Adjustment (Rigging) of the Flaps with the Sharks Fin Tool (A318/319/320)

TASK 27-51-00-820-008-A
Adjustment (Rigging) of the Flaps with the Sharks Fin Tool (A318/319/320)

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

NOTE: If the label with the asymmetric offset value on the track 3 is missing or nonreadable, refer to SB 27-1034 or ISI 27.54.00002.

1. Reason for the Job
Flap rigging is done:

when specified in an AMM Task
when specified in a TSM Task
if you think the flap rigged position is incorrect.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 3M (10 FT)
No specific	AR	SAFETY BARRIER(S)
No specific	AR	WARNING NOTICE(S)
No specific	Torque wrench: range to between 0.12 and 0.05 m.daN (10.62 and 4.42 lbf.in )
No specific	Torque wrench: range to between 1.5 and 1.0 m.daN (132.74 and 88.50 lbf.in )
No specific	Torque wrench: range to between 2.8 and 2.6 m.daN (20.65 and 19.17 lbf.ft )
No specific	Torque wrench: range to between 7.0 and 5.4 m.daN (51.62 and 39.82 lbf.ft )
No specific	Torque wrench: range to between 20 and 15 m.daN (147.49 and 110.62 lbf.ft )
98D27504002000	1	FLAP ADJUSTING TOOL
98D27504005000	1	PIN RIGGING-FLAPS (TRACK 1)
98D27504006000	3	PIN-RIGGING, FLAPS
98D27504035000	1	TORQUE ADAPTER-TRUNNION NUT
98D27504038001	1	KIT-FLAP RIGGING
98D27504039000	2	TOOL-RESTRAINING,TK1
98D27504040000	1	TOOL-RESTRAINING, TK1
98D27504041000	1	TOOL-FLAP ADJUSTING
98D27504082000	2	TOOL - FLAP ADJUSTING, TRACK 4
98D27508001000	4	RIG SCALE FLAP
98D27508655000	2	RIG-SCALE,FLAP
98D27803500001	1	LOCKING TOOL ZERO POS
OR	OR
98D27803500002	1	LOCKING TOOL ZERO POS

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.06CMD9)	Silicone Adhesive Sealant-General Purpose One part legacy
(Material No.06LCG9)	Non Hardening Jointing Putty-Medium Temp. Area - -
(Material No.12ACC1)	Corrosion Preventive Compound-Heavy Duty Soft Film -
(Material No.14QFB1)	Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
193BB, 194BB, 573AB, 573CB, 575AB, 673AB, 673CB, 675AB

D. Expendable Parts

FIG.ITEM	DESIGNATION	IPC-CSN
54	COTTER PIN	AIPC 27-54-46-06-035
52	CRUSHABLE SPACER	AIPC 27-54-46-06-080
92	COTTER PIN	AIPC 57-52-21-02-110

E. Referenced Information

REFERENCE	DESIGNATION
TASK 07-11-00-581-001-A	Lifting for Aircraft Maintenance Operations
TASK 27-50-00-866-012-A	Manual Retraction of the Flaps
TASK 27-51-00-820-004-A	Adjustment of the Forward Eccentrics (Tracks 3 and 4)
TASK 27-51-00-820-010-A	Adjustment of the Flap Rollers
TASK 27-54-00-710-001-A	Operational Test of the Flap System
TASK 27-54-00-820-001-A	Adjustment of the Flap Drive System
TASK 27-54-61-000-001-A	Removal of the Inboard Flap
TASK 27-54-61-000-002-A	Removal of the Flap Kink-Seals and Cushion-Seals
TASK 27-54-61-400-001-A	Installation of the Inboard Flap
TASK 27-54-61-400-006-A	Installation of the Flap Kink-Seals and Cushion-Seals
TASK 27-54-62-000-001-A	Removal of the Outboard Flap
TASK 27-54-62-400-001-A	Installation of the Outboard Flap
TASK 27-54-63-400-001-A	Installation of the Flap Guide-Roller Assembly
TASK 57-51-37-000-002-A	Removal of the Access Panels 571AB(671AB), 573AB(673AB), 573BB(673BB), 573CB(673CB), 573EB(673EB)
TASK 57-51-37-000-004-A	Removal of the Access Panels 575AB(675AB), 575BB(675BB), 575CB(675CB), 575DB(675DB), 575EB(675EB), 575FB(675FB), 575GB(675GB), 575HB(675HB)
TASK 57-51-37-400-002-A	Installation of the Access Panels 571AB(671AB), 573AB(673AB), 573BB(673BB), 573CB(673CB), 573EB(673EB)
TASK 57-51-37-400-004-A	Installation of the Access Panels 575AB(675AB), 575BB(675BB), 575CB(675CB), 575DB(675DB), 575EB(675EB), 575FB(675FB), 575GB(675GB), 575HB(675HB)
TASK 57-55-11-010-001-A	To Lower the Flap Track No. 2 Movable Fairing for Access
TASK 57-55-11-010-002-A	To Lower the Flap Track No. 3 & No. 4 Movable Fairings for Access
Flap Rigging - General ** ON A/C NOT FOR ALL
Flap Rigging - General ** ON A/C NOT FOR ALL
Eccentric Bearings - General
Rigging Pin Installation
Rigging Kit Installation - Outboard Flap ** ON A/C NOT FOR ALL
Rigging Kit Installation - Outboard Flap ** ON A/C NOT FOR ALL
Main Eccentric Bearing - Adjustment, Track 2, 3 and 4
Rigging Dimensions - Outboard Flap ** ON A/C NOT FOR ALL
Rigging Dimensions - Outboard Flap ** ON A/C NOT FOR ALL
Label Positions - Flap Track 3 and 4
Label Positions - Flap Tracks 2, 3 and 4 ** ON A/C NOT FOR ALL
Label Position - Flap Track 3 ** ON A/C NOT FOR ALL
Rigging Kit Installation - Inboard Flap ** ON A/C NOT FOR ALL
Rigging Kit Installation - Inboard Flap ** ON A/C NOT FOR ALL
Main Eccentric Bearing Adjustment - Track 1 ** ON A/C NOT FOR ALL
Main Eccentric Bearing Adjustment - Track 1 ** ON A/C NOT FOR ALL
Rigging Dimension - Inboard Flap
Forward Eccentric Bearing - Track 1

3. Job Set-up
Subtask 27-51-00-941-079-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
(2) Put a WARNING NOTICE(S) on panel 114VU to tell persons not to operate the flap/slat control lever.

