Curative Treatment Procedure for Microbiological Contamination - Biobor Method

TASK 28-11-00-600-021-A
Curative Treatment Procedure for Microbiological Contamination - Biobor Method

WARNING: OBEY THE FUEL SAFETY PROCEDURES.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

WARNING: MAKE SURE THE AREA AROUND THE AIRCRAFT IS SAFE BEFORE YOU START THE REFUEL/DEFUEL PROCEDURE. IN THE SAFETY AREA, DO NOT:

SMOKE
MAKE SPARKS OR FIRE
USE ANY EQUIPMENT WHICH IS NOT APPROVED FOR REFUEL/DEFUEL PROCEDURES.

AIRCRAFT FUEL IS FLAMMABLE.

WARNING: BE CAREFUL NOT TO GET AIRCRAFT FUEL IN YOUR MOUTH OR IN YOUR EYES. IF YOU GET FUEL ON YOUR SKIN OR ON YOUR CLOTHES, FLUSH IT IMMEDIATELY WITH WATER. IF NECESSARY, GET MEDICAL HELP. AIRCRAFT FUEL IS POISONOUS.

WARNING: DO NOT SPILL FUEL ON THE ENGINES OR THE BRAKES. IF YOU SPILL FUEL ON ENGINES OR BRAKES THAT ARE HOT, IT CAN CAUSE FIRES.

ZONE: 190
ZONE: 211
ZONE: 500
ZONE: 600

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	METERING EQUIPMENT - BIOCIDE,FLIGHTLINE FUEL ADD.INC.
No specific	AR	SAFETY BARRIER(S)
No specific	AR	WARNING NOTICE(S)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.11KBB1)	Antimicrobial Agent-Fuel System Liquid Additive -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
190	BELLY FAIR, AIR CONDITIONING & HYD COMPT
211	COCKPIT
500	LEFT WING
600	RIGHT WING

D. Referenced Information

REFERENCE	DESIGNATION
TASK 12-11-28-650-004-A	Pressure Refuel with Manual Control
TASK 12-32-28-281-001-A	Drain Water Content
TASK 12-32-28-281-005-A	Operate Water Drain Valves in Installed ACT(S) to Drain Accumulated Water
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 28-00-00-910-001-A	Fuel Safety Procedures
TASK 28-25-00-650-001-A	Pressure Defuel
TASK 31-60-00-860-001-A	EIS Start Procedure
TASK 31-60-00-860-002-A	EIS Stop Procedure
TASK 32-00-00-481-001-A	Installation of the Safety Devices on the Landing Gears
TASK 49-32-41-920-001-A	Replacement of the Fuel Filter (131-9(A))
TASK 49-32-41-920-002-A	Replacement of the Fuel Filter (APS 3200)
TASK 73-11-10-920-001-A	Remove, Inspect and Replace Fuel Filter Element
TASK 73-11-10-920-001-B	Remove, Inspect and Replace Fuel Filter Element
TASK 73-12-42-920-010-A	Remove, Inspect for Contamination and Replace Main Fuel Filter
TASK 73-34-00-040-802-A	Engine Fuel Filter Change
Wing and Center Tanks Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL
Wing and Center Tanks Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL
Wing and Center Tanks Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL
Wing and Center Tanks Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL
Wing and Center Tanks Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL
Wing and Center Tanks Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL
ACT(s) Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL
ACT(s) Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL
Wing and Center Tanks Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL
ACT(s) Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 28-11-00-941-134-A

A. Safety Precautions
(1) Make sure that the required tools and equipment are available to do this procedure.
(2) The procedure that follows is only applicable to Antimicrobial Agent-Fuel System Liquid Additive - (Material No.11KBB1) . The material used is Biobor JF.

NOTE: The use of Biobor JF is subject to local restrictions.

