W DOC AIRBUS | AMM A320F

Removal of the Speedbrake Control Transducer-Unit

TASK 27-92-14-000-001-A
Removal of the Speedbrake Control Transducer-Unit

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND THE RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
CAUTION: TO PREVENT POSSIBLE CROSS-CONNECTION OF THE ELECTRICAL CONNECTORS, MAKE SURE THAT PLUGS AND RECEPTACLES ARE CLEARLY IDENTIFIED.
ZONE: 210
FIN: 7CE
1. Reason for the Job
Self Explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
1
ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific
AR
CAP - BLANKING
No specific
AR
SAFETY CLIP - CIRCUIT BREAKER
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
210
CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD
822
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 29-10-00-864-003-A
Depressurize the Blue Hydraulic System
TASK 29-23-00-864-001-A
Depressurize the Green and Yellow Hydraulic Systems after Operation of the PTU
TASK 29-24-00-864-001-A
Depressurize the Yellow Hydraulic System
F Speedbrake Control Transducer-Unit
3. Job Set-up
Subtask 27-92-14-860-050-A
A. Aircraft Maintenance Configuration
   (1) Make sure that the SPEED BRAKE control lever is in the RET position.
   (2) Make sure that the hydraulic systems are depressurized
(Ref. AMM TASK 29-23-00-864-001) (Ref. AMM TASK 29-24-00-864-001) (Ref. AMM TASK 29-10-00-864-003).
Subtask 27-92-14-010-050-A
B. Get Access
   (1) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position below access door 822.
   (2) Open access door 822.
   (3) On battery power center 105VU:
  • Loosen the two screws and remove the protective cover.
Subtask 27-92-14-865-050-A
C. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/SEC1/NORM/SPLY21CE1B08
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/SEC1/NORM/SPLY21CE1B03
** ON A/C ALL
105VUFLT CTL/SEC1/STBY SPLY22CEB01
121VUFLIGHT CONTROLS/SEC3/SPLY21CE3Q19
121VUFLIGHT CONTROLS/SEC2/SPLY21CE2Q18
122VULIGHTING/INSTL LT/MAIN INST/PNL AND/PED4LFY04
4. Procedure
Subtask 27-92-14-020-050-A
A. Removal of the Speedbrake Control Transducer-Unit
   (1) Remove the screws (1) and the washers (2).
   (2) Lift the transducer unit (3).
   (3) Disconnect the connectors (4), (5), (6) and (7).
   (4) Remove the transducer unit (3).
   (5) Put CAP - BLANKING on the connectors (4), (5), (6) and (7), and on the connectors of the transducer unit (3).
[Rev.10 from 2021] 2026.03.31 23:58:31 UTC
"Aviabrain" 2025