Subtask 27-51-00-860-074-A ** ON A/C NOT FOR ALL

B. Aircraft Maintenance Configuration
(1) Make sure that:

the fuel quantities in the wing tanks are symmetrical or that the wing tanks are empty
two engines are installed
or
no engines are installed.

(2) Make sure that the aircraft weight is:

on the landing gear (weight on wheels)
or
on jacks (Ref. AMM TASK 07-11-00-581-001).

Subtask 27-51-00-865-113-A ** ON A/C NOT FOR ALL

C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B07
121VU	FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2	8CV	Q21

Subtask 27-51-00-010-063-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT) below the applicable inboard or outboard flap.
(2) Remove the access panels for the applicable wing:
(a) For the LH wing, remove:

(b) For the RH wing, remove:

(3) For the inboard flap:
(a) Remove the fairing panels at track 1.
1 For the LH wing remove :

193BB (Ref. AMM TASK 27-54-61-000-001).

2 For the RH wing remove :

194BB (Ref. AMM TASK 27-54-61-000-001).

(b) Lower the flap track No. 2 movable fairing (Ref. AMM TASK 57-55-11-010-001).
(4) For the outboard flap:
(a) Lower the flap track No. 3 and the flap track No. 4 movable fairings (Ref. AMM TASK 57-55-11-010-002).
(5) Remove the 98D27803500001 LOCKING TOOL ZERO POS98D27803500002 LOCKING TOOL ZERO POS from the flap/slat control lever (installed when the movable fairings were lowered).
(6) Remove the flap kink seals (Ref. AMM TASK 27-54-61-000-002).
(7) Disconnect the interconnecting strut from the outboard flap (Ref. AMM TASK 27-54-62-000-001).
(8) Manually retract the flaps to the fully retracted position (Ref. AMM TASK 27-50-00-866-012).
(9) Install the 98D27803500001 LOCKING TOOL ZERO POS98D27803500002 LOCKING TOOL ZERO POS on the flap/slat control-lever.

4. Procedure
Subtask 27-51-00-820-083-A ** ON A/C NOT FOR ALL

A. Flap Rigging - General

Flap Rigging - General ** ON A/C NOT FOR ALL

Eccentric Bearings - General ** ON A/C NOT FOR ALL

(1) General:
(a) The position of a correctly rigged flap gives the correct relation between:

the flap trailing edge
and
the top surface of the wing..

In this position the correct aerodynamic conditions for the best flight performance are set.
(b) To rigg the flaps correctly, eccentric bearings in the attachments at the flap tracks are adjusted.
At each track there are two eccentric bearings:

the main eccentric bearing
the forward eccentric bearing.

(2) Main eccentric bearing:
The main eccentric bearing is the spherical bearing at the flap carriage attachment and is used for standard rigging. Movement of this bearing causes the complete flap to move vertically in relation to the wing.
You adjust the height of the complete flap.
(3) Forward eccentric bearing:
The forward eccentric bearing is on the flap drive-arm and is adjusted only for asymmetric rigging conditions (if this aircraft has an asymmetric rigging value).
For more information refer to ISI 27.54.00002.
You adjust only the trailing edge of the flap that means the trailing edge moves vertically.

Subtask 27-51-00-480-060-B ** ON A/C NOT FOR ALL

B. Install the Outboard Flap Rigging-Kit

Flap Rigging - General ** ON A/C NOT FOR ALL

Rigging Pin Installation ** ON A/C NOT FOR ALL

Rigging Kit Installation - Outboard Flap ** ON A/C NOT FOR ALL

(1) Install the 98D27504005000 PIN RIGGING-FLAPS (TRACK 1) (1) at track 1.
(2) Install the 98D27504006000 PIN-RIGGING, FLAPS (7) at tracks 2, 3 and 4.
(3) If you cannot install the 98D27504006000 PIN-RIGGING, FLAPS, do the adjustment of the flap drive system (Ref. AMM TASK 27-54-00-820-001).
(4) At tracks 3 and 4, install the parts of the 98D27504038001 KIT-FLAP RIGGING:
(a) Install the base assembly (23) on the flap track beam (28). Make sure that the aft dowels (25) touch the track beam end-stop (24).
(b) Move the two bottom clamps (26) into position below the flap track beam (28) and tighten the knurled screws (27).
(c) Move the fin (21) into position in the slot on the base assembly (23) and install the pin (22).
(d) Put the scale block (20) on the fin (21).

Subtask 27-51-00-480-060-C ** ON A/C NOT FOR ALL

B. Install the Outboard Flap Rigging-Kit

Flap Rigging - General ** ON A/C NOT FOR ALL

Rigging Pin Installation ** ON A/C NOT FOR ALL

Rigging Kit Installation - Outboard Flap ** ON A/C NOT FOR ALL

(1) Install the 98D27504005000 PIN RIGGING-FLAPS (TRACK 1) (1) at the track 1 position.
(2) Install the 98D27504006000 PIN-RIGGING, FLAPS (7) at the track 2, 3 and 4 positions.
(3) If you cannot install the 98D27504006000 PIN-RIGGING, FLAPS, do the adjustment of the flap drive system (Ref. AMM TASK 27-54-00-820-001).
(4) At the track 3 position only, install the part of the 98D27504038001 KIT-FLAP RIGGING:
(a) Install the base assembly (23) on the flap track beam (28). Make sure that the aft dowels (25) touch the track beam end-stop (24).
(b) Move the two bottom clamps (26) into position below the flap track beam (28) and tighten the knurled screws (27).
(c) Move the fin (21) into position in the slot on the base assembly (23) and install the pin (22).
(d) Put the scale block (20) on the fin (21).

Subtask 27-51-00-480-060-E ** ON A/C NOT FOR ALL

B. Install the Outboard Flap Rigging-Kit

Flap Rigging - General ** ON A/C NOT FOR ALL

Rigging Pin Installation ** ON A/C NOT FOR ALL

Rigging Kit Installation - Outboard Flap ** ON A/C NOT FOR ALL

Do not use the scale block from the rigging kit: Use the 98D27508655000 RIG-SCALE,FLAP or 98D27508001000 RIG SCALE FLAP for the adjustment procedure.

NOTE: The RIG SCALE FLAP (part number 98D27508001000) is the alternative part number for 3D-printing.

