Operational Check of Individual Transfer Valves to Ensure Valve Shaft Rotates Valve to Open Position

TASK 28-15-00-710-002-A
Operational Check of Individual Transfer Valves to Ensure Valve Shaft Rotates Valve to Open Position

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

ZONE: 210

1. Reason for the Job
Refer to the MPD TASK: 281500-01
OPERATIONAL CHECK OF INDIVIDUAL TRANSFER VALVES TO ENSURE VALVE SHAFT ROTATES VALVE TO OPEN POSITION

NOTE: This task also gives step(s) for the aircrafts with the ACT(s) installed. You can ignore the step(s) if it is not applicable for you.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	SAFETY BARRIER(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
210	CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD

C. Referenced Information

REFERENCE	DESIGNATION
TASK 12-11-28-650-003-A	Pressure Refuel with Automatic Control
TASK 28-00-00-910-001-A	Fuel Safety Procedures
TASK 28-25-00-650-001-A	Pressure Defuel
TASK 31-32-00-860-001-A	Procedure to Get Access to the SYSTEM REPORT/TEST Menu Page
TASK 31-60-00-860-001-A	EIS Start Procedure
TASK 31-60-00-860-002-A	EIS Stop Procedure

3. Job Set-up
Subtask 28-15-00-941-053-A ** ON A/C NOT FOR ALL

A. Safety Precautions

WARNING: OBEY THE FUEL SAFETY PROCEDURES.

(1) You must obey the fuel safety procedures when you do work on the fuel system (Ref. AMM TASK 28-00-00-910-001).
(2) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.

Subtask 28-15-00-860-053-A ** ON A/C NOT FOR ALL

B. Aircraft Maintenance Configuration

NOTE: This procedure also gives step(s) for the aircrafts with the ACT(s) installed. You can ignore the step(s) if it is not applicable for you.

(1) Make sure that each wing contains a minimum fuel level of 1800 kg (3968.3 lb). Make sure that each wing tank outer cell is full of fuel. If required, refuel the aircraft (Ref. AMM TASK 12-11-28-650-003) to get the minimum fuel level.
(2) Make sure that the refuel panel door is open and the MODE SEL switch (on the panel 800VU) is in the REFUEL position.
(3) Energize the ECAM system (Ref. AMM TASK 31-60-00-860-001).
(4) On the ECAM control panel, push (in) the FUEL pushbutton switch (P/BSW).
(5) On the ECAM System Display (SD), make sure that the FUEL page is shown.
(6) On the ECAM SD FUEL page, make sure that the intercell transfer valves show closed.
(7) Get access to the SYSTEM REPORT/TEST Menu Page (Ref. AMM TASK 31-32-00-860-001).
(8) When the SYSTEM REPORT/TEST Menu page comes into view, do this procedure:

ACTION	RESULT
1.Push the line key adjacent to the FUEL indication.	the FUEL Main Menu first page comes into view.
2.On the MCDU control panel push the NEXT PAGE key.	the FUEL Main Menu second page comes into view.
3.Push the line key adjacent to the INPUT PARAMETER VALUES indication.	the MCDU shows the page FQIS INPUT PARAMETERS.
4.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page FQIS PROBE CAPACITANCES.
5.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page ACT PROBE CAPACITANCES.
6.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page FQIS DISCRETE INPUTS.
7.On the MCDU: - identify and monitor the left inner low level sensor LS1 (16QJ1) bit indicator P3	On the MCDU, make sure that: - the P3 indication is '1' (sensor is wet)
- identify and monitor the right inner low level sensor LS5 (16QJ2) bit indicator P4	- the P4 indication is '1' (sensor is wet)
- identify and monitor the left inner FWD LO LVL sensor LS5 (15QJ1) bit indicator L6	- the L6 indication is '1' (sensor is wet)
- identify and monitor the right inner low level sensor LS1 (15QJ2) bit indicator M7	- the M7 indication is '1' (sensor is wet)
- identify and monitor the L LO LVL INR MID sensor LS2 (39QJ1) bit indicator L5	- the L5 indication is '1' (sensor is wet)
- identify and monitor the R LO LVL INR MID sensor LS2 (39QJ2) bit indicator P6.	- the P6 indication is '1' (sensor is wet).

