Removal of the Gravity Fill Cap/Adaptor

TASK 28-11-43-000-001-A
Removal of the Gravity Fill Cap/Adaptor

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

FIN: 42QM ** ON A/C NOT FOR ALL
FIN: 43QM ** ON A/C NOT FOR ALL
FIN: 44QM ** ON A/C NOT FOR ALL
FIN: 45QM ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE
No specific	AR	SAFETY BARRIER(S)
98D28004000000	1	SPANNER-OVERWING FILLER

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [42QM] (ADAPTER-OVERWING REFUEL, L)
FOR [44QM] (CAP-OVERWING REFUEL, L)
540PB
FOR [43QM] (ADAPTER-OVERWING REFUEL, R)
FOR [45QM] (CAP-OVERWING REFUEL, R)
640PB

C. Referenced Information

REFERENCE	DESIGNATION
TASK 28-10-00-910-001-A	Safety Procedures When You Do Work in a Fuel Tank
TASK 28-10-00-910-002-A	Access to the Fuel Tanks and the Work Areas
TASK 28-12-46-000-001-A	Removal of the Overpressure Protector Outlet
TASK 28-25-00-650-001-A	Pressure Defuel
TASK 28-25-00-650-003-A	To Drain Remaining Fuel from the Wing Tanks and the Center Tank
TASK 28-25-00-650-003-A-01	To Drain Remaining Fuel from the Wing Tanks and the Center Tank
TASK 57-27-11-000-002-A	Removal of the Access Panel
Gravity Fill Cap/Adaptor.

3. Job Set-up
Subtask 28-11-43-941-051-A ** ON A/C NOT FOR ALL

A. Safety Precautions

WARNING: BEFORE YOU DO WORK IN OR NEAR A FUEL TANK, MAKE SURE THAT YOU OBEY ALL THE SAFETY PROCEDURES. THIS WILL PREVENT INJURY TO PERSONS AND/OR DAMAGE TO THE AIRCRAFT.

(1) You must obey the fuel safety procedures when you do work in a fuel tank (Ref. AMM TASK 28-10-00-910-001).
(2) Put the SAFETY BARRIER(S) in position.

Subtask 28-11-43-650-050-A ** ON A/C NOT FOR ALL

B. Fuel Configuration
(1) Defuel the applicable fuel tank (Ref. AMM TASK 28-25-00-650-001).
(2) Drain the remaining fuel from the applicable fuel tank (Ref. AMM TASK 28-25-00-650-003).

Subtask 28-11-43-010-050-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE below the applicable access panel 540PB(640PB).
(2) Remove the applicable access panel (Ref. AMM TASK 57-27-11-000-002) and (Ref. AMM TASK 28-10-00-910-002):
(a) FOR [42QM] (ADAPTER-OVERWING REFUEL, L), [44QM] (CAP-OVERWING REFUEL, L)
remove 540PB.
(b) FOR [43QM] (ADAPTER-OVERWING REFUEL, R), [45QM] (CAP-OVERWING REFUEL, R)
remove 640PB.

Subtask 28-11-43-010-050-B ** ON A/C NOT FOR ALL

C. Get Access
(1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE below the applicable access panel 540PB(640PB).
(2) Remove the applicable access panel (Ref. AMM TASK 28-12-46-000-001) and (Ref. AMM TASK 28-10-00-910-002):
(a) FOR [42QM] (ADAPTER-OVERWING REFUEL, L), [44QM] (CAP-OVERWING REFUEL, L)
remove 540PB.
(b) FOR [43QM] (ADAPTER-OVERWING REFUEL, R), [45QM] (CAP-OVERWING REFUEL, R)
remove 640PB.

4. Procedure
Subtask 28-11-43-020-050-A ** ON A/C NOT FOR ALL

A. Removal of the Gravity Fill Cap/Adaptor
(1) Remove the cap (2) from the adaptor (4).
(2) Remove the lanyard (3) from the locking plate (9) and remove the cap (2).
(3) Remove and discard the cotter-pin (12) from the cap (2) and remove the lanyard (3).
(4) Drill out the rivets (8) from the locking plate (9) and the nut (7) and remove the locking plate (9).
(5) Make sure that you remove all the swarf from the work area.
(6) Remove the nut (7) from the adaptor (4) with the 98D28004000000 SPANNER-OVERWING FILLER.
(7) Remove the insulating gasket (10) and the seal ring (11) from the adaptor (4).
(8) Remove the adaptor (4) from the wing.
(9) Remove and discard the O-rings (5) and (6).

[Rev.10 from 2021] 2026.04.02 06:17:06 UTC