Extending the Slats on the Ground

TASK 27-80-00-866-004-A
Extending the Slats on the Ground

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

1. Reason for the Job
To extend the slats without movement of the flaps. To extend the slats and flaps at the same time (Ref. TASK 27-50-00-866-008-A01).
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	SAFETY BARRIER(S)
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)
98D27803000000	1	LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION

B. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 27-00-00-480-002-A	Installation of the Flap/Slat Control-Lever Locking Tool (98D27803000000)
TASK 29-10-00-863-003-A	Pressurize the Blue Hydraulic System with a Hydraulic Ground Power-Cart
TASK 29-10-00-863-003-A-01	Pressurize the Blue Hydraulic System with the Blue Electric Pump
TASK 29-10-00-864-003-A	Depressurize the Blue Hydraulic System
TASK 31-60-00-860-001-A	EIS Start Procedure

3. Job Set-up
Subtask 27-80-00-941-052-A

A. Safety Precautions
(1) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
(2) Put the WARNING NOTICE(S) in position to tell persons that the slat system is in operation.

Subtask 27-80-00-860-052-A

B. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-861-002).
(2) Pressurize the Blue hydraulic system
(Ref. AMM TASK 29-10-00-863-003).

NOTE: The Blue and/or Green hydraulic system(s) operate(s) the slat system. If necessary, use the alternative hydraulic system.

NOTE: If you use the Blue Hydraulic System, an ECAM S/CTL SLAT SYS 2 FAULT message will show. This message can be ignored.

NOTE: If you use the Green Hydraulic System, an ECAM S/CTL SLAT SYS 1 FAULT message will show. This message can be ignored.

(3) Set the ECAM system to on (Ref. AMM TASK 31-60-00-860-001).

Subtask 27-80-00-865-054-A

C. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B07
49VU	AUTO FLT/FAC1/26VAC	14CC1	B03
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B02
49VU	AUTO FLT/FAC1/26VAC	14CC1	H09
** ON A/C ALL
121VU	AUTO FLT/FAC2/26VAC	14CC2	M18
121VU	FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2	8CV	Q21

Subtask 27-80-00-865-055-A

D. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1	5CV	B06
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1	5CV	B01
** ON A/C ALL
121VU	FLIGHT CONTROLS/WTB/SLT/SYS2	11CV	P19
121VU	FLIGHT CONTROLS/SLT/CTL/SYS2	7CV	R21
122VU	FLIGHT CONTROLS/WTB/SLT/SYS1	9CV	S06

4. Procedure
Subtask 27-80-00-866-052-A ** ON A/C NOT FOR ALL

A. Extension of the Slats on the Ground

WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

CAUTION: IF THE THRUST REVERSER COWLS ARE OPEN, MAKE SURE THAT THE HALF DOORS OF THE THRUST REVERSER ARE CLOSED BEFORE YOU EXTEND THE SLATS. IF THE DOORS ARE OPEN, YOU CAN CAUSE DAMAGE TO THE SLATS AND HALF DOORS WHEN THE SLATS EXTEND.

(1) Set the slat/flap control lever to position 1, 2 or FULL.
(2) Make sure that on the ECAM upper DU the slat position bar moves to the correct position.
(3) Install the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION on the slat/flap control lever (Ref. AMM TASK 27-00-00-480-002).

Subtask 27-80-00-866-052-B ** ON A/C NOT FOR ALL

A. Extension of the Slats on the Ground

WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

Subtask 27-80-00-866-052-C ** ON A/C NOT FOR ALL

A. Extension of the Slats on the Ground

WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

CAUTION: DO NOT EXTEND THE SLATS WHEN THE FAN COWLS AND THE THRUST REVERSER COWLS ARE OPEN. IF YOU DO THIS, DAMAGE TO THE AIRCRAFT CAN OCCUR.

5. Close-up
Subtask 27-80-00-860-053-A

A. Aircraft Maintenance Configuration
(1) Depressurize the Blue hydraulic system
(Ref. AMM TASK 29-10-00-864-003).
(2) On the ECAM control panel, set the control/brightness controls to OFF.
(3) De-energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-862-002).

Subtask 27-80-00-942-057-A

B. Removal of Equipment
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the safety barriers.
(3) Remove the WARNING NOTICE(S).
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.04.01 03:52:57 UTC