DOC AIRBUS | AMM A320FInstallation of the Elevator Servo Control Actuator Mode Selector Valve Transducer MSVT
TASK 27-34-51-400-005-A
Installation of the Elevator Servo Control Actuator Mode Selector Valve Transducer MSVT
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Referenced Information
3. Job Set-up
Subtask 27-34-51-860-067-A
Subtask 27-34-51-420-057-A
Subtask 27-34-51-410-055-A
[Rev.10 from 2021]
2026.03.31 23:50:33 UTC
Installation of the Elevator Servo Control Actuator Mode Selector Valve Transducer MSVT
WARNING:
MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.
WARNING:
MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.
WARNING:
PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
WARNING:
YOU MUST PUT ON AND ATTACH A SAFETY HARNESS BEFORE YOU START WORK:
- ON THE THS OR IN THE REAR FUSELAGE
- ON TOP OF THE WINGS OR PYLONS.
CAUTION:
DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF CARBONFIBER REINFORCED PLASTIC.
NOTE: The installation of the servo control actuator 34CE1 mode selector valve transducer is given. The installation of the servo control actuator 34CE2, 34CE3 and 34CE4 mode selector transducer valves are the same.
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE |
| No specific | 1 | WARNING NOTICE(S) |
| No specific | Torque wrench: range to between 0.41 and 0.33 m.daN (36.28 and 29.20 lbf.in )  | |
| 98D27309001000 | 1 | NEUTRAL SETTING TOOL - ELEVATOR |
| 98D27903500000 | 2 | PIN-SIDE STICK LOCKING |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.03HBD9) | Synthetic Ester base Grease-General Purpose Low Temp - |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 27-34-00-710-001-A | Operational Test of the Elevator and Hydraulic Actuation |
| TASK 29-10-00-864-001-A | Depressurize the Green Hydraulic System |
| TASK 29-10-00-864-002-A | Depressurize the Yellow Hydraulic System |
| TASK 29-10-00-864-003-A | Depressurize the Blue Hydraulic System |
| TASK 29-14-00-614-001-A | Depressurization of the Hydraulic Reservoirs |
| TASK 55-13-11-000-001-A | Remove/Open of the Trimmable Horizontal Stabilizer (THS) Trailing-Edge Access-Panels |
| TASK 55-13-11-400-001-A | Install/Close of the Trimmable Horizontal Stabilizer (THS) Trailing-Edge Access-Panels |
Elevator Servo-Control Actuator Mode Selector Valve TransducerSubtask 27-34-51-860-067-A
A. Aircraft Maintenance Configuration
(1) Make sure that the elevators and the horizontal stabilizer are set to the neutral position.
(2) Make sure that the 98D27903500000 PIN-SIDE STICK LOCKING are in position in the CAPT and F/O side stick controllers.
(3) Make sure that the 98D27309001000 NEUTRAL SETTING TOOL - ELEVATOR is installed on the elevator.
(4) Make sure that the hydraulic systems are depressurized (Ref. AMM TASK 29-10-00-864-001), (Ref. AMM TASK 29-10-00-864-002), (Ref. AMM TASK 29-10-00-864-003).
(5) Make sure that the hydraulic reservoirs are depressurized (Ref. AMM TASK 29-14-00-614-001).
(6) Make sure that the WARNING NOTICE(S) are in position in the flight compartment to tell persons not to operate the flight controls.
(7) Make sure that the WARNING NOTICE(S) are in position to tell persons not to operate the hydraulic systems.
(8) Make sure that the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE is in position at zone 334 and/or zone 344.
(9) Make sure that access panels 334DB and/or 344DB are open (Ref. AMM TASK 55-13-11-000-001).
Subtask 27-34-51-865-079-A (1) Make sure that the elevators and the horizontal stabilizer are set to the neutral position.
(2) Make sure that the 98D27903500000 PIN-SIDE STICK LOCKING are in position in the CAPT and F/O side stick controllers.
