W DOC AIRBUS | AMM A320F

Installation of the Side Stick Assembly

TASK 27-92-41-400-001-A
Installation of the Side Stick Assembly

WARNING: MAKE SURE THAT THE SIDE STICK ASSEMBLY STAYS IN THE VERTICAL POSITION DURING THE MAINTENANCE PROCEDURES. IF NOT THERE IS A RISK OF SKYDROL LEAKAGE. SKYDROL CAN CAUSE INJURY AND/OR DAMAGE.
NOTE: This task is not applicable for the new-generation side-stick unit. For the new-generation side-stick unit, refer to the procedure (Ref. AMM TASK 27-92-41-400-802). To know if the side-stick installed on the aircraft is a new-generation side-stick unit, refer to the procedure (Ref. AMM TASK 27-92-41-860-801).
ZONE: 211
ZONE: 212
1. Reason for the Job
Self explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
1
ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific
AR
WARNING NOTICE(S)
No specific
Torque wrench: range to between 0.42 and 0.38 m.daN (37.17 and 33.63 lbf.in ) T
98D27303001001
1
HOLDER - SIDE STICK
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
211
COCKPIT
212
COCKPIT
822
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 24-42-00-861-001-A
Energize the Ground Service Network from the External Power
TASK 24-42-00-862-001-A
De-energize the Ground Service Network Supplied from the External Power
TASK 27-92-41-710-001-A
Operational Test of the Side Stick Assembly
TASK 31-61-14-400-801-A
Installation of the Cursor Control Device (CCD)
F Side Stick Clips Location.
F Side Stick Assembly
F Cover Panel ** ON A/C NOT FOR ALL
F Cover Panel ** ON A/C NOT FOR ALL
3. Job Set-up
Subtask 27-92-41-861-053-A
A. Make sure that the ground service network is energized (Ref. AMM TASK 24-42-00-861-001).
Subtask 27-92-41-010-066-A
B. Get Access
   (1) Make sure that the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE is in position at the access door 822.
   (2) Make sure that the access door 822 is open.
   (3) On the battery power center 105VU:
  • make sure that the protective cover is removed.
Subtask 27-92-41-865-054-A
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/ELAC1/NORM/SPLY15CE1B11
49VUFLIGHT CONTROLS/SEC1/NORM/SPLY21CE1B08
** ON A/C NOT FOR ALL
49VUCOM/AUDIO/ACP/F/O5RNG07
** ON A/C NOT FOR ALL
49VUCOM/AUDIO/ACP/CAPT4RNG06
** ON A/C NOT FOR ALL
49VUCOM/ACP F/O/BITE/ INT 2 AUDIO/3&5 OCCPNT5RNG07
** ON A/C NOT FOR ALL
49VUCOM/ACP CAPT/SELCAL/INT 1 AUDIO/AVNCS4RNG06
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/ELAC1/NORM/SPLY15CE1B06
49VUFLIGHT CONTROLS/SEC1/NORM/SPLY21CE1B03
** ON A/C ALL
105VUFLIGHT CONTROLS/ELAC2/STBY SPLY16CE2A02
105VUFLT CTL/ELAC1/STBY SPLY16CE1A01
105VUFLT CTL/SEC1/STBY SPLY22CEB01
** ON A/C NOT FOR ALL
121VUAUTO FLT/STICK/LOCK13CAN16
** ON A/C ALL
121VUFLIGHT CONTROLS/SEC3/SPLY21CE3Q19
121VUFLIGHT CONTROLS/SEC2/SPLY21CE2Q18
121VUFLIGHT CONTROLS/ELAC2/NORM/SPLY15CE2R20
** ON A/C NOT FOR ALL
121VUAUTO FLT/STICK/LOCK13CAN18
Subtask 27-92-41-860-050-A
D. Aircraft Maintenance Configuration
F Side Stick Clips Location.
CAUTION: MAKE SURE THAT THE CLIPS ARE IN POSITION AND CORRECTLY INSTALLED ON THE SIDE STICK ASSEMBLY.
   (1) Make sure that the cover panel is removed.
   (2) Make sure that the side stick assembly is installed on the 98D27303001001 HOLDER - SIDE STICK
   (3) Make sure that the 98D27903500000 PIN-SIDE STICK LOCKING is installed
   (4) Make sure that the WARNING NOTICE(S) which tells persons not to operate the side stick is in position on the side stick.
4. Procedure
Subtask 27-92-41-410-060-A
CAUTION: MAKE SURE THAT THE CLIPS ARE IN POSITION AND CORRECTLY INSTALLED ON THE SIDE STICK ASSEMBLY.
A. Installation of the Casing (if removed)
F Side Stick Clips Location.
   (1) Install the casing assembly (27) and (30) on the side stick assembly (12).
   (2) Install the washers (29), the screws (28) and tighten.
Subtask 27-92-41-420-050-A
B. Installation of the Side Stick Assembly
   (1) Clean the component interfaces and the adjacent area.