(3) If you use biocide, it is mandatory to use the calibrated METERING EQUIPMENT - BIOCIDE,FLIGHTLINE FUEL ADD.INC. (compliant to EI1566) to mix the biocide into fuel tanks. This is to make sure that the biocide is mixed correctly with the fuel.
(4) If the engines are fed with biocide concentrations more than the limits permitted by the engine manufacturer, there is a high risk of unstable operation of the engines.
(5) No other method of dosing of biocide is permitted by Airbus. If a Metered Injection Rig (EI1566) is not available, you must use the non-biocide process.
(6) Do a check for biocide that was used in last 30 refuellings.
(7) To avoid the interaction of different biocides:
(a) You must use the same biocide that is used in last 30 refuellings (prevents the formation of precipitates).
(b) Airbus recommends to use a separate injection unit for Biobor and Kathon (prevents the risk of crystal formation).
(8) You must obey the fuel safety procedures when you do work on the fuel system (Ref. AMM TASK 28-00-00-910-001).
(9) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
(10) Make sure that the ground safety locks are installed on the landing gear (Ref. AMM TASK 32-00-00-481-001).
(11) Put a WARNING NOTICE(S) in the cockpit to tell persons not to operate:

The aircraft engines
The flap/slat system
The fuel system.

Subtask 28-11-00-860-149-A

B. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Do the EIS start procedure (upper ECAM DU and lower ECAM DU only)
(Ref. AMM TASK 31-60-00-860-001).

4. Procedure
Subtask 28-11-00-680-052-A ** ON A/C NOT FOR ALL

A. Procedure to Drain water from the Tanks
(1) Drain water from all the tanks (Ref. AMM TASK 12-32-28-281-001):
(a) Make sure the fuel sample is clear and bright and there is no water in the sample.
(2) Defuel the aircraft fuel tanks to unpumpable level (Ref. AMM TASK 28-25-00-650-001).

Subtask 28-11-00-600-056-A ** ON A/C NOT FOR ALL

B. Curative Treatment Procedure for Microbiological Contamination - Biobor Method

CAUTION: DO NOT USE BIOBOR BIOCIDE MORE THAN THE SPECIFIED QUANTITY. IF YOU DO, THIS CAN CAUSE: - A DANGEROUS ENGINE MALFUNCTION - SOLIDS IN THE FUEL TANK IF THERE IS WATER IN THE FUEL.

(1) Position the Metered Injection Rig (EI1566) and bond to the aircraft.
(2) Position the bowser/refuel truck and bond to the Metered Injection Rig (EI1566).
(3) Connect the fuel hose from Metered Injection Rig (EI1566) to the aircraft.
(4) Connect the fuel hose from bowser/refuel truck to the Metered Injection Rig (EI1566):
(a) If you use a refuel truck and hydrant system, connect the truck to the hydrant system.

CAUTION: MAKE SURE THAT THE CONCENTRATION OF BIOCIDE IS NOT MORE THAN THE PERMITTED LIMITS. IF THE CONCENTRATION OF BIOCIDE IS MORE THAN THE PERMITTED LIMITS, THERE IS A RISK THAT THE OPERATION OF THE ENGINES WILL NOT BE STABLE.

(5) Make sure that the Metered Injection Rig (EI1566) is calibrated and set to supply 200ml Biobor JF per 1000 liters of fuel:
(a) If necessary, calibrate the Metered Injection Rig (EI1566) and set to the required concentration level. Obey the manufacturers instruction to calibrate the Metered Injection Rig (EI1566).
(6) Airbus recommends only putting in the amount of biocide needed for that particular tank into the injection rig:
(a)

Wing and Center Tanks Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL

(7)

Wing and Center Tanks Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL

(8) Put sufficient supply of biocide in the Metered Injection Rig (EI1566) for that particular tank:
(a) Care must be taken and full chemical resistant PPE worn.
(b) Fill the tank to 100% fill level.

CAUTION: DO NOT DOSE ALL THE FUEL TANKS AT THE SAME TIME. IF YOU DO, THERE IS A RISK THAT THE BIOCIDE CONCENTRATION WILL BE TOO HIGH. THIS CAN CAUSE UNSTABLE ENGINE OPERATION.

(9) Before you proceed further, record the volumes of:

The volume of biocide in the rig
The quantity of fuel in each tank
The bowser/injection rig flow meter/totaliser readings.

(10) Make sure that you apply fuel with Biobor JF at the correct concentration.
(11) Do a manual refuel of each fuel tank (in the sequence shown in the table, refer to step 6) to its maximum capacity with correct concentration of biocide (Ref. AMM TASK 12-11-28-650-004):
(a) This procedure helps to maintain the Center of Gravity (CG) in the permitted limits.
(12) Record fuel and the biocide volumes for each tank before and after each refuel:
(a) You can get the fuel volume from the bowser or the refuel truck. If this is not available, you can calculate the fuel volume as follows:

-------------------------------------

! !

