Removal of the Filter

TASK 27-64-51-000-003-A
Removal of the Filter

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

WARNING: YOU MUST PUT ON AND ATTACH A SAFETY HARNESS BEFORE YOU START WORK:

ON THE THS OR IN THE REAR FUSELAGE
ON TOP OF THE WINGS OR PYLONS.

WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU OR CAUSE YOU INJURY.

CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:

DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.

ZONE: 500
ZONE: 600

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE
No specific	AR	PLUG - BLANKING
No specific	AR	SAFETY BARRIER(S)
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)
98D27604000000	1	COLLAR-SAFETY, SPOILER
98D27604004000	1	COLLAR SAFETY SPOILER
98D27803000000	1	LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION
98L12003001000	1	HARNESS,SAFETY

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
500	LEFT WING
600	RIGHT WING

C. Referenced Information

REFERENCE	DESIGNATION
TASK 27-50-00-866-008-A	Extension of the Flaps on the Ground
TASK 27-50-00-866-008-A-01	Extension of the Flaps/Slats on the Ground
TASK 27-60-00-866-002-A	Extension-Retraction of the Spoilers for Maintenance
TASK 29-10-00-864-001-A	Depressurize the Green Hydraulic System
TASK 29-10-00-864-002-A	Depressurize the Yellow Hydraulic System
TASK 29-10-00-864-003-A	Depressurize the Blue Hydraulic System
TASK 29-14-00-614-001-A	Depressurization of the Hydraulic Reservoirs
Filter Assembly - Location and Detail

3. Job Set-up
Subtask 27-64-51-941-062-A

A. Safety Precautions
(1) Put the SAFETY BARRIER(S) in position.
(2) Put the WARNING NOTICE(S) in the cockpit to tell persons not to operate the slat controls.
(3) Put the WARNING NOTICE(S) in the cockpit to tell persons not to pressurize the hydraulics.

Subtask 27-64-51-875-059-A

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B08
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B07
** ON A/C ALL
49VU	HYD/HYD PWR/B WARN/& CTL	2702GJ	C12
** ON A/C NOT FOR ALL
49VU	HYDRAULIC/G HYD/PUMP ENG1/CTL	1701GK	H12
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B03
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B02
** ON A/C ALL
105VU	FLT CTL/SEC1/STBY SPLY	22CE	B01
** ON A/C NOT FOR ALL
121VU	HYDRAULIC/G HYD/PUMP ENG1/CTL	1701GK	R35
** ON A/C NOT FOR ALL
121VU	HYDRAULIC/HYD POWER/Y	3803GX	N30
121VU	HYDRAULIC/G HYD/PUMP ENG1/MONG	1702GK	R34
** ON A/C ALL
121VU	HYDRAULIC/SOL VALVES/G/Y/PTU	1801GL	N34
121VU	HYDRAULIC/Y HYD/PUMP ENG2/MONG	3700GD	Q37
121VU	HYDRAULIC/Y HYD/PUMP ENG2/CTL	3701GD	Q36
121VU	FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2	8CV	Q21
121VU	FLIGHT CONTROLS/SEC3/SPLY	21CE3	Q19
121VU	FLIGHT CONTROLS/SEC2/SPLY	21CE2	Q18
** ON A/C NOT FOR ALL
121VU	HYDRAULIC/HYD POWER/Y	3803GX	N31
121VU	HYDRAULIC/G HYD/PUMP ENG1/MONG	1702GK	R33
** ON A/C ALL
123VU	B HYD/ELEC PUMP	2701GJ	AB09
123VU	Y HYD/ELEC/PUMP	3802GX	AB06
123VU	Y HYD/ELEC/ELEC PUMP/NORM	3801GX	AB03

Subtask 27-64-51-865-056-A

DELETED

Subtask 27-64-51-860-060-B

D. Aircraft Maintenance Configuration
(1) Extend the applicable spoiler (Ref. AMM TASK 27-60-00-866-002).
(2) Make sure that the 98D27604000000 COLLAR-SAFETY, SPOILER or 98D27604004000 COLLAR SAFETY SPOILER is on the piston rod of the servo-control.
(3) Extend the flaps fully (Ref. AMM TASK 27-50-00-866-008).
(4) Make sure that the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION is installed.
(5) Depressurize the applicable hydraulic system:

For the spoiler 1 and the spoiler 5, depressurize the Green hydraulic system (Ref. AMM TASK 29-10-00-864-001)
For the spoiler 2 and the spoiler 4, depressurize the Yellow hydraulic system (Ref. AMM TASK 29-10-00-864-002)
For the spoiler 3, depressurize the Blue hydraulic system (Ref. AMM TASK 29-10-00-864-003).

(6) Depressurize the applicable reservoirs (Ref. AMM TASK 29-14-00-614-001).
(7) Put on a safety harness:

WARNING: BEFORE YOU START WORK, YOU MUST PUT ON A SAFETY HARNESS AND ATTACH IT TO THE ACCESS PLATFORM. WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU OR CAUSE YOU INJURY.

(a) Put on and attach a 98L12003001000 HARNESS,SAFETY before you start work in the work area.

Subtask 27-64-51-010-055-A

E. Get Access
(1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position below the applicable spoiler servo control.

4. Procedure

CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:

DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.

Subtask 27-64-51-020-052-A

A. Removal of the Filter

WARNING: USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

(1) Cut, remove and discard the lockwire from the filter (2).
(2) Remove the filter (2) from the spoiler servo control.
(3) Remove and discard the O-ring (1) from the filter (2).
(4) Install a PLUG - BLANKING on the spoiler servo control.

[Rev.10 from 2021] 2026.03.31 23:56:02 UTC