   (2) Do an inspection of the component interfaces and the adjacent area.
   (3) Remove the CAP-BLANKING from each electrical connector and receptacle.
(16), (17), (18), (19), (20) and (21).
   (4) Make sure that the electrical connectors are clean and in the correct condition.
   (5) Connect the electrical connectors (13), (14), (15), (22), (23) and (24).
WARNING: BE CAREFUL NOT TO CAUSE DAMAGE TO THE LOWER PART OF THE SIDE STICK (MECHANISM) WHEN YOU INSTALL IT ON ITS SUPPORT.
   (6) Put the side stick assembly (11) in position on its support (12).
   (7) Install the washers (25) and the screws (26).
   (8) TORQUE the screws (26) to between 0.42 and 0.38 m.daN (37.17 and 33.63 lbf.in ) T.
Subtask 27-92-41-080-050-A
C. Remove the 98D27903500000 PIN-SIDE STICK LOCKING (10) and the warning notice from the side stick.
Subtask 27-92-41-410-050-A ** ON A/C NOT FOR ALL
D. Installation of the Cover panel.
F Cover Panel ** ON A/C NOT FOR ALL
   (1) Clean the component interfaces and the adjacent area.
   (2) Do an inspection of the component interfaces and the adjacent area.
   (3) Put the cover (3) in position.
   (4) Install the washers (5), washer (7), screws (4), screw (8) and screw (6).
   (5) Tighten the screws (4), screw (8) and screw (6).
   (6) Lock the fasteners (2).
   (7) Release the lock (9) and install the handle (1).
Subtask 27-92-41-410-050-B ** ON A/C NOT FOR ALL
D. Installation of the Cover panel.
F Cover Panel ** ON A/C NOT FOR ALL
   (1) Clean the component interfaces and the adjacent area.
   (2) Do an inspection of the component interfaces and the adjacent area.
   (3) Put the cover (3) in position.
   (4) Install the fasteners (2) and tighten them.
   (5) Install the washers (5), washer (7), screws (4), screw (8) and screw (6).
   (6) Tighten the screws (4), screw (8) and screw (6).
   (7) Install the handle (1) and the screws (9).
   (8) Tighten the screws (9).
Subtask 27-92-41-410-078-A ** ON A/C NOT FOR ALL
E. Install the Cursor Control Device (CCD) (Ref. AMM TASK 31-61-14-400-801).
Subtask 27-92-41-210-050-A
F. Check of the Side Stick Movement
   (1) Make sure that the side stick:
     (a) Is free to move.
     (b) Has no friction point along its full range of operation.
     (c) Goes correctly to its stops in all the directions.
     (d) Goes back to the neutral position when you release it.
Subtask 27-92-41-865-063-A
G. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/ELAC1/NORM/SPLY15CE1B11
49VUFLIGHT CONTROLS/SEC1/NORM/SPLY21CE1B08
** ON A/C NOT FOR ALL
49VUCOM/AUDIO/ACP/F/O5RNG07
** ON A/C NOT FOR ALL
49VUCOM/AUDIO/ACP/CAPT4RNG06
** ON A/C NOT FOR ALL
49VUCOM/ACP F/O/BITE/ INT 2 AUDIO/3&5 OCCPNT5RNG07
** ON A/C NOT FOR ALL
49VUCOM/ACP CAPT/SELCAL/INT 1 AUDIO/AVNCS4RNG06
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/ELAC1/NORM/SPLY15CE1B06
49VUFLIGHT CONTROLS/SEC1/NORM/SPLY21CE1B03
** ON A/C ALL
105VUFLIGHT CONTROLS/ELAC2/STBY SPLY16CE2A02
105VUFLT CTL/ELAC1/STBY SPLY16CE1A01
105VUFLT CTL/SEC1/STBY SPLY22CEB01
** ON A/C NOT FOR ALL
121VUAUTO FLT/STICK/LOCK13CAN16
** ON A/C ALL
121VUFLIGHT CONTROLS/SEC3/SPLY21CE3Q19
121VUFLIGHT CONTROLS/SEC2/SPLY21CE2Q18
121VUFLIGHT CONTROLS/ELAC2/NORM/SPLY15CE2R20
** ON A/C NOT FOR ALL
121VUAUTO FLT/STICK/LOCK13CAN18
Subtask 27-92-41-710-050-A
H. Test
   (1) Do the operational test of the side stick assembly (Ref. AMM TASK 27-92-41-710-001).
5. Close-up
Subtask 27-92-41-942-050-A
A. Make sure that the work area is clean and clear of tools and other items.
Subtask 27-92-41-862-052-A
B. De-energize the ground service network
(Ref. AMM TASK 24-42-00-862-001).
Subtask 27-92-41-410-065-A
C. Close Access
   (1) Install the protective cover on the battery power center 105VU.
   (2) Tighten the two screws.
   (3) Close the access door 822.
   (4) Remove the access platform(s).
[Rev.10 from 2021] 2026.03.31 23:58:52 UTC
"Aviabrain" 2025