! Vf = Mf !

! ------ !

! Df !

! !

-------------------------------------

Where:

Vf = Volume of fuel (liters)
Mf = Mass of fuel (kg)
Df = Density of fuel (kg/liter) (typically min 0.775kg/liter, but you must use the actual density if this is available).

(b) Do this for each tank in turn before you proceed to the next tank.

CAUTION: MAKE SURE THAT THE CONCENTRATION OF BIOCIDE IS NOT MORE THAN THE PERMITTED LIMITS WITH THE CHECK CALCULATION METHOD. IF THE CONCENTRATION OF BIOCIDE IS MORE THAN THE PERMITTED LIMITS, THERE IS A RISK THAT THE OPERATION OF THE ENGINES WILL NOT BE STABLE.

(13) Do a check calculation for each tank as follows:
(a) Calculate the concentration of biocide as follows:

---------------------------------------

! !

! Cb = 1000*Vb !

! --------- !

! Vf !

! !

---------------------------------------

Where:

Cb = Concentration of biocide (ml/1000 liters)
Vb = Volume of biocide (ml)
Vf = Volume of fuel (liters).

(b) Make sure that the volume of biocide is not more than the value given in the table or the concentration calculated is not more than 200ml/1000 liters for Biobor JF in each tank(s):
1 If this maximum concentration is exceeded, then do not continue but get advice from the Airbus customer-service department.
(14) After all tanks have been refueled, disconnect and remove the fuel hoses, the bowser, the Metered Injection Rig (EI1566) and the bondings.
(15) Install the refuel cap.
(16) Let the biocide dosed fuel stay in the tanks between 36 and 72 hours:

NOTE: Airbus recommends to use the full 72 hours for the best performance.

(a) During the soak time, replace the engine filters and the fuel filter elements, for the replacement of the filter elements go to Para 4.C.
(17) During the soak time:

Do not move the aircraft
Do not operate the fuel pumps or APU
Do not drain water from the fuel tanks (this will contain a high concentration of biocide).

(18) After the soak time, biocide dosed fuel is burned through the APU and the engines during normal operations.
(19) You must burn fuel or defuel in less than 48 hours after the end of the soak time.

Subtask 28-11-00-680-052-B ** ON A/C NOT FOR ALL

C. Procedure to Drain water from the Tanks
(1) Drain water from all the tanks (Ref. AMM TASK 12-32-28-281-001) and (Ref. AMM TASK 12-32-28-281-005):
(a) Make sure the fuel sample is clear and bright and there is no water in the sample.
(2) Defuel the aircraft fuel tanks to unpumpable level (Ref. AMM TASK 28-25-00-650-001).

Subtask 28-11-00-600-056-B ** ON A/C NOT FOR ALL

D. Curative Treatment Procedure for Microbiological Contamination - Biobor Method

CAUTION: DO NOT USE BIOBOR BIOCIDE MORE THAN THE SPECIFIED QUANTITY. IF YOU DO, THIS CAN CAUSE: - A DANGEROUS ENGINE MALFUNCTION - SOLIDS IN THE FUEL TANK IF THERE IS WATER IN THE FUEL.

Wing and Center Tanks Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL

ACT(s) Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL

Wing and Center Tanks Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL

ACT(s) Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL

(7)

Wing and Center Tanks Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL

ACT(s) Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL

Wing and Center Tanks Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL

ACT(s) Fuel Capacity Values - Biobor Process - Curative Treatment ** ON A/C NOT FOR ALL

(8) Put sufficient supply of biocide in the Metered Injection Rig (EI1566) for that particular tank:
(a) Care must be taken and full chemical resistant PPE worn.
(b) Fill the tank to 100% fill level.

CAUTION: DO NOT DOSE ALL THE FUEL TANKS AT THE SAME TIME. IF YOU DO, THERE IS A RISK THAT THE BIOCIDE CONCENTRATION WILL BE TOO HIGH. THIS CAN CAUSE UNSTABLE ENGINE OPERATION.