Subtask 27-51-00-820-073-C ** ON A/C NOT FOR ALL

C. Position of the Forward and Main Eccentric Bearings (Outboard Flap)

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

NOTE: The main eccentric bearings are spherical bearings installed in the flap attachment fittings at the flap carriages. A red paint mark on each bearing and fitting shows the zero datum position. The bearings are at the zero datum position when the red paint marks on the bearing and fitting are aligned.

(1) Before you set the main eccentric bearings to the zero datum position:
(a) Make sure that the forward eccentrics are in the zero datum position (Ref. AMM TASK 27-51-00-820-004).

NOTE: The forward eccentrics are in the zero datum position if the punched/painted marks on the forward eccentrics align.

(b) If these marks do not align, adjust the forward eccentrics to the punched/painted marks.
(c) If your aircraft is post modification 35900 and you find an asymmetrical offset value at the label (41) at track 3:
Do NOT adjust the forward eccentrics to the asymmetrical offset value (label 41 at track 3) at this time.
(2) On the carriage bolts (58) at the track 3 and track 4 positions:
(a) Remove and discard the cotter pin (54) from the nut (53).
(b) Remove these items:

the nut (53)
the crushable spacer (52)
the nut (55) and the washer (56)
the locking plate (51).

(3) Remove and discard the lockwire from the nuts (57) installed on the failsafe hooks.
(4) Loosen the nuts (57).

NOTE: These are loosened to give easier movement when the eccentric bearings are adjusted.

(5) At the track 3 and track 4 positions:
(a) Engage the 98D27504082000 TOOL - FLAP ADJUSTING, TRACK 4 with the splined bush in the flap carriage.
(b) Turn the splined bush until the red paint marks are aligned. Adjust the bearings at one track position and then the other in small equal increments.

NOTE: The splined bush engages with the main eccentric bearing. When the bush is turned, the eccentric bearing also turns.

Subtask 27-51-00-820-066-D ** ON A/C NOT FOR ALL

D. Adjustment (Rigging) of the Outboard Flap

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

Rigging Dimensions - Outboard Flap ** ON A/C NOT FOR ALL

(1) Use the TOOL FLAP ADJUSTING to adjust the main eccentric bearings. Adjust the bearings at one track position then the other in small, equal increments. At the track 3 and the track 4 positions, adjust the main eccentric bearings until:

at track 3, the top surface of the flap trailing edge aligns +/- 1.0 mm (0.0394 in.) with the zero line on the scale block (20)

NOTE: Look inboard from the outside of the flap track beam when you read the scale block.

at the outboard end of the flap, the dimension N (the vertical distance between the outer fixed shroud and the end of the flap) is zero +/- 1.0 mm (0.0394 in.).

Subtask 27-51-00-820-066-E ** ON A/C NOT FOR ALL

D. Adjustment (Rigging) of the Outboard Flap

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

Rigging Dimensions - Outboard Flap ** ON A/C NOT FOR ALL

the top surface of the flap trailing edge aligns +/- 1.0 mm (0.0394 in.) with the zero line on the scale block (20).

NOTE: Look inboard from the outside of the flap track beam when you read the scale block.

Subtask 27-51-00-820-066-H

D. Adjustment (Rigging) of the Outboard Flap

Label Positions - Flap Track 3 and 4

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

Rigging Dimensions - Outboard Flap

NOTE: Label (42) shows the shark-fin calibration value at track 4. Aircraft with this label used to have the outer fixed shroud as the datum point. The shark-fin uses the flap track beam as a datum. The shark-fin calibration value is the difference (distance) between the fixed shroud datum and the flap track beam datum. The value must be included when the position of the flap trailing edge is set.

with the zero line on the scale block (20), plus or minus 1.0 mm (0.0394 in.).

NOTE: Look inboard from the outside of the flap track beam when you read the scale block.

(b) At the track 4 position, the flap top surface aligns:

with the line on the scale block (20) which agrees with the calibration value on the track 4 label (42).

NOTE: Look inboard from the outside of the flap track beam when you read the scale block.

Subtask 27-51-00-820-066-M ** ON A/C NOT FOR ALL

D. Adjustment (Rigging) of the Outboard Flap
(This procedure includes the calibration value post modification 35900)

Label Positions - Flap Tracks 2, 3 and 4 ** ON A/C NOT FOR ALL

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

Rigging Dimensions - Outboard Flap ** ON A/C NOT FOR ALL

(1) Use the TOOL FLAP ADJUSTING to adjust the main eccentric bearings. Carefully adjust the two bearings at the same time in small, equal increments.
(2) At track 3 and track 4, adjust the main eccentric bearings until:

the top surface of the flap trailing edge aligns with the scale block (20) as follows:

(a) At track 3:
1 On flap arm 3, find the label (43) and read the value on the label (43).
2 Align the top surface of the flap trailing edge with this value on the scale block (20).
This value has a tolerance of +/- 1 mm (0.039 in.).

NOTE: You must look inboard from the outside of the flap track beam when you read the scale block.

3 If there is no value shown on the label (43), or there is no label attached to the flap arm:

align the top surface of the flap trailing edge with the zero mark +/- 1 mm (0.039 in.) on the scale block (20).

(b) At track 4:
1 On flap arm 4, find the label (43) and read the value on the label (43).
2 Align the top surface of the flap trailing edge with this value on the scale block (20).
This value has a tolerance of +/- 1 mm (0.039 in.).

NOTE: You must look inboard from the outside of the flap track beam when you read the scale block.

3 If there is no value shown on the label (43), or there is no label attached to the flap arm:

align the top surface of the flap trailing edge with the zero mark +/- 1 mm (0.039 in.) on the scale block (20).

Subtask 27-51-00-420-073-C ** ON A/C NOT FOR ALL

E. Remove the Adjusting Tools from the Main Eccentric Bearings of the Outboard Flap

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

(1) Remove the 98D27504082000 TOOL - FLAP ADJUSTING, TRACK 4 from the splined bush in the flap carriage at track 3 and track 4.
(2) At the track 3 and track 4 positions do as follows:
(a) On the carriage bolt (58) install these items:

the locking plate (51) (make sure that the main eccentric bearing, the splined bush and the locking plate (51) are correctly engaged)
a new AIPC 27-54-46-06-080 CRUSHABLE SPACER (52)
the nut (53).