Subtask 28-15-00-860-053-C ** ON A/C NOT FOR ALL

B. Aircraft Maintenance Configuration

NOTE: This procedure also gives step(s) for the aircrafts with the ACT(s) installed. You can ignore the step(s) if it is not applicable for you.

ACTION	RESULT
1.Push the line key adjacent to the FUEL indication.	the FUEL Main Menu first page comes into view.
2.Push the line key adjacent to the INPUT PARAMETER VALUES indication.	the MCDU shows the page FQIS INPUT PARAMETERS.
3.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page FQIS PROBE CAPACITANCES.
4.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page ACT PROBE CAPACITANCES.
5.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page FQIS DISCRETE INPUTS.
6.On the MCDU: - identify and monitor the left inner low level sensor LS1 (16QJ1) bit indicator A3	On the MCDU, make sure that: - the A3 indication is '1' (sensor is wet)
- identify and monitor the right inner low level sensor LS5 (16QJ2) bit indicator E3	- the E3 indication is '1' (sensor is wet)
- identify and monitor the left inner FWD LO LVL sensor LS5 (15QJ1) bit indicator E4	- the E4 indication is '1' (sensor is wet)
- identify and monitor the right inner low level sensor LS1 (15QJ2) bit indicator A4	- the A4 indication is '1' (sensor is wet)
- identify and monitor the L LO LVL INR MID sensor LS2 (39QJ1) bit indicator B4	- the B4 indication is '1' (sensor is wet)
- identify and monitor the R LO LVL INR MID sensor LS2 (39QJ2) bit indicator B3.	- the B3 indication is '1' (sensor is wet).

4. Procedure
Subtask 28-15-00-865-051-A ** ON A/C NOT FOR ALL

A. Table of the circuit breakers used in this procedure:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FUEL/XFR VALVE1/WING/R	2QP	A11
49VU	FUEL/XFR VALVE1/WING/L	1QP	A10
121VU	FUEL/XFR VALVE2/WING/R	4QP	M23
121VU	FUEL/XFR VALVE2/WING/L	3QP	M22

Subtask 28-15-00-710-053-C ** ON A/C NOT FOR ALL

B. Operational Check of Individual Transfer Valves to Ensure Drive Shaft Rotates Valve to Open Position

NOTE: During the test the ECAM will show unwanted indications, which you can ignore.

NOTE: This procedure also gives step(s) for the aircrafts with the ACT(s) installed. You can ignore the step(s) if it is not applicable for you.

ACTION	RESULT
1.Open, safety and tag the circuit breaker 3QP.	On the ECAM display unit (DU): the green right-wing transfer-valve indicator moves from the closed position to the open position the green left-wing transfer-valve indicator moves from the closed position to the intermediate (amber) position the right-wing outer-cell fuel content decreases and the right-wing inner-cell fuel content increases.

2.Remove the safety-clip and tag and close the circuit breaker 3QP.	On the ECAM DU: the green right-wing transfer-valve indicator moves from the open to the closed position the amber left-wing transfer-valve indicator moves from the intermediate to the closed (green) position the fuel movement to the right-wing inner-cell stops.

3.Open, safety and tag the circuit breaker 4QP.	On the ECAM display unit (DU): the green left-wing transfer-valve indicator moves from the closed position to the open position the green right-wing transfer-valve indicator moves from the closed position to the intermediate (amber) position the left-wing outer-cell fuel content decreases and the left-wing inner-cell fuel content increases.

4.Remove the safety-clip and tag and close the circuit breaker 4QP.	On the ECAM DU: the green left-wing transfer-valve indicator moves from the open to the closed position the amber right-wing transfer-valve indicator moves from the intermediate to the closed (green) position the fuel movement to the left-wing inner-cell stops.

5.Open, safety and tag the circuit breaker 2QP.	On the ECAM display unit (DU): the green left-wing transfer-valve indicator moves from the closed position to the open position the green right-wing transfer-valve indicator moves from the closed position to the intermediate (amber) position the left-wing outer-cell fuel content decreases and the left-wing inner-cell fuel content increases.