(3) Make sure that the 98D27309001000 NEUTRAL SETTING TOOL - ELEVATOR is installed on the elevator.
(4) Make sure that the hydraulic systems are depressurized (Ref. AMM TASK 29-10-00-864-001), (Ref. AMM TASK 29-10-00-864-002), (Ref. AMM TASK 29-10-00-864-003).
(5) Make sure that the hydraulic reservoirs are depressurized (Ref. AMM TASK 29-14-00-614-001).
(6) Make sure that the WARNING NOTICE(S) are in position in the flight compartment to tell persons not to operate the flight controls.
(7) Make sure that the WARNING NOTICE(S) are in position to tell persons not to operate the hydraulic systems.
(8) Make sure that the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE is in position at zone 334 and/or zone 344.
(9) Make sure that access panels 334DB and/or 344DB are open (Ref. AMM TASK 55-13-11-000-001).
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
Subtask 27-34-51-140-054-A | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | FLIGHT CONTROLS/ELAC1/NORM/SPLY | 15CE1 | B11 |
| 49VU | FLIGHT CONTROLS/FCDC1/SPLY | 20CE1 | B10 |
| 49VU | FLIGHT CONTROLS/THS/ACTR/MOT2 | 19CE2 | B09 |
| 49VU | FLIGHT CONTROLS/SEC1/NORM/SPLY | 21CE1 | B08 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | FLIGHT CONTROLS/ELAC1/NORM/SPLY | 15CE1 | B06 |
| 49VU | FLIGHT CONTROLS/FCDC1/SPLY | 20CE1 | B05 |
| 49VU | FLIGHT CONTROLS/THS/ACTR/MOT2 | 19CE2 | B04 |
| 49VU | FLIGHT CONTROLS/SEC1/NORM/SPLY | 21CE1 | B03 |
| ** ON A/C ALL | |||
| 105VU | FLIGHT CONTROLS/ELAC2/STBY SPLY | 16CE2 | A02 |
| 105VU | FLT CTL/ELAC1/STBY SPLY | 16CE1 | A01 |
| 105VU | FLT CTL/SEC1/STBY SPLY | 22CE | B01 |
| 121VU | FLIGHT CONTROLS/FCDC2/SPLY | 20CE2 | Q20 |
| 121VU | FLIGHT CONTROLS/SEC2/SPLY | 21CE2 | Q18 |
| 121VU | FLIGHT CONTROLS/THS ACTR/MOT3 | 19CE3 | Q17 |
| 121VU | FLIGHT CONTROLS/THS ACTR/MOT1 | 19CE1 | Q16 |
| 121VU | FLIGHT CONTROLS/ELAC2/NORM/SPLY | 15CE2 | R20 |
C. Cleaning
(1) Clean the component interfaces and the adjacent area.
(2) Make sure that the parts retained from the removed component are clean and in the correct condition.
4. Procedure(1) Clean the component interfaces and the adjacent area.
(2) Make sure that the parts retained from the removed component are clean and in the correct condition.
Subtask 27-34-51-420-057-A
A. Install the servo control actuator MSVT
(1) Apply Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) to the bolts (4).
(2) Install the O rings (6) and (7) in the MSVT (3).
(3) Put the MSVT (3) in position on the servo control actuator and support it.
(4) Install the washers (5) and the bolts (4) into the MSVT (3).
(5) TORQUE the bolts (4) to between 0.41 and 0.33 m.daN (36.28 and 29.20 lbf.in )
(6) Remove the blanking caps.
(7) Connect the electrical connectors.
Subtask 27-34-51-081-053-A (1) Apply Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) to the bolts (4).
(2) Install the O rings (6) and (7) in the MSVT (3).
(3) Put the MSVT (3) in position on the servo control actuator and support it.
(4) Install the washers (5) and the bolts (4) into the MSVT (3).
(5) TORQUE the bolts (4) to between 0.41 and 0.33 m.daN (36.28 and 29.20 lbf.in )
(6) Remove the blanking caps.