(b) TORQUE the nut (53) to between 20 and 15 m.daN (147.49 and 110.62 lbf.ft )

.
(c) Safety the nut (53) with a new AIPC 27-54-46-06-035 COTTER PIN (54).
(d) Install the washer (56) and the nut (55).
(e) TORQUE the nuts (57) on the failsafe hooks to between 0.12 and 0.05 m.daN (10.62 and 4.42 lbf.in )

.
(f) Safety the nuts (57) with lockwire, 14QFB1Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -.

Subtask 27-51-00-820-074-D ** ON A/C NOT FOR ALL

F. Complete the Adjustment (Rigging) of the Outboard Flap

Label Position - Flap Track 3 ** ON A/C NOT FOR ALL

(1) If you find an asymmetrical offset value on the label (41) at track 3, it is necessary to adjust the forward eccentrics at the tracks 3 and 4.

NOTE: The label (41) shows the asymmetrical offset value. This is the adjustment applied to the forward eccentric bearings in the flap drive strut at tracks 3 and 4. The adjustment is necessary on some aircraft to give the correct aerodynamic balance:

a plus (+) or (up) value shows that the flap trailing edge must be moved up
a minus (-) or (down) value shows that the flap trailing edge must be moved down
a zero (0) value shows that no adjustment is necessary.

(2) Adjust the forward eccentrics at track 3 and track 4 in sequence (in small increments).

Rigging Dimensions - Outboard Flap ** ON A/C NOT FOR ALL

For details refer to the task 'Adjustment of the Forward Eccentrics' (Ref. AMM TASK 27-51-00-820-004).
(a) At track 3:
1 For a (+) or (up) value, the top surface of the flap must align (+/- 1.0 mm (0.0394 in.)) with:

the line above zero on the scale block (20) which is the same as the label value.

2 For a (-) or (down) value, the top surface of the flap must align (+/- 1.0 mm (0.0394 in.)) with:

the line below zero on the scale block (20) which is the same as the label value.

NOTE: The scale block has 1 millimeter graduations.

(b) At the outboard end of the flap measure the dimension N (the vertical distance between the outer fixed shroud and the top surface of the flap):
1 For a (+) or (up) value, the distance must be zero +/- 1.0 mm (0.0394 in.) plus the value shown.
2 For a (-) or (down) value, the distance must be zero +/- 1.0 mm (0.0394 in.) minus the value shown.
(c) After the adjustment: Safety the forward eccentrics (Ref. AMM TASK 27-54-62-400-001).
(3) At the track 3 position, remove the parts of the 98D27504038001 KIT-FLAP RIGGING:

Rigging Kit Installation - Outboard Flap ** ON A/C NOT FOR ALL

(a) Remove the scale block (20).
(b) Remove the pin (22) and remove the fin (21) from the base assembly (23).
(c) Loosen the knurled screws (27) and remove the base assembly (23) from the flap track beam (28).
(4) Measure the clearance of the flap guide-roller and adjust if necessary (Ref. AMM TASK 27-54-63-400-001).

Subtask 27-51-00-820-074-E ** ON A/C NOT FOR ALL

F. Complete the Adjustment (Rigging) of the Outboard Flap

Label Position - Flap Track 3 ** ON A/C NOT FOR ALL

(1) If you find an asymmetrical offset value on the label (41) at track 3, it is necessary to adjust the forward eccentrics at the tracks 3 and 4.

a plus (+) or (up) value shows that the flap trailing edge must be moved up.
a minus (-) or (down) value shows that the flap trailing edge must be moved down.
a zero (0) value shows that no adjustment is necessary.

(2) At tracks 3 and 4:

Do the adjustment of the forward eccentrics (Ref. AMM TASK 27-51-00-820-004).

(3) After the adjustment: Safety the forward eccentrics (Ref. AMM TASK 27-54-62-400-001).
(4) At tracks 3 and 4, remove the parts of the 98D27504038001 KIT-FLAP RIGGING:

Rigging Kit Installation - Outboard Flap ** ON A/C NOT FOR ALL

(a) Remove the scale block (20).
(b) Remove the pin (22) and remove the fin (21) from the base assembly (23).
(c) Loosen the knurled screws (27) and remove the base assembly (23) from the flap track beam (28).
(5) Measure the clearance of the flap guide-roller and adjust if necessary (Ref. AMM TASK 27-54-63-400-001).

Subtask 27-51-00-820-074-G

F. Complete the Adjustment (Rigging) of the Outboard Flap

Label Positions - Flap Track 3 and 4

(1) If you find an asymmetrical offset value on the label (41) at track 3, it is necessary to adjust the forward eccentrics at the tracks 3 and 4.

NOTE: The label (41) shows the asymmetric offset value. This is the adjustment applied to the forward eccentric bearings in the flap drive strut at tracks 3 and 4. The adjustment is necessary on some aircraft to give the correct aerodynamic balance:

a plus (+) or (up) value shows that the flap trailing edge must be moved up.
a minus (-) or (down) value shows that the flap trailing edge must be moved down.
a zero (0) value shows that no adjustment is necessary.

(2) At tracks 3 and 4:

Do the adjustment of the forward eccentrics (Ref. AMM TASK 27-51-00-820-004).

(3) After the adjustment: Safety the forward eccentrics (Ref. AMM TASK 27-54-62-400-001).
(4) At tracks 3 and 4, remove the parts of the 98D27504038001 KIT-FLAP RIGGING:

Rigging Kit Installation - Outboard Flap

(a) Remove the scale block (20).
(b) Remove the pin (22) and remove the fin (21) from the base assembly (23).
(c) Loosen the knurled screws (27) and remove the base assembly (23) from the flap track beam (28).
(5) Measure the clearance of the flap guide-roller and adjust if necessary (Ref. AMM TASK 27-54-63-400-001).

Subtask 27-51-00-820-074-H ** ON A/C NOT FOR ALL

F. Complete the Adjustment (Rigging) of the Outboard Flap

Label Positions - Flap Tracks 2, 3 and 4 ** ON A/C NOT FOR ALL

(1) If you find an asymmetric offset value on the label (41) at track 3, it is
necessary to adjust the forward eccentrics at the tracks 3 and 4.

a plus (+) or (up) value shows that the flap trailing edge must be moved up.
a minus (-) or (down) value shows that the flap trailing edge must be moved down.
a zero (0) value shows that no adjustment is necessary.

(2) At tracks 3 and 4:

Do the adjustment of the forward eccentrics (Ref. AMM TASK 27-51-00-820-004).

