Installation of the Torque Shaft

TASK 27-54-45-400-010-A
Installation of the Torque Shaft

WARNING: MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING NOTICES ARE IN POSITION.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:

DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.

FIN: 6222CM
FIN: 6272CM

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE
No specific	AR	SAFETY BARRIER(S)
No specific	AR	WARNING NOTICE(S)
No specific	Torque wrench: range to between 1.24 and 1.02 m.daN (109.73 and 90.27 lbf.in )

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.03FDB1)	Mineral Oil base Grease-Anti-Fretting Paste -
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.12ACC1)	Corrosion Preventive Compound-Heavy Duty Soft Film -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [6222CM] (FLAP XMSN TORQUE SHAFT)
575CB
FOR [6272CM] (FLAP XMSN TORQUE SHAFT)
675CB

D. Expendable Parts

FIG.ITEM	DESIGNATION	IPC-CSN
80	NUTS	AIPC 27-54-45-11-010

E. Referenced Information

REFERENCE	DESIGNATION
TASK 27-50-00-000-003-A	Removal of the Lock-Torque Shaft - Flaps and Slats (98D27504030001)
TASK 27-50-00-400-003-A	Installation of the Lock-Torque Shaft - Flaps and Slats (98D27504030001)
TASK 27-50-00-866-008-A	Extension of the Flaps on the Ground
TASK 27-50-00-866-008-A-01	Extension of the Flaps/Slats on the Ground
TASK 27-50-00-866-009-A	Retraction of the Flaps on the Ground
TASK 27-50-00-866-009-A-01	Retraction of the Flaps/Slats on the Ground
TASK 27-54-00-710-001-A	Operational Test of the Flap System
TASK 27-60-00-866-002-A	Extension-Retraction of the Spoilers for Maintenance
TASK 57-51-37-000-004-A	Removal of the Access Panels 575AB(675AB), 575BB(675BB), 575CB(675CB), 575DB(675DB), 575EB(675EB), 575FB(675FB), 575GB(675GB), 575HB(675HB)
TASK 57-51-37-400-004-A	Installation of the Access Panels 575AB(675AB), 575BB(675BB), 575CB(675CB), 575DB(675DB), 575EB(675EB), 575FB(675FB), 575GB(675GB), 575HB(675HB)
Torque Shafts - Flap Power Transmission ** ON A/C NOT FOR ALL
Torque Shafts - Flap Power Transmission ** ON A/C NOT FOR ALL
Torque Shafts- Flap Power Transmission

3. Job Set-up
Subtask 27-54-45-941-086-A

A. Safety Precautions
(1) Make sure that the SAFETY BARRIER(S) are in position.
(2) Make sure that the WARNING NOTICE(S) is in position to tell persons not to operate the flap/slat controls.

Subtask 27-54-45-860-072-A

B. Aircraft Maintenance Configuration

WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

(1) Make sure that the flaps are fully extended (Ref. AMM TASK 27-50-00-866-008).
(2) Make sure that the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION is on the flap/slat control lever on panel 114VU.
(3) Make sure that the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE is in the applicable position.
(4) Make sure that the applicable spoiler is in the 'M' (Maintenance) position (Ref. AMM TASK 27-60-00-866-002).
(5) Make sure that the 98D27604000000 COLLAR-SAFETY, SPOILER or 98D27604004000 COLLAR SAFETY SPOILER is on the piston rod of the servo-control.
(6) Make sure that the applicable access panel is removed (Ref. AMM TASK 57-51-37-000-004):

for 6222CM, panel 575CB
for 6272CM, panel 675CB.

(7) Make sure that the 98D27504030001 LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT is installed on the flap torque shaft (Ref. AMM TASK 27-50-00-400-003), outboard of the removed component.

Subtask 27-54-45-865-087-A

C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B07
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B02
** ON A/C ALL
121VU	FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2	8CV	Q21

4. Procedure

CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:

DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.

Subtask 27-54-45-420-072-A

A. Preparation for Installation
(1) Clean the parts:
(a) Use a clean Textile-Lint free Cotton - (Material No.14SBA1) made moist with Non Aqueous Cleaner-General - - (Material No.08BAA9) to clean the:

New AIPC 27-54-45-11-010 NUTS (80)
Bolts (81)
Flanges of the torque shaft (78) and the torsion shaft (79).

(2) Dry the parts:

WARNING: WHEN YOU USE COMPRESSED AIR:

USE THE CORRECT PROTECTION (FACE SHIELD OR GOGGLES)
DO NOT POINT THE AIRFLOW AT YOURSELF OR OTHER PERSONS.

LOOSE PARTICLES AND/OR HIGH PRESSURE AIR CAN CAUSE INJURY.

WARNING: DO NOT LET COMPRESSED GAS TOUCH YOUR SKIN. THE GAS CAN GO THROUGH THE SKIN AND MAKE BUBBLES IN THE BLOOD. THIS CONDITION CAN KILL YOU.

(a) Use compressed air to dry the cleaned areas.
(3) Make sure that the parts retained from the removed component are clean and in the correct condition.
(4) Do an inspection of the component interfaces and the adjacent area.
(5) Apply a thin layer of Mineral Oil base Grease-Anti-Fretting Paste - (Material No.03FDB1) to the torque shaft splines.

Subtask 27-54-45-420-059-A

B. Installation of the Torque Shaft
(1) Install the torsion shaft (79) and align its flange with the flange of the steady bearing.
(2) Install the torque shaft (78) and attach it with the bolts (81) and the nuts (80).
(3) TORQUE the nuts (80) to between 1.24 and 1.02 m.daN (109.73 and 90.27 lbf.in )

.
(4) Make sure that:

you cannot see the spline engagement groove at the movable joint
the dimension A is a minimum of 6.5 mm (0.2559 in.) at the movable joint.

(5) Remove the 98D27504030001 LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT (Ref. AMM TASK 27-50-00-000-003).

Subtask 27-54-45-916-058-A

C. Application of Special Materials
(1) Apply a layer of Corrosion Preventive Compound-Heavy Duty Soft Film - (Material No.12ACC1) to the:

nuts (80)
bolts (81)
flanges of the torque shaft (78) and the torsion shaft (79).

Subtask 27-54-45-865-088-A

D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B07
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B02
** ON A/C ALL
121VU	FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2	8CV	Q21

Subtask 27-54-45-710-059-A

E. Operational Test of the Flap System
(1) Remove the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION from the flap/slat control lever.
(2) Retract the flaps fully (Ref. AMM TASK 27-50-00-866-009).
(3) Do an operational test of the flap system (Ref. AMM TASK 27-54-00-710-001). Make sure that the operation of the torque shafts is satisfactory.

5. Close-up
Subtask 27-54-45-410-058-A

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the 98D27604000000 COLLAR-SAFETY, SPOILER or 98D27604004000 COLLAR SAFETY SPOILER from the piston rod of the servo-control.
(3) Put the applicable spoiler back to the 'O' (Operation) position (Ref. AMM TASK 27-60-00-866-002).
(4) On the servo-control, make sure that the pointer on the hex-head is opposite the letter 'O' (Operation) on the housing.
(5) Install the applicable access panel (Ref. AMM TASK 57-51-37-400-004):
(a) FOR [6222CM] (FLAP XMSN TORQUE SHAFT)
install 575CB
(b) FOR [6272CM] (FLAP XMSN TORQUE SHAFT)
install 675CB.

Subtask 27-54-45-942-059-A

B. Removal of Equipment
(1) Remove the safety barriers.
(2) Remove the WARNING NOTICE(S).
(3) Remove the access platform(s).
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.03.31 23:53:38 UTC