(7) Connect the electrical connectors.
B. Remove Locking Devices
(1) Remove the 98D27903500000 PIN-SIDE STICK LOCKING from the CAPT and F/O side stick controllers.
(2) Remove the 98D27309001000 NEUTRAL SETTING TOOL - ELEVATOR from the elevator:
(a) Release the wing nut (6).
(b) Remove the T-handle screw (1) and the washer (2).
(c) Remove the set of bars (3) and plates (7) and (8).
(d) Install the T-handle screw (1) and the washer (2) in the stowage on the center plate(7).
(e) Tighten the wing nut (6).
Subtask 27-34-51-865-059-A (1) Remove the 98D27903500000 PIN-SIDE STICK LOCKING from the CAPT and F/O side stick controllers.
(2) Remove the 98D27309001000 NEUTRAL SETTING TOOL - ELEVATOR from the elevator:
(a) Release the wing nut (6).
(b) Remove the T-handle screw (1) and the washer (2).
(c) Remove the set of bars (3) and plates (7) and (8).
(d) Install the T-handle screw (1) and the washer (2) in the stowage on the center plate(7).
(e) Tighten the wing nut (6).
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
Subtask 27-34-51-710-053-A | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | FLIGHT CONTROLS/ELAC1/NORM/SPLY | 15CE1 | B11 |
| 49VU | FLIGHT CONTROLS/FCDC1/SPLY | 20CE1 | B10 |
| 49VU | FLIGHT CONTROLS/THS/ACTR/MOT2 | 19CE2 | B09 |
| 49VU | FLIGHT CONTROLS/SEC1/NORM/SPLY | 21CE1 | B08 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | FLIGHT CONTROLS/ELAC1/NORM/SPLY | 15CE1 | B06 |
| 49VU | FLIGHT CONTROLS/FCDC1/SPLY | 20CE1 | B05 |
| 49VU | FLIGHT CONTROLS/THS/ACTR/MOT2 | 19CE2 | B04 |
| 49VU | FLIGHT CONTROLS/SEC1/NORM/SPLY | 21CE1 | B03 |
| ** ON A/C ALL | |||
| 105VU | FLIGHT CONTROLS/ELAC2/STBY SPLY | 16CE2 | A02 |
| 105VU | FLT CTL/ELAC1/STBY SPLY | 16CE1 | A01 |
| 105VU | FLT CTL/SEC1/STBY SPLY | 22CE | B01 |
| 121VU | FLIGHT CONTROLS/FCDC2/SPLY | 20CE2 | Q20 |
| 121VU | FLIGHT CONTROLS/SEC2/SPLY | 21CE2 | Q18 |
| 121VU | FLIGHT CONTROLS/THS ACTR/MOT3 | 19CE3 | Q17 |
| 121VU | FLIGHT CONTROLS/THS ACTR/MOT1 | 19CE1 | Q16 |
| 121VU | FLIGHT CONTROLS/ELAC2/NORM/SPLY | 15CE2 | R20 |
D. Operational Test
(1) Do an operational test of the servo controls. (Ref. AMM TASK 27-34-00-710-001)
5. Close-up(1) Do an operational test of the servo controls. (Ref. AMM TASK 27-34-00-710-001)
Subtask 27-34-51-410-055-A
A. Visual Inspection
(1) Make sure that the work area is clean and clear of tools and other items.
Subtask 27-34-51-410-056-A (1) Make sure that the work area is clean and clear of tools and other items.
B. Close Access
(1) Close trailing-edge access panels 334DB and/or 344DB (Ref. AMM TASK 55-13-11-400-001)
Subtask 27-34-51-942-055-A (1) Close trailing-edge access panels 334DB and/or 344DB (Ref. AMM TASK 55-13-11-400-001)
C. Removal of the Ground Equipment
(1) Remove the WARNING NOTICE(S).
(2) Remove the access platform(s).
(1) Remove the WARNING NOTICE(S).
(2) Remove the access platform(s).