(3) After the adjustment: Safety the forward eccentrics (Ref. AMM TASK 27-54-62-400-001).
(4) At tracks 3 and 4, remove the parts of the 98D27504038001 KIT-FLAP RIGGING:

Rigging Kit Installation - Outboard Flap ** ON A/C NOT FOR ALL

(a) Remove the scale block (20) 98D27508655000 RIG-SCALE,FLAP or 98D27508001000 RIG SCALE FLAP.
(b) Remove the pin (22) and remove the fin (21) from the base assembly (23).
(c) Loosen the knurled screws (27) and remove the base assembly (23) from the flap track beam (28).
(5) Measure the clearance of the flap guide-roller and adjust if necessary (Ref. AMM TASK 27-54-63-400-001).

Subtask 27-51-00-480-061-B ** ON A/C NOT FOR ALL

G. Install the Inboard Flap Rigging-Kit

Rigging Pin Installation ** ON A/C NOT FOR ALL

Rigging Kit Installation - Inboard Flap ** ON A/C NOT FOR ALL

(1) Install the 98D27504005000 PIN RIGGING-FLAPS (TRACK 1) (1) in the drive-lever (5) at track 1.
(2) At the track 1 position, install the 98D27504039000 TOOL-RESTRAINING,TK1.
(a) Put the body assembly (65) in position on the flap track beam (63).
(b) Connect the stop (67) to the flap carriage (60).
(c) Assemble the side-plate (62) and the thumb-nut (61) to the body assembly (65).
(d) Adjust the screw (66) with the knob (64) until the flap carriage (60) is held in position.
(3) At the track 2 position, install the parts of the 98D27504038001 KIT-FLAP RIGGING:
(a) Install the base assembly (71) on the flap track beam (76). Make sure that the aft dowels (73) touch the track beam end-stop (72).
(b) Move the two bottom clamps (74) into position below the flap track beam (76) and tighten the knurled screws (75).
(c) Move the fin (69) into position on the base assembly (71) and install the pin (70).
(d) Put the scale block (68) on the fin (69).
(4) Disconnect the flap drive-arm (4) and the rotary actuator drive-lever (5) at the track 1 position (Ref. AMM TASK 27-54-61-000-001).

Subtask 27-51-00-480-061-C ** ON A/C NOT FOR ALL

G. Install the Inboard Flap Rigging-Kit

Rigging Pin Installation ** ON A/C NOT FOR ALL

Rigging Kit Installation - Inboard Flap ** ON A/C NOT FOR ALL

(1) Install the 98D27504005000 PIN RIGGING-FLAPS (TRACK 1) (1) in the drive-lever (5) at track 1.
(2) At the track 1 position, install the 98D27504040000 TOOL-RESTRAINING, TK1.
(a) Put the body assembly (64) in position on the flap track beam (62).
(b) Connect the stop (66) to the flap carriage (60).
(c) Install the spigot (61) through the flap track beam (62) into the body assembly (64).
(d) Adjust the screw (65) with the knob (63) until the flap carriage (60) is held in position.
(3) At the track 2 position, install the parts of the 98D27504038001 KIT-FLAP RIGGING:
(a) Install the base assembly (71) on the flap track beam (76). Make sure that the aft dowels (73) touch the track beam end-stop (72).
(b) Move the two bottom clamps (74) into position below the flap track beam (76) and tighten the knurled screws (75).
(c) Move the fin (69) into position on the base assembly (71) and install the pin (70).
(d) Put the scale block (68) on the fin (69).
(4) Disconnect the flap drive-arm (4) and the rotary actuator drive-lever (5) at the track 1 position (Ref. AMM TASK 27-54-61-000-001).

Subtask 27-51-00-480-061-E ** ON A/C NOT FOR ALL

G. Install the Inboard Flap Rigging-Kit

Rigging Pin Installation ** ON A/C NOT FOR ALL

Rigging Kit Installation - Inboard Flap ** ON A/C NOT FOR ALL

Do not use the scale block from the rigging kit: Use the 98D27508655000 RIG-SCALE,FLAP or 98D27508001000 RIG SCALE FLAP for the adjustment procedure.

NOTE: The RIG SCALE FLAP (part number 98D27508001000) is the alternative part number for 3D-printing.

(4) Disconnect the flap drive-arm (4) and the rotary actuator drive-lever (5) at the track 1 position (Ref. AMM TASK 27-54-61-000-001).

Subtask 27-51-00-820-075-E ** ON A/C NOT FOR ALL

H. Set the Main Eccentric Bearings of the Inboard Flap to the Zero Datum Position

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

Main Eccentric Bearing Adjustment - Track 1 ** ON A/C NOT FOR ALL

NOTE: The main eccentric bearings are spherical bearings installed in the flap attachment fittings at the flap carriages.

At track 1, an eccentric bush (86) is installed in the bearing (87). A pin on the eccentric bush (86) engages with the toothplate (85). The bearing (87) is at zero datum when the pin on the eccentric bush (86) is at the position shown.

Main Eccentric Bearing Adjustment - Track 1 ** ON A/C NOT FOR ALL

Detail D.

At track 2, red paint marks on the bearing and on the fitting show the zero datum position. The bearing is at the zero datum position when the red paint marks are aligned.

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

Adjust the bearings at one position then the other in small increments.

(1) At the track 1 position set the main eccentric bearing to the zero datum position as follows:
(a) Remove these items:

the bolt (80)
the tabwasher (81)
the stop (82)
the nut (83)
the lockwasher (84)
the toothplate (85).

(b) Use the 98D27504002000 FLAP ADJUSTING TOOL to move the eccentric bush (86) to the position shown.

Main Eccentric Bearing Adjustment - Track 1 ** ON A/C NOT FOR ALL

Detail D.
(2) At the track 2 position set the main eccentric bearing to the zero datum position as follows:

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

(a) Remove and discard the lockwire from the nuts (57) installed on the failsafe hooks.
(b) Loosen the nuts (57).

NOTE: These are loosened to give easier movement when the eccentric bearings are adjusted.

the nut (53)
the crushable spacer (52)
the nut (55) and the washer (56)
the locking plate (51).

(e) Engage the 98D27504082000 TOOL - FLAP ADJUSTING, TRACK 4 with the splined bush in the flap carriage.
(f) Turn the splined bush until the red paint marks are aligned.

NOTE: The splined bush engages with the main eccentric bearing. When the bush is turned the eccentric bearing also turns.