(9) Before you proceed further, record the volumes of:

The volume of biocide in the rig
The quantity of fuel in each tank
The bowser/injection rig flow meter/totaliser readings.

-----------------------------------------------------------------------

! !

! Vf = Mf !

! ------ !

! Df !

! !

-----------------------------------------------------------------------

Where:

Vf = Volume of fuel (liters)
Mf = Mass of fuel (kg)
Df = Density of fuel (kg/liter) (typically min 0.775kg/liter, but you must use the actual density if this is available).

(b) Do this for each tank in turn before you proceed to the next tank.

(13) Do a check calculation for each tank as follows:
(a) Calculate the concentration of biocide as follows:

------------------------------------------------------------------------

! !

! Cb = 1000*Vb !

! --------- !

! Vf !

! !

------------------------------------------------------------------------

Where:

Cb = Concentration of biocide (ml/1000 liters)
Vb = Volume of biocide (ml)
Vf = Volume of fuel (liters).

(b) Make sure that the volume of biocide is not more than the value given in the table or the concentration calculated is not more than 200ml/1000 liters for Biobor JF in each tank(s):
1 If the maximum concentration is exceeded, then do not continue but get advice from the Airbus customer-service department.
(14) After all tanks have been refueled, disconnect and remove the fuel hoses, the bowser, the Metered Injection Rig (EI1566) and the bondings.
(15) Install the refuel cap.
(16) Let the biocide dosed fuel stay in the tanks between 36 and 72 hours:

NOTE: Airbus recommends to use the full 72 hours for the best performance.

(a) During the soak time, replace the engine filters and the fuel filter elements, for the replacement of the filter elements go to Para 4.C.
(17) During the soak time:

Do not move the aircraft
Do not operate the fuel pumps or APU
Do not drain water from the fuel tanks (this will contain a high concentration of biocide).

Subtask 28-11-00-960-081-A ** ON A/C NOT FOR ALL

E. Replacement of the Fuel Filter Elements
(1) Replace the fuel filter elements for the engine and the APU:

Before the first flight after the biocide treatment and
Between 50 to 75 subsequent flight hours.

(a) Replace the fuel filter elements of engine 1 and 2 (Ref. AMM TASK 73-11-10-920-001).
(b) Replace the APU fuel-filter element:

For 131-9(A) APU (Ref. AMM TASK 49-32-41-920-001)
For APS 3200 APU (Ref. AMM TASK 49-32-41-920-002)
For GTCP 36-300 APU (Ref. AMM D/O 49-32-11-61).

Subtask 28-11-00-960-081-C ** ON A/C NOT FOR ALL

E. Replacement of the Fuel Filter Elements
(1) Replace the fuel filter elements for the engine and the APU:

Before the first flight after the biocide treatment and
Between 50 to 75 subsequent flight hours.

(a) Replace the fuel filter elements of engine 1 and 2 (Ref. AMM TASK 73-34-00-040-802).
(b) Replace the APU fuel-filter element:

For 131-9(A) APU (Ref. AMM TASK 49-32-41-920-001)
For APS 3200 APU (Ref. AMM D/O 49-32-41-92)
For GTCP 36-300 APU (Ref. AMM D/O 49-32-11-61).

Subtask 28-11-00-960-081-E ** ON A/C NOT FOR ALL

E. Replacement of the Fuel Filter Elements
(1) Replace the fuel filter elements for the engine and the APU:

Before the first flight after the biocide treatment and
Between 50 to 75 subsequent flight hours.

(a) Replace the fuel filter elements of engine 1 and 2 (Ref. AMM TASK 73-12-42-920-010).
(b) Replace the APU fuel-filter element:

For 131-9(A) APU (Ref. AMM TASK 49-32-41-920-001)
For APS 3200 APU (Ref. AMM D/O 49-32-41-92)
For GTCP 36-300 APU (Ref. AMM D/O 49-32-11-61).

5. Close-up
Subtask 28-11-00-860-156-A

A. Aircraft Maintenance Configuration
(1) Do the EIS stop procedure
(Ref. AMM TASK 31-60-00-860-002).
(2) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

Subtask 28-11-00-942-137-A

B. Removal of Equipment
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the SAFETY BARRIERS.
(3) Remove the WARNING NOTICE(S).
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.04.02 06:46:27 UTC