Removal of the Control-Handle of the New-Generation Side Stick Unit (SSU)

TASK 27-92-41-000-803-A
Removal of the Control-Handle of the New-Generation Side Stick Unit (SSU)

NOTE: This task is applicable only for the new-generation side-stick unit. For the other side-stick assemblies, refer to the procedure (Ref. AMM TASK 27-92-41-000-006). To know if the side-stick installed on the aircraft is a new-generation side-stick unit refer to the procedure (Ref. AMM TASK 27-92-41-860-801).

ZONE: 211
ZONE: 212

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific	AR	CAP - BLANKING
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
211	COCKPIT
212	COCKPIT
822

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-42-00-861-001-A	Energize the Ground Service Network from the External Power
TASK 29-00-00-864-001-A	Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action
New-Generation Side-Stick Unit - Control-Handle

3. Job Set-up
Subtask 27-92-41-861-060-A

A. Aircraft Maintenance Configuration
(1) Energize the ground service network
(Ref. AMM TASK 24-42-00-861-001).
(2) Make sure that the aircraft hydraulic systems are depressurized (Ref. AMM TASK 29-00-00-864-001).

Subtask 27-92-41-010-076-A

B. Get Access
(1) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position at the access door 822.
(2) Open the access door 822.
(3) On the battery power center 105VU:

Loosen the two screws and remove the protective cover.

Subtask 27-92-41-865-068-A

C. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/ELAC1/NORM/SPLY	15CE1	B11
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B08
** ON A/C NOT FOR ALL
49VU	COM/AUDIO/ACP/F/O	5RN	G07
** ON A/C NOT FOR ALL
49VU	COM/AUDIO/ACP/CAPT	4RN	G06
** ON A/C NOT FOR ALL
49VU	COM/ACP F/O/BITE/ INT 2 AUDIO/3&5 OCCPNT	5RN	G07
** ON A/C NOT FOR ALL
49VU	COM/ACP CAPT/SELCAL/INT 1 AUDIO/AVNCS	4RN	G06
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/ELAC1/NORM/SPLY	15CE1	B06
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B03
** ON A/C ALL
105VU	FLIGHT CONTROLS/ELAC2/STBY SPLY	16CE2	A02
105VU	FLT CTL/ELAC1/STBY SPLY	16CE1	A01
105VU	FLT CTL/SEC1/STBY SPLY	22CE	B01
** ON A/C NOT FOR ALL
121VU	AUTO FLT/STICK/LOCK	13CA	N16
** ON A/C ALL
121VU	FLIGHT CONTROLS/SEC3/SPLY	21CE3	Q19
121VU	FLIGHT CONTROLS/SEC2/SPLY	21CE2	Q18
121VU	FLIGHT CONTROLS/ELAC2/NORM/SPLY	15CE2	R20
** ON A/C NOT FOR ALL
121VU	AUTO FLT/STICK/LOCK	13CA	N18

4. Procedure
Subtask 27-92-41-020-063-A

A. Removal of the Control-Handle of the New-Generation Side-Stick Unit
(1) Remove and discard the collar-clamp (2) that attaches the bellows (3) to the control handle (1).
(2) Lower the top part of the bellows (3) to get access to the captive screws (5) and (6).
(3) Unfold the locktabs (4) and release the captive screws (5) and (6).
(4) Disconnect the control handle (1) and remove it.
(5) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(6) Put a protection in position to make sure that no unwanted materials can go into the bellows opening.

[Rev.10 from 2021] 2026.03.31 23:58:56 UTC