Subtask 27-51-00-820-075-H ** ON A/C NOT FOR ALL

H. Set the Main Eccentric Bearings of the Inboard Flap to the Zero Datum Position

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

Main Eccentric Bearing Adjustment - Track 1 ** ON A/C NOT FOR ALL

Detail D.

At track 2, red paint marks on the bearing and on the fitting show the zero datum position. The bearing is at the zero datum position when the red paint marks are aligned.

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

Adjust the bearings at one position then the other in small increments.

(1) At the track 1 position, set the main eccentric bearing to the zero datum position as follows:
(a) Remove these items:

the bolt (80)
the tabwasher (81)
the stop (82)
the nut (83)
the lockwasher (84)
the toothplate (85).

(b) Use the 98D27504041000 TOOL-FLAP ADJUSTING to move the eccentric bush (86) to the position shown.

Main Eccentric Bearing Adjustment - Track 1 ** ON A/C NOT FOR ALL

Detail D.
(2) At the track 2 position, set the main eccentric bearing to the zero datum position as follows:

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

(a) Remove and discard the lockwire from the nuts (57) installed on the failsafe hooks.
(b) Loosen the nuts (57).

NOTE: These nuts must be loose to make sure that the movement is easy when you adjust the eccentric bearings.

the nut (53)
the crushable spacer (52)
the nut (55) and the washer (56)
the locking plate (51).

(e) Engage the 98D27504082000 TOOL - FLAP ADJUSTING, TRACK 4 with the splined bush in the flap carriage.
(f) Turn the splined bush until the red paint marks are aligned.

NOTE: The splined bush engages with the main eccentric bearing. When you turn the bush, the eccentric bearing also turns.

Subtask 27-51-00-820-067-D ** ON A/C NOT FOR ALL

I. Adjustment (Rigging) of the Inboard Flap

Rigging Kit Installation - Inboard Flap ** ON A/C NOT FOR ALL

Rigging Dimension - Inboard Flap ** ON A/C NOT FOR ALL

(1) Make sure that scale block (68) is in position on the fin (69).
(2) Use the TOOL FLAP ADJUSTING to adjust the main eccentric bearings. Adjust the bearings at one track position then the other in small increments. Set the inboard flap as follows:
(a) At the track 1 and the track 2 positions, adjust the main eccentric bearings until:
1 At track 2, the top surface of the flap aligns +/- 1.0 mm (0.0394 in.) with the zero line on the scale block (68).

NOTE: Look inboard from the outside of the flap track beam when you read the scale block.

2 The dimension S (between the bottom surface of the shroud box trailing-edge and the top surface of the flap at the WX500 position) is between 4.5 mm (0.1772 in.) and 8.0 mm (0.3150 in.).
(3) At the track 1 position:
(a) Measure the dimension Q (between the flap drive-arm (4) and the rotary actuator drive-lever (5)).
(b) If the dimension Q is less than 2 mm (0.0787 in.), a force of not more than 25 kg (55.1156 lb) can be applied to the fork of the flap drive-arm (4) to align the holes.
(c) Loosely install the bolt (6).
(d) If the dimension Q is more than 2 mm (0.0787 in.), then adjust the forward eccentric (in the flap drive-arm) until the dimension Q is not more than 2 mm (0.0787 in.). To do this:

Forward Eccentric Bearing - Track 1 ** ON A/C NOT FOR ALL

1 Remove and discard the cotter pin (92).
2 Remove the nut (95), the washer (94) and the serrated lockwasher (96).
3 Loosen the nut (91) sufficiently to let the eccentric bolt (97) move.
4 Turn the eccentric bolt (97) until the dimension Q is not more than 2 mm (0.0787 in.) and loosely install the bolt (6).
(4) Remove the 98D27504039000 TOOL-RESTRAINING,TK1 from the flap track 1 beam (Ref. Para 4.K.(2)).
(5) Do a check of the flap rigged position again to make sure that it is in the specified limits. If the flap rigged position is not correct:
(a) Install the 98D27504039000 TOOL-RESTRAINING,TK1 on the flap track 1 beam (Ref. Para 4.F.(2)).
(b) Disconnect the track 1 flap drive levers (4) and (5).
(c) Put the track 1 main eccentric bearing back to its zero datum position.
(d) Do steps (2) thru (6) again until the flap is in the correct rigged position.
(e) Torque the nut (91) to between 2.8 and 2.6 m.daN (20.65 and 19.17 lbf.ft )

and install a new AIPC 57-52-21-02-110 COTTER PIN (92).
(f) Install the serrated lockwasher (96) with the end of the bolt (93) through its hole.
(6) Apply a layer of Non Hardening Jointing Putty-Medium Temp. Area - - (Material No.06LCG9) to the threads of the bolt (93).
(7) Install the washer (94) and the nut (95).
(8) Apply a layer of Corrosion Preventive Compound-Heavy Duty Soft Film - (Material No.12ACC1) to:

the cotter pin (92), the nuts (91) and (95), the washer (94) and the eccentric bolt (97).

Subtask 27-51-00-820-067-F ** ON A/C NOT FOR ALL

I. Adjustment (Rigging) of the Inboard Flap

Rigging Kit Installation - Inboard Flap ** ON A/C NOT FOR ALL

Rigging Dimension - Inboard Flap ** ON A/C NOT FOR ALL

NOTE: Look inboard from the outside of the flap track beam when you read the scale block.

Forward Eccentric Bearing - Track 1 ** ON A/C NOT FOR ALL

1 Remove and discard the cotter pin (92).
2 Remove the nut (95), the washer (94) and the serrated lockwasher (96).
3 Loosen the nut (91) sufficiently to let the eccentric bolt (97) move.
4 Turn the eccentric bolt (97) until the dimension Q is not more than 2 mm (0.0787 in.) and loosely install the bolt (6).
(4) Remove the 98D27504040000 TOOL-RESTRAINING, TK1 from the flap track 1 beam (Ref. Para 4.K.(2)).
(5) Do a check of the flap rigged position again to make sure that it is in the specified limits. If the flap rigged position is not correct:
(a) Install the 98D27504040000 TOOL-RESTRAINING, TK1 on the flap track 1 beam (Ref. Para 4.F.(2)).
(b) Disconnect the track 1 flap drive levers (4) and (5).
(c) Put the track 1 main eccentric bearing back to its zero datum position.
(d) Do steps (2) thru (6) again until the flap is in the correct rigged position.
(e) Torque the nut (91) to between 2.8 and 2.6 m.daN (20.65 and 19.17 lbf.ft )

the cotter pin (92), the nuts (91) and (95), the washer (94) and the eccentric bolt (97).