6.Remove the safety-clip and tag and close the circuit breaker 2QP.	On the ECAM DU: the green left-wing transfer-valve indicator moves from the open to the closed position the amber right-wing transfer-valve indicator moves from the intermediate to the closed (green) position the fuel movement to the left-wing inner-cell stops.

7.Open, safety and tag the circuit breaker 1QP.	On the ECAM display unit (DU): the green right-wing transfer-valve indicator moves from the closed position to the open position the green left-wing transfer-valve indicator moves from the closed position to the intermediate (amber) position the right-wing outer-cell fuel content decreases and the right-wing inner-cell fuel content increases.

8.Remove the safety-clip and tag and close the circuit breaker 1QP.	On the ECAM DU: the green right-wing transfer-valve indicator moves from the open to the closed position the amber left-wing transfer-valve indicator moves from the intermediate to the closed (green) position the fuel movement to the right-wing inner-cell stops.
9.Defuel each wing tank to keep a maximum fuel quantity of 500 kg (1100 lb) (Ref. AMM TASK 28-25-00-650-001).
10.Get access to the SYSTEM REPORT/TEST Menu Page (Ref. AMM TASK 31-32-00-860-001).	On the MCDU, make sure that the SYSTEM REPORT/TEST Menu page comes into view.
11.Push the line key adjacent to the FUEL indication.	the FUEL Main Menu first page comes into view.
12.On the MCDU control panel push the NEXT PAGE key.	the FUEL Main Menu second page comes into view.
13.Push the line key adjacent to the INPUT PARAMETER VALUES indication.	the MCDU shows the page FQIS INPUT PARAMETERS.
14.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page FQIS PROBE CAPACITANCES.
15.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page ACT PROBE CAPACITANCES.
16.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page FQIS DISCRETE INPUTS.
17.On the MCDU: - identify and monitor the left inner low level sensor LS1 (16QJ1) bit indicator P3	On the MCDU, make sure that: - the P3 indication is '0' (sensor is dry)
- identify and monitor the right inner low level sensor LS5 (16QJ2) bit indicator P4	- the P4 indication is '0' (sensor is dry)
- identify and monitor the left inner FWD LO LVL sensor LS5 (15QJ1) bit indicator L6	- the L6 indication is '0' (sensor is dry)
- identify and monitor the right inner low level sensor LS1 (15QJ2) bit indicator M7	- the M7 indication is '0' (sensor is dry)
- identify and monitor the L LO LVL INR MID sensor LS2 (39QJ1) bit indicator L5	- the L5 indication is '0' (sensor is dry)
- identify and monitor the R LO LVL INR MID sensor LS2 (39QJ2) bit indicator P6.	- the P6 indication is '0' (sensor is dry).

Subtask 28-15-00-710-053-E ** ON A/C NOT FOR ALL

B. Operational Check of Individual Transfer Valves to Ensure Drive Shaft Rotates Valve to Open Position

NOTE: During the test the ECAM will show unwanted indications, which you can ignore.

NOTE: This procedure also gives step(s) for the aircrafts with the ACT(s) installed. You can ignore the step(s) if it is not applicable for you.

ACTION	RESULT
1.Open, safety and tag the circuit breaker 3QP.	On the ECAM display unit (DU): the right-wing transfer-valve open symbol (green triangle) comes into view the left-wing transfer-valve intermediate position symbol (amber triangle) comes into view the right-wing outer-cell fuel content decreases and the right-wing inner-cell fuel content increases.

2.Remove the safety-clip and tag and close the circuit breaker 3QP.	On the ECAM DU: the right-wing transfer-valve open symbol goes out of view the left-wing transfer-valve intermediate position symbol goes out of view the fuel movement to the right-wing inner-cell stops.

3.Open, safety and tag the circuit breaker 4QP.	On the ECAM display unit (DU): the left-wing transfer-valve open symbol (green triangle) comes into view the right-wing transfer-valve intermediate position symbol (amber triangle) comes into view the left-wing outer-cell fuel content decreases and the left-wing inner-cell fuel content increases.

4.Remove the safety-clip and tag and close the circuit breaker 4QP.	On the ECAM DU: the left-wing transfer-valve open symbol goes out of view the right-wing transfer-valve intermediate position symbol goes out of view the fuel movement to the left-wing inner-cell stops.

