Installation of the Control Handle

TASK 27-92-41-400-006-A
Installation of the Control Handle

NOTE: This task is not applicable for the new-generation side-stick unit. For the new-generation side-stick unit, refer to the procedure (Ref. AMM TASK 27-92-41-400-803). To know if the side-stick installed on the aircraft is a new-generation side-stick unit, refer to the procedure (Ref. AMM TASK 27-92-41-860-801).

ZONE: 211
ZONE: 212
FIN: 180VU
FIN: 191VU

1. Reason for the Job
Self Explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.14QDB1)	Wire-Locking Dia: 0.5 mm (0.020 inch) CRES Nickel Alloy -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
211	COCKPIT
212	COCKPIT
822

D. Referenced Information

REFERENCE	DESIGNATION
TASK 23-12-00-710-001-A	Operational Test of the Very High Frequency (VHF) System
TASK 24-42-00-861-001-A	Energize the Ground Service Network from the External Power
TASK 24-42-00-862-001-A	De-energize the Ground Service Network Supplied from the External Power
TASK 27-92-41-400-009-A	Installation of the Side Stick Bellows
TASK 27-92-41-710-001-A	Operational Test of the Side Stick Assembly
TASK 27-96-00-710-003-A	Operational Test of the Side Stick Priority
Control Handle

3. Job Set-up
Subtask 27-92-41-861-055-A

A. Make sure that the ground service network is energized (Ref. AMM TASK 24-42-00-861-001).

Subtask 27-92-41-010-068-A

B. Get Access
(1) Make sure that the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE is in position at the access door 822.
(2) Make sure that the access door 822 is open.
(3) On the battery power center 105VU:

make sure that the protective cover is removed.

Subtask 27-92-41-865-056-A

C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/ELAC1/NORM/SPLY	15CE1	B11
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B08
** ON A/C NOT FOR ALL
49VU	COM/AUDIO/ACP/F/O	5RN	G07
** ON A/C NOT FOR ALL
49VU	COM/AUDIO/ACP/CAPT	4RN	G06
** ON A/C NOT FOR ALL
49VU	COM/ACP F/O/BITE/ INT 2 AUDIO/3&5 OCCPNT	5RN	G07
** ON A/C NOT FOR ALL
49VU	COM/ACP CAPT/SELCAL/INT 1 AUDIO/AVNCS	4RN	G06
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/ELAC1/NORM/SPLY	15CE1	B06
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B03
** ON A/C ALL
105VU	FLIGHT CONTROLS/ELAC2/STBY SPLY	16CE2	A02
105VU	FLT CTL/ELAC1/STBY SPLY	16CE1	A01
105VU	FLT CTL/SEC1/STBY SPLY	22CE	B01
** ON A/C NOT FOR ALL
121VU	AUTO FLT/STICK/LOCK	13CA	N16
** ON A/C ALL
121VU	FLIGHT CONTROLS/SEC3/SPLY	21CE3	Q19
121VU	FLIGHT CONTROLS/SEC2/SPLY	21CE2	Q18
121VU	FLIGHT CONTROLS/ELAC2/NORM/SPLY	15CE2	R20
** ON A/C NOT FOR ALL
121VU	AUTO FLT/STICK/LOCK	13CA	N18

Subtask 27-92-41-869-063-A

D. Make sure that the bellows are removed.

4. Procedure
Subtask 27-92-41-420-055-A

A. Installation of the Control Handle
(1) Clean the component interfaces and the adjacent area.
(2) Do an inspection of the component interfaces and the adjacent area.
(3) Remove the CAP-BLANKING from each electrical connector and receptacle.
(80) and (81).
(4) Make sure that all the electrical connections are clean and in the correct condition.
(5) Connect the handle (75) to the electrical connectors (80). Install the washers (77) and (79) and the screws (76) and (78).
(6) Tighten the screws (76) and (78) and safety them with 14QDB1Wire-Locking Dia: 0.5 mm (0.020 inch) CRES Nickel Alloy -.

Subtask 27-92-41-410-055-A

B. Installation of the Bellows. (Ref. AMM TASK 27-92-41-400-009)

Subtask 27-92-41-210-051-A

C. Check of the Side Stick Movement
(1) Make sure that the side stick :
(a) Is free to move.
(b) Has no friction point along its full range of operation.
(c) Comes correctly to its stops in all the directions.
(d) Goes back to the neutral position when you release it.

Subtask 27-92-41-865-064-A

D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/ELAC1/NORM/SPLY	15CE1	B11
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B08
** ON A/C NOT FOR ALL
49VU	COM/AUDIO/ACP/F/O	5RN	G07
** ON A/C NOT FOR ALL
49VU	COM/AUDIO/ACP/CAPT	4RN	G06
** ON A/C NOT FOR ALL
49VU	COM/ACP F/O/BITE/ INT 2 AUDIO/3&5 OCCPNT	5RN	G07
** ON A/C NOT FOR ALL
49VU	COM/ACP CAPT/SELCAL/INT 1 AUDIO/AVNCS	4RN	G06
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/ELAC1/NORM/SPLY	15CE1	B06
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B03
** ON A/C ALL
105VU	FLIGHT CONTROLS/ELAC2/STBY SPLY	16CE2	A02
105VU	FLT CTL/ELAC1/STBY SPLY	16CE1	A01
105VU	FLT CTL/SEC1/STBY SPLY	22CE	B01
** ON A/C NOT FOR ALL
121VU	AUTO FLT/STICK/LOCK	13CA	N16
** ON A/C ALL
121VU	FLIGHT CONTROLS/SEC3/SPLY	21CE3	Q19
121VU	FLIGHT CONTROLS/SEC2/SPLY	21CE2	Q18
121VU	FLIGHT CONTROLS/ELAC2/NORM/SPLY	15CE2	R20
** ON A/C NOT FOR ALL
121VU	AUTO FLT/STICK/LOCK	13CA	N18

Subtask 27-92-41-710-051-A

E. Operational Test
(1) Do the operational test of the Side Stick Assembly (Ref. AMM TASK 27-92-41-710-001).
(2) Do the operational test of the AP disconnect/priority pushbutton switch (Ref. AMM TASK 27-96-00-710-003).
(3) Do the operational test of the radio PTT switch (Ref. AMM TASK 23-12-00-710-001).

5. Close-up
Subtask 27-92-41-942-051-A

A. Make sure that the work area is clean and clear of tools and other items.

Subtask 27-92-41-862-053-A

B. De-energize the ground service network
(Ref. AMM TASK 24-42-00-862-001).

Subtask 27-92-41-410-066-A

C. Close Access
(1) Install the protective cover on the battery power center 105VU.
(2) Tighten the two screws.
(3) Close the access door 822.
(4) Remove the access platform(s).

[Rev.10 from 2021] 2026.03.31 23:58:55 UTC