUIB" 2025