5.Open, safety and tag the circuit breaker 2QP.	On the ECAM display unit (DU): the left-wing transfer-valve open symbol (green triangle) comes into view the right-wing transfer-valve intermediate position symbol (amber triangle) comes into view the left-wing outer-cell fuel content decreases and the left-wing inner-cell fuel content increases.

6.Remove the safety-clip and tag and close the circuit breaker 2QP.	On the ECAM DU: the left-wing transfer-valve open symbol goes out of view the right-wing transfer-valve intermediate position symbol goes out of view the fuel movement to the left-wing inner-cell stops.

7.Open, safety and tag the circuit breaker 1QP.	On the ECAM display unit (DU): the right-wing transfer-valve open symbol (green triangle) comes into view the left-wing transfer-valve intermediate position symbol (amber triangle) comes into view the right-wing outer-cell fuel content decreases and the right-wing inner-cell fuel content increases.

8.Remove the safety-clip and tag and close the circuit breaker 1QP.	On the ECAM DU: the right-wing transfer-valve open symbol goes out of view the left-wing transfer-valve intermediate position symbol goes out of view the fuel movement to the right-wing inner-cell stops.
9.Defuel each wing tank to keep a maximum fuel quantity of 500 kg (1100 lb) (Ref. AMM TASK 28-25-00-650-001).
10.Get access to the SYSTEM REPORT/TEST Menu Page (Ref. AMM TASK 31-32-00-860-001).	On the MCDU, make sure that the SYSTEM REPORT/TEST Menu page comes into view.
11.Push the line key adjacent to the FUEL indication.	the FUEL Main Menu first page comes into view.
12.On the MCDU control panel push the NEXT PAGE key.	the FUEL Main Menu second page comes into view.
13.Push the line key adjacent to the INPUT PARAMETER VALUES indication.	the MCDU shows the page FQIS INPUT PARAMETERS.
14.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page FQIS PROBE CAPACITANCES.
15.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page ACT PROBE CAPACITANCES.
16.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page FQIS DISCRETE INPUTS.
17.On the MCDU: - identify and monitor the left inner low level sensor LS1 (16QJ1) bit indicator P3	On the MCDU, make sure that: - the P3 indication is '0' (sensor is dry)
- identify and monitor the right inner low level sensor LS5 (16QJ2) bit indicator P4	- the P4 indication is '0' (sensor is dry)
- identify and monitor the left inner FWD LO LVL sensor LS5 (15QJ1) bit indicator L6	- the L6 indication is '0' (sensor is dry)
- identify and monitor the right inner low level sensor LS1 (15QJ2) bit indicator M7	- the M7 indication is '0' (sensor is dry)
- identify and monitor the L LO LVL INR MID sensor LS2 (39QJ1) bit indicator L5	- the L5 indication is '0' (sensor is dry)
- identify and monitor the R LO LVL INR MID sensor LS2 (39QJ2) bit indicator P6.	- the P6 indication is '0' (sensor is dry).

Subtask 28-15-00-710-053-F ** ON A/C NOT FOR ALL

B. Operational Check of Individual Transfer Valves to Ensure Drive Shaft Rotates Valve to Open Position

NOTE: During the test the ECAM will show unwanted indications, which you can ignore.

NOTE: This procedure also gives step(s) for the aircrafts with the ACT(s) installed. You can ignore the step(s) if it is not applicable for you.

ACTION	RESULT
1.Open, safety and tag the circuit breaker 3QP.	On the ECAM display unit (DU): the right-wing transfer-valve open symbol (green triangle) comes into view the left-wing transfer-valve intermediate position symbol (amber triangle) comes into view The right-wing outer-cell fuel content decreases and the right-wing inner-cell fuel content increases.

2.Remove the safety-clip and tag and close the circuit breaker 3QP.	On the ECAM DU: the right-wing-transfer-valve open symbol goes out of view the left-wing transfer-valve intermediate position symbol goes out of view the fuel movement to the right-wing inner-cell stops.

3.Open, safety and tag the circuit breaker 4QP.	On the ECAM display unit (DU): the left-wing transfer-valve open symbol (green triangle) comes into view the right-wing transfer-valve intermediate position symbol (amber triangle) comes into view the left-wing outer-cell fuel content decreases and the left-wing inner-cell fuel content increases.