Subtask 27-51-00-820-067-G ** ON A/C NOT FOR ALL

I. Adjustment (Rigging) of the Inboard Flap
(This procedure includes the calibration value post modification 35900)

Label Positions - Flap Tracks 2, 3 and 4 ** ON A/C NOT FOR ALL

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

Main Eccentric Bearing Adjustment - Track 1 ** ON A/C NOT FOR ALL

(1) Use the TOOL FLAP ADJUSTING to adjust the main eccentric bearings. Carefully adjust the two bearings at the same time in small, equal increments.
(2) At track 1 and track 2, adjust the main eccentric bearings until:
(a) At track 2:
1 On flap arm 2, find the label (43) and read the value on the label (43).
2 Align the top surface of the flap trailing edge with this value on the scale block (68).
This value has a tolerance of +/- 1 mm (0.039 in.).

NOTE: You must look inboard from the outside of the flap track beam when you read the scale block.

3 If there is no value on the label (43), or there is no label attached to the flap arm:

align the top surface of the flap trailing edge with the zero mark on the scale block (68).

(b) Near track 1 (refer to section D-D at the figure 'Rigging Dimension'):

Rigging Dimension - Inboard Flap ** ON A/C NOT FOR ALL

Adjust the main eccentric bearing until dimension S (between the bottom surface of the shroud-box trailing edge and the top surface of the flap at the WX500 position) is between 4.5 mm (0.177 in.) and 8.0 mm (0.315 in.).

(3) At track 1:
(a) Measure dimension Q (between the flap drive-arm (4) and the rotary actuator drive-lever (5)).

Rigging Pin Installation ** ON A/C NOT FOR ALL

(b) If dimension Q is less than 2 mm (0.0787 in.), you can apply a force of not more than 25 kg (55.1156 lb) to the fork of the flap drive-arm (4) to align the holes.
(c) Loosely install the bolt (6).
(d) If dimension Q is more than 2 mm (0.0787 in.), adjust the forward eccentric (in the flap drive-arm) until dimension Q is not more than 2 mm (0.0787 in.). To do this:

Forward Eccentric Bearing - Track 1 ** ON A/C NOT FOR ALL

1 Remove and discard the cotter pin (92).
2 Remove the nut (95), the washer (94) and the serrated lockwasher (96).
3 Loosen the nut (91) sufficiently to let the eccentric bolt (97) move.
4 Turn the eccentric bolt (97) until dimension Q is not more than 2 mm (0.0787 in.) and loosely install the bolt (6).
(4) Remove the 98D27504040000 TOOL-RESTRAINING, TK1 from the flap track 1 beam (Ref. Para 4.K.(2)) attached to the flap arm:
(5) Do a check of the flap rigged position again to make sure that it is in the specified limits. If the flap rigged position is not correct:
(a) Install the 98D27504040000 TOOL-RESTRAINING, TK1 on the flap track 1 beam (Ref. Para 4.F.(2)).
(b) Disconnect the track 1 flap drive levers (4) and (5).
(c) Put the track 1 main eccentric bearing back to its zero datum position.
(d) Do steps (2) thru (6) again until the flap is in the correct rigged position.
(e) Torque the nut (91) to between 2.8 and 2.6 m.daN (20.65 and 19.17 lbf.ft )

and install a new AIPC 57-52-21-02-110 COTTER PIN (92).
(f) Install the serrated lockwasher (96) with the end of the bolt (93) through its hole.
(6) Apply a layer of the zinc chromate putty Non Hardening Jointing Putty-Medium Temp. Area - - (Material No.06LCG9) to the threads of the bolt (93).
(7) Install the washer (94) and the nut (95).
(8) Apply a layer of the Corrosion Preventive Compound-Heavy Duty Soft Film - (Material No.12ACC1) to:

the cotter pin (92), the nuts (91) and (95), the washer (94) and the eccentric bolt (97).

Subtask 27-51-00-420-075-E ** ON A/C NOT FOR ALL

J. Remove the Adjusting Tools From the Main Eccentric Bearings of the Inboard Flap

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

Main Eccentric Bearing Adjustment - Track 1 ** ON A/C NOT FOR ALL

(1) At track 1:
(a) Remove the 98D27504002000 FLAP ADJUSTING TOOL from the eccentric bush (86).
(b) Install the toothplate (85), the lockwasher (84) and the nut (83).
(c) TORQUE the nut (83) using the 98D27504035000 TORQUE ADAPTER-TRUNNION NUT to between 7.0 and 5.4 m.daN (51.62 and 39.82 lbf.ft )

.
(d) Lock the nut (83) with the lockwasher (84).
(e) Apply a layer of Silicone Adhesive Sealant-General Purpose One part legacy (Material No.06CMD9) to the stop (82).
(f) Install the stop (82), the tabwasher (81) and the bolt (80).
(g) TORQUE the bolt (80) to between 1.5 and 1.0 m.daN (132.74 and 88.50 lbf.in )

.
(h) Lock the bolt (80) with the tabwasher (81).
(2) At track 2:
(a) On the carriage bolt (58) install these items:

the locking plate (51) (make sure that the main eccentric bearing, the splined bush and the locking plate (51) are correctly engaged)

a new AIPC 27-54-46-06-080 CRUSHABLE SPACER (52)
the nut (53).

(b) TORQUE the nut (53) to between 20 and 15 m.daN (147.49 and 110.62 lbf.ft )

.
(f) Safety the nuts (57) with 14QFB1Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -.

Subtask 27-51-00-420-075-I ** ON A/C NOT FOR ALL

J. Remove the Adjusting Tools from the Main Eccentric Bearings of the Inboard Flap

Main Eccentric Bearing - Adjustment, Track 2, 3 and 4 ** ON A/C NOT FOR ALL

Main Eccentric Bearing Adjustment - Track 1 ** ON A/C NOT FOR ALL

(1) At track 1:
(a) Remove the 98D27504041000 TOOL-FLAP ADJUSTING from the eccentric bush (86).
(b) Install the toothplate (85), the lockwasher (84) and the nut (83).
(c) TORQUE the nut (83) with the 98D27504035000 TORQUE ADAPTER-TRUNNION NUT to between 7.0 and 5.4 m.daN (51.62 and 39.82 lbf.ft )

.
(d) Lock the nut (83) with the lockwasher (84).