4.Remove the safety-clip and tag and close the circuit breaker 4QP.	On the ECAM DU: the left-wing transfer-valve open symbol goes out of view the right-wing transfer-valve intermediate position symbol goes out of view the fuel movement to the left-wing inner-cell stops.

5.Open, safety and tag the circuit breaker 2QP.	On the ECAM display unit (DU): the left-wing transfer-valve open-symbol (green triangle) comes into view the right-wing transfer-valve intermediate position symbol (amber triangle) comes into view the left-wing outer-cell fuel content decreases and the left-wing inner-cell fuel content increases.

6.Remove the safety-clip and tag and close the circuit breaker 2QP.	On the ECAM DU: the left-wing transfer-valve open symbol goes out of view the right-wing transfer-valve intermediate position symbol goes out of view the fuel movement to the left-wing inner-cell stops.

7.Open, safety and tag the circuit breaker 1QP.	On the ECAM display unit (DU): the right-wing transfer-valve open symbol (green triangle) comes into view the left-wing transfer-valve intermediate position symbol (amber triangle) comes into view the right-wing outer-cell fuel content decreases and the right-wing inner-cell fuel content increases.

8.Remove the safety-clip and tag and close the circuit breaker 1QP.	On the ECAM DU: the right-wing transfer-valve open symbol goes out of view the left-wing transfer-valve intermediate position symbol goes out of view the fuel movement to the right-wing inner-cell stops.
9.Defuel each wing tank to keep a maximum fuel quantity of 500 kg (1100 lb) (Ref. AMM TASK 28-25-00-650-001).
10.Get access to the SYSTEM REPORT/TEST Menu Page (Ref. AMM TASK 31-32-00-860-001).	On the MCDU, make sure that the SYSTEM REPORT/TEST Menu page comes into view.
11.Push the line key adjacent to the FUEL indication.	the FUEL Main Menu first page comes into view.
12.Push the line key adjacent to the INPUT PARAMETER VALUES indication.	the MCDU shows the page FQIS INPUT PARAMETERS.
13.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page FQIS PROBE CAPACITANCES.
14.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page ACT PROBE CAPACITANCES.
15.On the MCDU control panel push the NEXT PAGE key.	- the MCDU shows the page FQIS DISCRETE INPUTS.
16.On the MCDU: - identify and monitor the left inner low level sensor LS1 (16QJ1) bit indicator A3	On the MCDU, make sure that: - the A3 indication is '0' (sensor is dry)
- identify and monitor the right inner low level sensor LS5 (16QJ2) bit indicator E3	- the E3 indication is '0' (sensor is dry)
-identify and monitor the left inner FWD LO LVL sensor LS5 (15QJ1) bit indicator E4	- the E4 indication is '0' (sensor is dry)
- identify and monitor the right inner low level sensor LS1 (15QJ2) bit indicator A4	- the A4 indication is '0' (sensor is dry)
- identify and monitor the L LO LVL INR MID sensor LS2 (39QJ1) bit indicator B4	- the B4 indication is '0' (sensor is dry)
- identify and monitor the R LO LVL INR MID sensor LS2 (39QJ2) bit indicator B3.	- the B3 indication is '0' (sensor is dry).

5. Close-up
Subtask 28-15-00-860-052-A ** ON A/C NOT FOR ALL

A. Aircraft Configuration
(1) Refuel, defuel or transfer fuel as necessary (Ref. AMM TASK 12-11-28-650-003), (Ref. AMM TASK 28-25-00-650-001) or (Ref. AMM TASK 12-11-28-650-003).
(2) Make sure that the MODE SEL switch (on the panel 800VU) is in the OFF and guarded position.
(3) Make sure that the refuel/defuel panel door is closed.
(4) Do the EIS stop procedure (Ref. AMM TASK 31-60-00-860-002).

Subtask 28-15-00-942-051-A ** ON A/C NOT FOR ALL

B. Removal of Equipment
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the safety barriers.
(3) Remove the access platform(s).
(4) Remove the WARNING NOTICE(S).
(5) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.04.02 06:17:14 UTC