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

(e) Apply a layer of Silicone Adhesive Sealant-General Purpose One part legacy (Material No.06CMD9) to the stop (82).
(f) Install the stop (82), the tabwasher (81) and the bolt (80).
(g) TORQUE the bolt (80) to between 1.5 and 1.0 m.daN (132.74 and 88.50 lbf.in )

.
(h) Lock the bolt (80) with the tabwasher (81).
(2) At track 2:
(a) On the carriage bolt (58) install these items:

the locking plate (51) (make sure that the main eccentric bearing, the splined bush and the locking plate (51) are correctly engaged)

a new AIPC 27-54-46-06-080 CRUSHABLE SPACER (52)
the nut (53).

(b) TORQUE the nut (53) to between 20 and 15 m.daN (147.49 and 110.62 lbf.ft )

.
(f) Safety the nuts (57) with 14QFB1Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -.

Subtask 27-51-00-820-068-B ** ON A/C NOT FOR ALL

K. Completion of the Flap Rigging Procedure

Rigging Pin Installation ** ON A/C NOT FOR ALL

Rigging Kit Installation - Inboard Flap ** ON A/C NOT FOR ALL

(1) At the track 1 position, complete the installation of the flap drive levers (4) and (5) (Ref. AMM TASK 27-54-61-400-001).
(2) At the track 1 position, remove the 98D27504040000 TOOL-RESTRAINING, TK1 from the flap track 1 beam as follows:
(a) Remove the spigot (62) from the body assembly (64).
(b) Disconnect the stop (66) from the track beam (62).
(c) Remove the body assembly (64) from the flap track beam (62).
(3) At the track 2 position, remove the parts of 98D27504038001 KIT-FLAP RIGGING as follows:
(a) Remove the scale block (68) from the fin (69).
(b) Remove the pin (70) and remove the fin (69) from the base assembly (71).
(c) Loosen the knurled screws (75) and remove the base assembly (71) from the flap track beam (76).
(4) Remove all the rigging pins (1) and (7).
(5) Install the adaptor drive on the gearbox.
(6) Use the pneumatic wrench to turn the adaptor drive and fully extend and retract the flaps. Make sure that the flaps operate correctly.
(7) Install the rigging pin (1) at the track 1 position.

Subtask 27-51-00-820-068-C ** ON A/C NOT FOR ALL

K. Completion of the Flap Rigging Procedure

Rigging Pin Installation ** ON A/C NOT FOR ALL

Rigging Kit Installation - Inboard Flap ** ON A/C NOT FOR ALL

(1) At the track 1 position, complete the installation of the flap drive levers (4) and (5) (Ref. AMM TASK 27-54-61-400-001).
(2) At the track 1 position, remove the 98D27504039000 TOOL-RESTRAINING,TK1 from the flap track 1 beam as follows:
(a) Remove the thumb-nut (61) and the side-plate (62) from the body assembly (65).
(b) Disconnect the stop (67) from the flap carriage (60).
(c) Remove the body assembly (65) from the flap track beam (63).
(3) At the track 2 position, remove the parts of the 98D27504038001 KIT-FLAP RIGGING as follows:
(a) Remove the scale block (68) from the fin (69).
(b) Remove the pin (70) and remove the fin (69) from the base assembly (71).
(c) Loosen the knurled screws (75) and remove the base assembly (71) from the flap track beam (76).
(4) Remove all the rigging pins (1) and (7).
(5) Install the adaptor drive on the gearbox.
(6) Use the pneumatic wrench to turn the adaptor drive and fully extend and retract the flaps. Make sure that the flaps operate correctly.
(7) Install the rigging pin (1) at the track 1 position.

Subtask 27-51-00-820-068-E ** ON A/C NOT FOR ALL

K. Complete the Adjustment (Rigging) of the Inboard Flap

Rigging Pin Installation ** ON A/C NOT FOR ALL

Rigging Kit Installation - Inboard Flap ** ON A/C NOT FOR ALL

(1) At the track 1 position, complete the installation of the flap drive levers (4) and (5) (Ref. AMM TASK 27-54-61-400-001).
(2) At the track 1 position, remove the 98D27504040000 TOOL-RESTRAINING, TK1 from the flap track 1 beam as follows:
(a) Remove the spigot (62) from the body assembly (64).
(b) Disconnect the stop (66) from the track beam (62).
(c) Remove the body assembly (64) from the flap track beam (62).
(3) At the track 2 position, remove the parts of the 98D27504038001 KIT-FLAP RIGGING as follows:
(a) Remove the scale block (68) 98D27508655000 RIG-SCALE,FLAP or 98D27508001000 RIG SCALE FLAP from the fin (69).
(b) Remove the pin (70) and remove the fin (69) from the base assembly (71).
(c) Loosen the knurled screws (75) and remove the base assembly (71) from the flap track beam (76).
(4) Remove all the rigging pins (1) and (7).
(5) Install the adaptor drive on the gearbox.
(6) Use the pneumatic wrench to turn the adaptor drive and fully extend and retract the flaps. Make sure that the flaps operate correctly.
(7) Install the rigging pin (1) at the track 1 position.

Subtask 27-51-00-820-069-A ** ON A/C NOT FOR ALL

L. Alignment of the Inboard and Outboard Flap Cruise Rollers
(1) Make sure that the alignment of all the cruise rollers and the outer roller is correct (Ref. AMM TASK 27-51-00-820-010).

Subtask 27-51-00-420-076-A ** ON A/C NOT FOR ALL

M. Completion of the Flap Connection
(1) Connect the interconnecting strut to the outboard flap (Ref. AMM TASK 27-54-62-400-001).
(2) Install the flap kink seals (Ref. AMM TASK 27-54-61-400-006).

Subtask 27-51-00-710-070-A ** ON A/C NOT FOR ALL

N. Operational Test of the Flap System
(1) Remove the 98D27803500001 LOCKING TOOL ZERO POS98D27803500002 LOCKING TOOL ZERO POS from the flap/slat control lever.
(2) Do an operational test of the flap system (Ref. AMM TASK 27-54-00-710-001).

5. Close-up
Subtask 27-51-00-410-060-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the access panels:
(a) For the LH wing, install:

(b) For the RH wing, install:

Subtask 27-51-00-942-079-A ** ON A/C NOT FOR ALL

B. Removal of Equipment
(1) Remove the safety barriers.
(2) Remove the WARNING NOTICE(S).
(3) Remove the access platform(s).
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.03.31 23:52:25 UTC